Ohlins DU 907 User manual

Shock absorber for Ducati Sport Classic 1000
DU 907
Mounting Instructions
Note!1
Please note that there can be small differences
between your product and the images in
these instructions.
Note!1
Please note that during storage and transport,
especially at high ambient temperature, some
of the oil and grease used for assembly may
leak and stain the packaging. This will not cause
damage to the product, wipe off the excessive
oil or grease with a cloth.
Kit Contents
Description Part No Pcs
Shock absorber DU 907 2
O-ring 14x4 00338-06 4
Spacer 12x22 02118-06 2
Spacer 12x24 02118-07 2
Sticker set"ÖHLINS" 10207-01 1
C-spanner S36 60710-01 2
Owners manual 07241-02 1
Note!1
Before installing this product, check the contents
of the kit. If anything is missing, please check an
Öhlins dealer.
Warning!⚠
Before installing this product, read the Öhlins
Owner’s Manual. The shock absorber is an
important part of your vehicle and will affect
the stability.

2
1
Put the motorcycle on a work stand so that the
rear wheel barely touches the ground.
2
Loosen and remove the original shock
absorber.
3
Install the Öhlins shock absorber in the same
position as the original shock absorbers.
Note!1
Lower the vehicle so that the suspension
is slightly compressed before you tighten
the screws.
Caution!✋
Make sure that you tighten all screws to the
correct torque and that nothing fouls or restricts
movement of the shock absorber/front fork/
steering damper when the suspension is fully
compressed or extended.
MOUNTING INSTRUCTIONS
Warning!⚠
We strongly recommend to let an Öhlins dealer
install this product.
Warning!⚠
If you work with a lifted vehicle, make sure that it
is safely supported to prevent it from tipping over.
Note!1
When you work with this product, see the
vehicle service manual for vehicle specic
procedures and important data.
Note!1
Before you install this product clean the vehicle.

3
MOUNTING INSTRUCTIONS
1
wheel side
01218-03
Spacer 12x22
00228-06 (2x)
O-ring 14x4
02118-06
Spacer 12x22
01218-01
Spacer 12x24
02118-07
Spacer 12x24
RH side
Note!1
Mirrored position of spacers for the LH side

Öhlins Asia Co. Ltd
700/937 Moo5, Tambol Nongkhaga,
Amphur Phantong, Chonburi Province
20160 Thailand
© Öhlins Asia Co. Ltd. All rights
reserved. Any reprinting or
unauthorized use without the written
permission of Öhlins Racing AB
is prohibited.
Öhlins products are subject to
continuous improvement and
development, therefore, although
these instructions include the most
up-to-date information available at
the time of printing, minor updates
may occur.
To nd the latest information
contact an Öhlins distributor.
Please contact Öhlins if you have
any questions regarding the
contents in this document.
SETUP DATA
Spring
preload
adjuster
ADJUSTMENTS
Part no. MI_DU 907_EN 0
Issued 2019-09-27
Rebound
Adjuster
Length
Adjuster
Compression
Adjuster
Warning!⚠
Before riding, always make sure that the basic
settings made by Öhlins are according to
recommended
Set-up Data. Read about adjustments and setting
up in the Öhlins Owner’s Manual before you
make any adjustments. Contact an Öhlins dealer
if you have any questions about setting up.
Max. Position
Min. Position
Warning!⚠
The adjustable end eye/bracket must not be
threaded out more than that the groove is fully
visible beneath the lock nut. This is maximum
length. After adjusting, make sure that the lock
nut is tightened (30Nm).
Recommended set-up
Spring Preload........................ 17 mm.
Compression adjuster............. 2 Clicks
Rebound adjuster .................. 18 Clicks
Shock absorber data
Length ............................. 378 +8/-2 mm.
Stroke .............................. 94 mm.
Spring Installed spring
Part No ................... 60480-12
Free spring length... 230 mm
Spring rate.............. Prog 16-26 N/mm
Preload adj.range.... 0-27 mm