Hodedah HI302DR User manual

1 | P a g e
www.Hodedah.com
Assembly Instructions
This instruction booklet contains important safety information, please read and keep for future reference.
ITEM # HI302DR
3 DRAWER DRESSERW / ONE OPEN SHELF 2 COMPARTMENTS
FRONT VIEW BACK VIEW
Product Dimensions: Height 36.41" x Width 35.43" x Depth 19.68"
Weight Capacity per drawer: 20 lbs.
2 people
90mins
1 YR LTD
1 Box

2 | P a g e
www.Hodedah.com
Questions, need parts, we are here to help!
FOR PROMPT, RELIABLE SERVICE PLEASE HAVE YOUR INSTRUCTION MANUAL READY
DO NOT RETURN PRODUCT TO THE STORE
If parts are missing or damaged please contact our customer service team and we will
gladly ship your replacement parts FREE of charge within ONE YEAR of purchase!
______________________________________________
WARRANTY
Hodedah warrants this product to be free from defects in materials and workmanship and agrees to
remedy any such defect. This warranty covers one year from the date of original purchase. This is solely
limited to replacement of defective parts and no assembly for labor is included. This warranty does not
apply to any product that has been improperly assembled, subjected to misuse, abuse or which has been
altered or repaired in any way. To obtain warranty service, original purchaser must present the following;
original bill of sale, date of purchase, where the product was purchased and images if applicable.
Components replaced warranted through the remainder of the original warranty only. The defective part
will be replaced without charge, subject to the terms and conditions described above.
WARNING
This product contains small parts, keep away from children.
This product contains plastic bags, keep away from children.
Serious or fatal crushing injuries can occur from furniture tip-over. To help
prevent this, place heaviest items on the lower shelves and drawers. Do not set
heavy objects on top shelves and drawers.
Never allow children to climb or hang on drawers, shelves and doors.
Never open more than one drawer at a time.
The use of tip-over restraints may reduce but not eliminate the risk of tip-over.
Phone
Mon –Fri | 9:30 am to 5pm EST
1 - 855 –HODEDAH
1 –855 –463 -3324
Email
Send us an email
[e-mail]
Website
Visit our website to open a case
www.Hodedah.com

3 | P a g e
www.Hodedah.com
Let’s get started…
Helpful hints, read before beginning assembly
Make sure you receive all boxes. If your item is packed in one box, box count will read 1
of 1, likewise if your item is packed in two boxes, box count will read 1 of 2 and second
box will read 2 of 2.
Read each step carefully. It is very important that each step is performed in the correct
order. If these steps are not followed in sequence, assembly difficulties will occur.
Work in a spacious level area, preferably carpet, near the place the unit will be used.
DO NO USE power tools to assemble your furniture, it will strip and damage parts.
Your package should include the following hardware and parts. Parts are labeled or
stamped on the raw edge. Please inspect contents to ensure you have received all
components. If you are missing any hardware or parts please contact customer
service right away before assembly.
Assembly Tools Required(not supplied)
Hammer Phillips Screwdriver Tape Measure No Power Tools Needed
____________________________________________________________________________________
Product Care and Maintenance
Wipe clean with dry soft cloth, never use chemicals or cleaning products that will
damage the finish.
Avoid placing your furniture in direct sunlight, as sunlight causes fading.
Never push, drag or pull your furniture, to move to a new location carefully with two or
more people carry the unit to its new location.
Avoid extreme changes in temperature by arranging furniture away from radiators, heat
and air vents and air conditioning units.

4 | P a g e
www.Hodedah.com
Hardware List
A
8x25mm Dowel
QTY
36Pcs
B
Minifix
QTY
15Sets
C
M4x45mm Screw
QTY
31Pcs
D
M3.5x16mm Screw
36Pcs
E
Sticker
14Pcs
F
Drawer Slide
(300mm)
3Sets
G
5/8 Nail With Pin
4Pcs
H
Handle Moon
(96mm)
3Pcs
I
M3x21mm Screw
6Pcs
J
6/8 Power Pin
30Pcs
Important
1. Before you throw the package, please use the Check Box to identify the parts and hardware to
ensure that you have everything you need.
2. Check and measure the bolts before applying them to parts.
3. Do not completely tighten all hardware until the entire assembly is complete, unless indicated
otherwise.

5 | P a g e
www.Hodedah.com
Parts List
1 Top Panel
900x500x15mm
QTY
1Pc
2 Left Side Panel
905x498x15mm
QTY
1Pc
3 Right Side Panel
905x498x15mm
QTY
1Pc
4 Divider Panel
420x143x15mm
1Pc
5 Partition Panel
867x420x15mm
1Pc
6 Front
Strengthening Panel
867x70x15mm
2Pcs
7 Strengthening
LVL Panel
867x30x15mm
1Pc
8Kick Panel
867x80x15mm
3Pcs
9 Drawer Front
Panel
857x222x15mm
3Pcs
10 Drawer –Left
Side Panel
350x145x15mm
3Pcs
11 Drawer –
Right Side Panel
350x145x15mm
3Pcs
12 Drawer End
Panel
811x145x15mm
3Pcs
13 Drawer Base
Supporting Panel
335x50x15mm
3Pcs
14 Drawer Base
Panel
820x344x2.5mm
3Pcs
15 Back Panel -
Left
900x298x2.5mm
1Pc
16 Back Panel -
Center
900x298x2.5mm
1Pc
17 Back Panel -
Right
900x298x2.5mm
1Pc

6 | P a g e
www.Hodedah.com
The Breakdown…
1
3
2
4
5
6
6
7
8
8
9
11
10
12
13
14
15
16
17
8
9
11
10
12
13
14
9
11
10
12
13
14

7 | P a g e
www.Hodedah.com
On hardware list, you will find three bundles of drawer slide (F), left and right as shown
in picture below.
Left Drawer Slide(F)
Flat Shaped - Left
"L" Shaped - Left
Right Drawer Slide(F)
Flat Shaped - Right
"L" Shaped - Right

8 | P a g e
www.Hodedah.com
Step 1
Insert PVC dowels (A) to Panel 2, 3, 4, 5, 6, 7, 8, 10 and 11's non-thru holes as shown,
using hammer to gently tap them in.
Non-thru holes (are small indents in the wood that show you where the screws should
be.)
11
10
5
4
8
8
8
6
6
7
2
3
11
10
11
10
A
8x25mm Dowel
36Pcs

9 | P a g e
www.Hodedah.com
Step 2
Place the flat shaped - right of the
drawer slide (F) at the predrilled
holes on the panel 3 as shown .
Then tighten the drawer slide (F)
with 3 screws (D).
F
D
3
Place the flat shaped - left of the
drawer slide (F) at the predrilled
holes on the panel 2 as shown.
Then tighten the drawer slide (F)
with 3 screws (D).
2
D
M3.5x16mm Screw
18Pcs
F
Drawer Slide 300mm - Right
3Pcs
F
Drawer Slide 300mm - Left
3Pcs

10 | P a g e
www.Hodedah.com
Step 3
*Insert nails (G) protection onto the bottom edge of panel 2 and 3, slightly tapping them
in with hammer.
2
3
G
G
5/8 Nail With Pin
4Pcs

11 | P a g e
www.Hodedah.com
Step 4
*Place minifix (B) long piece onto the predrilled holes of panel 1 and 9 as shown. (You
will use 15 pieces)
B
99
9
1
B
Minifix
15Pcs

12 | P a g e
www.Hodedah.com
Step 5
*Attach panel 5 onto panel 4, align the position properly and fasten screws (C) onto the
predrilled holes to fix the panel.
5
4
C
C
M4x45mm Screw
2Pcs

13 | P a g e
www.Hodedah.com
Step 6
*Attach panel 5, 6, 7 and 8 onto panel 2, then align the position properly and slightly
hammer them in from outside of panel 2.
* Fasten screws (C) from the outside of panel 2 by using the predrilled holes to attach
panel 5, 6 and 8.
*Cover all the screws (C)' head with stickers (E) provided by stick up onto hole of screw
(C)' heads one by one.
566
8
8
8
CE
2
7
C
M4x45mm Screw
7Pcs
E
Sticker
7Pcs

14 | P a g e
www.Hodedah.com
Step 7
* Attach panel 3 onto panel 5, 6, 7 and 8 then align the position properly and slightly tap
them in with hammer.
*Fasten screws (C) onto the predrilled holes of panel 3 to fix panel 5, 6 and 8
predrilled holes.
*Cover all the screws (C)' head with stickers (E) provided by stick up onto hole of screw
(C)' heads one by one.
C
E
5
6
6
8
8
8
3
2
7
C
M4x45mm Screw
7Pcs
E
Sticker
7Pcs

15 | P a g e
www.Hodedah.com
Step 8
*Attach panel 1 onto panel 2 and 3 and align the panel 1 properly and firmly onto the
PCV dowels.
* Gently tap the panel 1 to connect panel 2, panel 3 and panel 4 firmly.
*Insert minifix (B) nuts into both sides predrilled holes of panel 2, 3 and 4, then tighten
them clockwise in order to lock minifix up by going underneath panel 1.
B
1
4
3
2
5
8
8
8
6
6
B
Minifix
6Pcs

16 | P a g e
www.Hodedah.com
Step 9
*Fix approximately 30 pieces of nails (J) into panel 15, 16 and 17 using a hammer.
15
16
17
1
3
J
6/8 Power Pin
30Pcs

17 | P a g e
www.Hodedah.com
Step 10
Assembly Of Drawer : 3 Drawers
*Insert the minifix (B) nuts
with the cross arrow mark
facing upwards and aim to
panel 10,11 and 13 's top
thru holes.(As shown)
*Insert panel 14 into the
groove of panel 10 and 11
properly. (As shown)
*Insert panel 10,11,13 onto
panel 9 by slightly hammering
the dowels.
X3
13
14
11
10
9
B
Minifix
9Pcs

18 | P a g e
www.Hodedah.com
Step 11
*Place panel 12 on each side of panel 10 and 11 as shown.
*Then, tighten screws (C) to panel 10's upper thru holes to fix them onto panel 12.
*Next tighten screws (C) to panel 11's upper thru holes to fix up to the panel 12.
*Tighten screws (C) to panel 12's upper thru holes to fix up to the panel 13.
12
13
11
X3
C
M4x45mm Screw
15Pcs

19 | P a g e
www.Hodedah.com
Step 12
*Flip the drawer over.
*Tighten 2 screws (I) from inner side of panel 9 into the handle (H) holes.
9
12
11
10
X3
H
Handle Moon (96mm)
3Pcs
I
M3x21mm Screw
6Pcs

20 | P a g e
www.Hodedah.com
Step 13
Place the "L" shaped - left drawer slide (F) with the small white roller facing outwards
and should be in parallel with drawer front panel 9. Then tighten 3 screws (D) on each
drawer slides (F).
"L" shaped - left
of the drawer
slide stick to the
end of drawer
front panel 9.
10
D
F9X3
D
F
FF
D
13
12
10
D
M3.5x16mm Screw
9Pcs
F
Drawer Slide 300mm - Left
3Pcs