Ohlins SD 168 User manual

Mounting Instructions
Öhlins steering damper kit
SD 168 for Ducati 999
© Öhlins Racing AB. All rights reserved. Any reprinting or unauthorized use without the
written permission of Öhlins Racing AB is prohibited. Printed in Sweden.
Öhlins steering damper R&T
Your Öhlins steering damper R&T features the
following adjuster:
The adjustment knob has 16 different positions
and counts in number of clicks from maximum
hard position.
NOTE!
When delivered the Öhlins steering damper is
dialed to recommended setting for the specific
brand and make of the motorcycle. If you have
changed the settings follow the instruction below:
The adjusters have a normal right hand thread.
Turn clockwise to fully closed (pos. zero [0]). Turn
counter clockwise to open and count the clicks
until you reach the recommended number of
clicks. See Setup data at last page.
CAUTION!
Do not use too much force, delicate sealing
surfaces can be damaged. Use fingers only.
Adjuster
Öhlins Racing AB, Box 722, S-194 27 Upplands Väsby, Sweden.
Phone [phone]. Fax [phone].
www.ohlins.com
Part No. SD168. Issued 03 06 03
Set-up data
Recommended set-up 10 - 12 clicks from closed
Notes
NOTE!
Make sure that all bolts are tightened to the correct
torque and that nothing fouls or restricts movement
of the steering damper when the suspension is
being fully compressed or extended.
7
Tighten the bolts to correct torque. – M5 screws
5 Nm, M6 screw 10 Nm.
8
Continue your work according to the Owners
Manual, section Adjustments.

Before installation
Öhlins Racing AB can not be held responsible for
any damage whatsoever to steering damper or
vehicle, or injury to persons, if the instructions for
fitting and maintenance are not followed exactly.
Similarly, the warranty will become null and void
if the instructions are not adhered to.
WARNING!
1. Installing a steering damper, that is not
approved by the vehicle manufacturer, may
affect the stability of your vehicle. Öhlins
Racing AB cannot be held responsible for
any personal injury or damage whatsoever
that may occur after fitting the steering
damper. Contact an Öhlins dealer or other
qualified person for advice.
2. Please study and make certain that you
fully understand all the mounting instructions
and the owners manuals before handling this
steering damper kit. If you have any ques-
tions regarding proper installation proce-
dures, contact an Öhlins dealer or other quali-
fied person.
3. The vehicle service manual must be referred
to when installing the Öhlins steering damper.
Safety signals
Important information concerning safety is
distinguished in this manual by the
following notations:
The Safety alert symbol means:
Caution! Your safety is involved.
WARNING!
Failure to follow warning instructions
could result in severe or fatal injury
to anyone working with, inspecting or
using the suspension, or to bystanders.
CAUTION!
Caution indicates that special pre-
cautions must be taken to avoid dam-
age to the suspension.
NOTE!
This indicates information that is of
importance with regard to procedures.
Öhlins products are subject to continual improve-
ment and development. Consequently, although
these instructions include the most up-to-date
information available at the time of printing, there
may be minor differences between your suspen-
sion and this manual. Please consult your Öhlins
dealer if you have any questions with regard to
the contents of the manual.
NOTE!
During storage and transportation, especially
at high ambient temperature, the oil and
grease used for assembling may run out
inside the packing and damage the expanded
polystyrene packing material. This is not
unusual and is in no way detrimental to the
steering damper.
Kit contents
Before installing the steering damper, please
check the contents of the kit. If anything is
missing, contact your Öhlins dealer.
Description Pcs. Part No.
Steering damper stroke 68 1 02260-10
Bracket assy 102230-07
Spacer 1 02259-02
Sticker Öhlins 2 00192-01
WARNING!
1. It’s advisable to have an Öhlins dealer or other
qualified person to fit your steering damper.
2. Instructions in the vehicle service manual are
to be followed when changing the steering
damper.
3. When working on a lifted vehicle it must be
securely supported to prevent it from falling.
5
Mounting instructions
1
Put the motorcycle on a stand. Make sure it's
steadily fixed so it will not fall over.
2
Remove the original steering damper.
3
Fit the bracket assy to the steering damper
4
Fit the Öhlins steering damper bracket assy to
the triple clamp. Fit the spacer between the tri-
ple clamp and the bracket. Use original screw.
Do not tighten yet.
5
Fit the end eye of the steering damper to the
frame bracket. Use original screw and washer.
4
6
6
Adjust the steering damper by letting it slide in
its bracket assembly so the steering damper uses
similar stroke length both ways.
NOTE!
Make sure that there are no problems with clear-
ance when turning the steering to the left and
right end positions, and that the damper is not
used as a stop.
Sticker Öhlins 200194-10
Owners manual 1