Hodedah HI3DR-G User manual

Assembly Instructions
This instruction booklet contains important safety information, please read and keep for future reference.
HODEDAH ®
ITEM # HI3DR-G (MOP-SP)
3 DRAWER CHEST
2 people
60 mins
1 YR LTD
1 Box
www.Hodedah.com 1| Page
FRONT VIEW BACK VIEW
Weight Capacity Per Drawer 25lbs
Product Dimensions: Height 30.59" x Width 31.49" x Depth 15.86"

HODEDAH ®
www.Hodedah.com 2| Page
DO NOT RETURN PRODUCT TO THE STORE
Phone WebsiteEmail
Questions, need parts, we are here to help!
WARRANTY
WARNING
If parts are missing or damaged please contact our customer service team and we will
gladly ship your replacement parts FREE of charge within ONE YEAR of purchase!
Hodedah warrants this product to be free from defects in materials and workmanship and agrees to
remedy any such defect. This warranty covers one year from the date of original purchase. This is solely
limited to replacement of defective parts and no assembly for labor is included. This warranty does not
apply to any product that has been improperly assembled, subjected to misuse, abuse or which has been
altered or repaired in any way. To obtain warranty service, original purchaser must present the following;
original bill of sale, date of purchase, where the product was purchased and images if applicable.
Components replaced warranted through the remainder of the original warranty only. The defective part
will be replaced without charge, subject to the terms and conditions described above.
Mon - Fri | 9:30 am to 5pm EST Send us an email
FOR PROMPT, RELIABLE SERVICE PLEASE HAVE YOUR INSTRUCTION MANUAL READY
Visit our website to open a case
1 - 855 - HODEDAH
1 - 855 - 463 -3324
[email protected] www.Hodedah.com
·This product contains small parts, keep away from children.
·This product contains plastic bags, keep away from children.
·Serious or fatal crushing injuries can occur from furniture tip-over. To help
prevent this, place heaviest items on the lower shelves and drawers. Do not set
heavy objects on top shelves and drawers.
·Never allow children to climb or hang on drawers, shelves and doors.
·Never open more than one drawer at a time.
·The use of tip-over restraints may reduce but not eliminate the risk of tip-over.

HODEDAH ®
www.Hodedah.com 3| Page
Product Care and Maintenance
Let's get started…
·Never open more than one drawer at a time.
·The use of tip-over restranits may reduce but not eliminate the risk of tip-over.
·Make sure you receive all boxes. If your item is packed in one box, box count will read 1
of 1, likewise if your item is packed in two boxes, box count will read 1 of 2 and second
box will read 2 of 2.
·Read each step carefully. It is very important that each step is performed in the correct
order. If these steps are not followed in sequence, assembly difficulties will occur.
·Work in a spacious level area, preferably carpet, near the place the unit will be used.
·DO NO USE power tools to assemble your furniture, it will strip and damage parts.
·Your package should include the following hardware and parts. Parts are labeled or
stamped on the raw edge. Please inspect contents to ensure you have received all
components. If you are missing any hardware or parts please contact customer
service right away before assembly.
Helpful hints, read before beginning assembly
Assembly Tools Required (not supplied)
·Wipe clean with dry soft cloth, never use chemicals or cleaning products they will
damage the finish.
·Avoid placing your furniture in direct sunlight, as sunlight causes fading.
·Never push, drag or pull your furniture, to move to a new location carefully with
two or more people carry the unit to its new location.
·Avoid extreme changes in temperature by arranging furniture away from radiators,
heat and air vents and air conditioning units.
Hammer Phillips Screwdriver No Power Tools NeededTape Measure

HODEDAH ®
www.Hodedah.com 4| Page
Hardware List
1QTY
Screw M6 x 40mm 8 Pcs
Pvc Cap
2QTY
Screw M4 x 32mm
15 Pcs
3QTY
Screw M3.5 x 14mm
24 Pcs
QTY
16 Sets
6QTY 7QTY
Pvc Dowel
24 Pcs
8QTY 9QTY
Nail
45 Pcs
12 QTY
Allen Key
1 Pc
12 Pcs
Pvc Cap
Mini Fix
8 Pcs
16 Pcs
5
Screw M6.2 x 10mm
*For # 10 Drawer Slides
*For # 11 Drawer Slides
(separate from
hardware pack)
Anti-Tip Kit
1 PK

* Fix On Side Panels Ⓐ
HODEDAH ®
www.Hodedah.com 5| Page
Accessories
4QTY
Handle 3 Pcs
Screw M4 X 32mm 6 Pcs
* Fix On Drawer Side Panels Ⓘ
* Fix On Side Panels Ⓔ
* Fix On Drawer Side Panels Ⓙ
10
11
Drawer Slide - A
*Fix On Side Panels A & E
QTY
3 Sets
QTY
3 Sets
*Fix On Side Panels I& J
Drawer Slide - B
Important
1. Before you throw the package, please use the Check Box to identify the parts
and hardware to ensure that you have everything you need.
2. Check and measure the bolts before applying them to parts.
3. Do not completely tighten all hardware until the entire assembly is complete,
unless indicated otherwise.

HODEDAH ®
www.Hodedah.com 6| Page
AQTY
1 Pc
BQTY CQTY
1 Pc
DQTY
1 Pc
EQTY F
QTY
1 Pc
1 Pc
GQTY
HQTY I
QTY
3 Pcs
Parts List
JQTY KQTY
QTY
M
L
Drawer - Left Side Panels
338 x 140 x 15mm
Kick Panel (Front)
766 x 90 x 15mm
Drawer Base Panels
740 x 343 x 3mm
Drawer Front Panels
759 x 218 x 15mm
Left Side Panel
762 x 394 x 15mm
Drawer End Panels
711 x 140 x 15mm
Drawer - Right Side Panels
338 x 140 x 15mm
Top Panel
699 x 394 x 15 mm
Kick Panel (Back) & Back
Strengthening Panel
766 x 400 x 15mm
Drawer Support Panel
338 x 5 6 x 15 mm
Back Panels
795 x 397 x 3mm
QTY
1 Pc
Right Side Panel
762 x 394 x 15mm
Front Strengthening Panel
766 x 76 x 15mm
1 Pc
3 Pcs
3 Pcs 3 Pcs 3 Pcs
3 Pcs

HODEDAH ®
www.Hodedah.com 7| Page
The Breakdown
x3

HODEDAH ®
www.Hodedah.com 8| Page
Pre - Assembly
Screw M6.2 x 10mm
12 Pcs.
7
Mini Fix
4 Pcs.
5Pvc Dowel
4 Pcs.
6
2. Insert the mini fix ⑤(nuts) with the cross arrow mark facing outward and aim to panels A and E's top thru
holes. (As shown)
3. Insert the pvc dowels ⑥to panels Aand E 's non-thru holes as shown, using hammer to gently tap them in.
1. Place the drawer slide A ⑩onto the 2 holes area shown at left side of panels A and right side of
panel E. Then tighten it with 2 screws ⑦ and 1 screw ③. Do the same for the 3 other slide A ⑩.
Screw M3.5 x 14mm
6 Pcs.
3
6
6
5
5
37
7
10
37
7
10
37
7
10
PANEL E
PANEL A
5
5
10
3
7
7
10
3
7
7
10
3
7
7
6
6

HODEDAH ®
www.Hodedah.com 9| Page
Pre - Assembly
5Mini Fix
4 Pcs.
Pvc Dowel
8 Pcs.
6
Insert, push down
and tighten mini fix
screw ⑤, to the
non-thru hole of
the panel Fas
shown, 4pcs.
Insert the pvc
dowels ⑥to both
end of the panels
B,C,Dand F.
Using hammer to
gently tap them in.
5
5
5
5
PANEL F
6
6
6
6
PANEL C
6
6
PANEL D
6
6
PANEL B

Screw
M 6 x 40mm
4 Pcs.
1Allen Key
1 Pc.
9
HODEDAH ®
www.Hodedah.com 10| Page
Step 1
1. Place and fix Panels B,C,Donto Panel Aby inserting the (Left) dowels onto
the non-thru holes at Panel A.
2. Using Allen key ⑨to tighten screws ①from the 4 thru holes of panel A,
one by one.
1
1
1
1

HODEDAH ®
www.Hodedah.com 11| Page
Step 2
Screw
M 6 x 40mm
4 Pcs.
1Allen Key
1 Pc.
9
1. Place and fix Panels B,C,Donto Panel Eby pushing and slotting the (Right) dowels
onto the non-thru holes at Panel E.
2. Using Allen key ⑨to tighten screws ①from the 4 thru holes of panel E, one by one.
1
1
1
1

Mini Fix Cap
4 Pcs.
5
Dowel / Mini Fix Installation
HODEDAH ®
www.Hodedah.com 12| Page
Step 3
Then, tighten mini fix ⑤ clockwise to lock
the mini fix up for tightening panel Fup.
Cover 4 mini fix caps provided by pushing
the cover 's stem onto the hole of mini fix
nut on upper side of panel Aand F.
Place and fix panel Fonto panels Aand panel E, and align properly by
inserting the 4 (down) mini fix screws ⑤onto the L-thru holes at top edge of
panel Aand E. At the same time, inserting panel Aand panel E's upside
dowels going onto panel F's non-thru holes.

HODEDAH ®
www.Hodedah.com 13| Page
5Mini Fix
12 Pcs.
5Mini Fix
12 Pcs. 6Pvc Dowel 12 Pcs.
Step 4
2. Insert the PVC dowels ⑥to panel I,J and M ’s non-thru holes as shown, using
hammer to tap them in.
1. Insert the mini fix ⑤(nuts) with the cross arrow mark facing upward and aim to
panel I & J 's top thru holes. (As shown)
3. Insert, push down and tighten mini fix screw ⑤, to the hole as shown (Panel G)
55
5
5
PANEL G
6
55
PANEL I
6
55
PANEL J
66
PANEL M
x3
x3
x3
x3

HODEDAH ®
www.Hodedah.com 14| Page
Assembly Of Drawers
3
Screw M3.5 x 14mm
18 Pcs.
2
Screw M4 x 32mm
15 Pcs. 4
Handle
3 Pcs. 8
(1)
Nail
24 Pcs.
(2)
x3
1. Place panel Iand J on each side of panel G
with Panel I and J 's PVC dowel insert to panel
G 's non-thru hole and Panel G 's mini fix screws
insert into Panel I and J 's thru holes as shown.
Then tighten mini fix on panel I and J clockwise to
lock mini fix up.
Next, tighten screw ②to panel I and J 's upper
thru holes to fix up to the panel K.
2. Flip drawer with bottom side
up, place panel Lonto the
drawer and align properly. Then
nail the
nails provided with hammer on
the border of panel Las
shown.The gap between 2 nails
should be about 100mm.
After that, place a drawer slide B
⑬with the small white roller
facing outward and with other
end tip touching panel Gonto
each bottom side (angle) edge of
panel Iand J. Then
tighten 3 screws ③on each
drawer slide B ⑬(as shown).
Place and fix Panel Monto Panel
Gby inserting the dowels onto
the non-thru holes at Panel G.
Then tighten screw ②to panels
M's thru holes to fix them onto
panels Kand L.
3. Flip the drawer over.
4. Tighten 2 screw ④from inner side of panel Ginto the handle ⑧holes.
(3)
4
Screw M4 x 32mm
6 Pcs.

HODEDAH ®
www.Hodedah.com 15| Page
Step 5
PVC Cap
10 Pcs.
1
1. Lift up the main unit carefully and let it stand up properly.
2. Cover all the screws ①'s head with the PVC cap provided by pushing
the cover's stem onto the hole of screw head one by one for all screws on
panels Aand E.
3. Take all drawers , and slide them (the white rollers at drawer slide at
both side of drawers are to go into the track of the slides at each side
panel.) all the way gently, one drawer by one drawer starting from
bottom one
1
1
1
1

HODEDAH ®
www.Hodedah.com 16| Page
Step 6
1. Place the back Panels Honto the back of the main unit as
shown, then align them properly for nailing.
2. Then use hammer to nail the nails one by one and at center of 4
side edges. Gap between 2 nails should be about 100mm for all.
8Nail
20 Pcs.
8
1
1
1
1

HODEDAH ®
www.Hodedah.com
b
TP 6#x5/8'' Screw
2Pcs.
Mounting bracket
4Pcs. d
Restraint strap
2Pcs.
·Attach the mounting bracket a to the furniture in the
solid part below the top panel a few inches away from the
side of the unit.
·Screw b through the smallest hole of a .
FITTING OF ANTI-TIP SAFETY STRAP
STEP 1:
STEP 2:
·Locate a stud in the wall
behind the unit,does not
have to be centered.
·Place the other mounting
bracket a on the wall
stud 2 inches below the
mounting bracket
secured to the back of
your unit.
·Attach to the wall stud
using c through the
smaller hole of a .
·Repeat the same step a few inches away from
the other side of the unit.
·Place the furniture into position so both mounting
brackets are vertically in line.
·Lace the end of the restraint strap through the
larger holes in each mounting bracket.
·Secure the straps and lock into place.
STEP 3:
TP 8#x2'' Screw
2Pcs.
BACK SIDE OF
TOP PANEL
WALL
ac
FURNITURE
17| Page

HODEDAH ®
www.Hodedah.com 18| Page
Completion
Enjoy & Thank you for purchasing from Hodedah!