Hoist Fitness CL-2103 User manual

Note: Both Serial Number and Model Number are Required when Ordering Parts
August 2000
OWNERS MANUAL
RECORD SERIAL NUMBER HERE
Customer Service
Fa x
[phone]
[phone]
[phone]
CL-2103
FITNESS SYSTEMS
R
HOIST

Page - 1 2103 Assembly
CONTENTS
ASSEMBLY
INSTRUCTIONS
FITNESS SYSTEMS
R
HOIST
INSTRUCTIONS (Step 1) .............................................................
FRAME ASSEMBLY (Step 2) ........................................................
PARTS LISTING ............................................................................
HARDWARE LISTING ..................................................................
BOLT SIZING CHART ..................................................................
WASHER SIZING CHART ............................................................
WEIGHT RATIOS .........................................................................
WEIGHT TRAINING TIPS ...........................................................
WEIGHT TRAINING EXERCISE LOG ......................................
DECAL PLACEMENTS ....................................................................
GENERAL MAINTENANCE..........................................................
LIMITED WARRANTY ..................................................................
2
4
23
24
26
27
28
30
32
34
39
42

ASSEMBLY
INSTRUCTIONS
INSTRUCTIONS
Page - 22103 Assembly
Step 1
TOOLS REQUIRED
Before beginning assembly please take the time to read the
instructions thoroughly. Please use the catalog in this manual to
make sure that all parts have been included in your shipment.
Use only Hoist replacement parts when servicing. Failure
to do so will void your warranty and could result in personal
injury.
Hoist equipment is designed to provide the smoothest, most
effective exercise motion possible. After assembly, you should
check all functions to ensure correct operation. If you
experience problems, first recheck the assembly instructions to
locate any possible errors made during assembly. If you are
unable to correct the problem, call your authorized Hoist dealer.
Be sure to have your serial number and this catalog when calling.
When all parts have been accounted for, continue on to Step 2.
When ordering use the part number and description from the
catalog.
FITNESS SYSTEMS
R
HOIST
Standard Allen Wrench Set
(2.5mm, 3/32” - 5/16”)
Crescent Wrench
Belt Tensioning Wrench
(Hoist Tool SM374)
Rubber Mallet
Tape Measure

FITNESS SYSTEMS
R
HOIST
Page - 3 2103 Assembly
ASSEMBLY
INSTRUCTIONS

ASSEMBLY
INSTRUCTIONS
FRAME ASSEMBLY
Page - 42103 Assembly
Step 2
FITNESS SYSTEMS
R
HOIST
FACTORY INSTALLATION INSTRUCTION ONLY
1. ALL THREADED HOLES SHOULD BE TAPPED,
EXCEPT INSERTS.
2. ALL CALLED OUT INSERTS MUST BE INSTALLED BEFORE
ANY ASSEMBLY.
3. PUT A DROP OF ON BOLTS IF
NECESSARY.
4. IF NECESSARY APPLY TO ALL
BEARINGS.
BLUE LOCTITE 242
GREEN LOCTITE 680

ASSEMBLY
INSTRUCTIONS
FRAME ASSEMBLY
In this step attach the Weight Cage to the Seated Frame.
bolts only, they will be tightened later. Lift Machine to position Rubber
Feet.
Hand Tighten
Step 2a
1 - Weight Cage
2 - Seated Frame
Part Descriptions
A - 1/2-13 x 1 1/2” Button Head Screw
B - 1/2” Flat Washer
T - 1/2” Lock Washer
AM - 3/8”-16 Insert
AL - 1/2”-13 Insert
AQ - 4.74” x 5.24” x .625 Rubber Foot Pad
Hardware Descriptions
FITNESS SYSTEMS
R
HOIST
Page - 5 2103 Assembly

ASSEMBLY
INSTRUCTIONS
Page - 62103 Assembly
FITNESS SYSTEMS
R
HOIST
A
A
A
A
T
B
B
B
AQ
T
TT
B
AQ
AQ
2
1
AM
AL
For clarity
see A-1
For clarity
see A-1
AM AL
A-1
All inserts are factory installed, non-removable
(Inserts AM have 4 on both sides of mount)
A-1
All inserts are factory installed, non-removable
(Inserts AM have 4 on both sides of mount)

ASSEMBLY
INSTRUCTIONS
FRAME ASSEMBLY
In this step, start by sliding one 1 ¼” dia. x 3/8” Aluminum Ring on each side of
the Handle Assembly. Then, slide on one 1.25” O.D. x 1.030” I.D. x 8.25” Comfort grip
on each side. Placea1¼Dia. x 3/4” Aluminum Cap on the end of the Handle Assembly.
Once all three pieces(per side) are in place, secure the End Caps, slide the Comfort
Grip flush with the End Caps, and slide the Aluminum Rings flush with the Comfort
Grip and secure. Next, secure a 1 3/8” Dia. Flat Head Cap to the elbow of the Arm
Assembly. Then attach the two Flange Bearings to the Weight Cage. Make sure to put
zerk fitting facing down on Flange Bearings. Then, press both 1” Oilite Bushings on
the ends of the Handle Assembly. Now attach the Pivot Assembly to the Arm Assembly.
Slide one Metal Shim Washer on to the shaft of the Pivot Assembly. Attach the
play and the Hand Bar still
moves freely. Slide the entire Arm Assembly through the Flange Bearings and the
Weight Cage, insert the end into the Cam Assembly and secure with the 3/8” x 2” Open
Roll Pin. bolts only, they will be tightened later.Hand Tighten
Handle
Assembly to the Pivot Assembly and slide on another Shim Washer, place a 1 3/8”
diameter Flat Head Cap and secure, then check for side to side play. If there is play,
remove the Handle Assembly and add another Shim Washer to each side of the Handle
Assembly. Repeat if necessary until there is no noticeable
Step 2b
FITNESS SYSTEMS
R
HOIST
3 - Arm Assembly
4 - Pivot Assembly
5 - Handle Assembly
6 - Cam Assembly
28 - Black Plastic Ring
Part Descriptions
C - 3/8” x 1” Flat Head Cap Screw
D - 3/8” x 1 1/4” Button Head Screw
E - 3/8” Flat Washer
H - 3/8” x 3/4” Socket Head Cap Screw
P - 3/8” Lock Washer
V - 3/8” x 2” Open Roll Pin
W - 3/8” Lock Washer
X - 1” I. D. x .8mm Thick Metal Shim Washer
Y
AA - 1 3/8” Dia. Flat Head Cap, 3/8”I. D. x 5/16” Thick
AB - 1” I.D. Oilite Bushing
AC - Flange Bearing
AN - 1.25” O.D. x 1.03 I.D. x 8.25 Comfort Grip
AU - 1 1/4” dia. x 3/4” Aluminum Cap
AV-11/4”d
M - 3/8” x 3/4” Button Head Screw
- #10-32 Set Screw
ia. x 3/8” Aluminum Ring
BD - 1 5/8” Dia. Aluminum Flat Head Cap, Red
Hardware Descriptions
Page - 7 2103 Assembly

ASSEMBLY
INSTRUCTIONS
Page - 82103 Assembly
FITNESS SYSTEMS
R
HOIST
D
E
C
P
D
E
W
6
3
BD
AB
M
AB
H
5
X
X
For Assembly
instructions see page 17-18
For Assembly
instructions see page 17-18
D
4
P
M
W
W
AA
AC
28
AU
Make Sure the longest
slot side is facing down.
Make Sure the longest
slot side is facing down.
For clarity see detail A-1For clarity see detail A-1
C
AV
AN
AU
AN
Y
A-1
AV
Y
Y
Y
5
E
W
E
D
V
Quantity will depend
on gap due to tolerance
Quantity will depend
on gap due to tolerance

ASSEMBLY
INSTRUCTIONS
FRAME ASSEMBLY
Step 2c
7 - 41 13/16 x 3/4” Dia. Guide Rod
8 - 20 LBS. Intermediate Weight
9 - 15 LBS. Aluminum Top Plate
10 - 3” x 1” I.D. x 1 1/2” THK Bumper
11 - Guide Rod Bushing (PLAS 134)
12 - Center RH BRK (Add-on)
13 - 12” x 14 1/2” Upholstery Seat
14 - Seat Adjuster
22 - 5/8” Dia. x 6 13/32” Rod
27 - Add On Weight Bushing
Part Descriptions
J - 5/16” x 1 1/4” Button Head Cap Screw
K - 3/8” x 2 3/4” Button Head Cap Screw
L - 5/16” Flat Washer
P - 3/8” Lock Washer
S - 3/8” x 1” Button Head Cap Screw
U - 5/16” Lock Washer
Z - 3/8” Split Washer
AR - 5 LBS. Add on Weight
AS - Weight Selector Pin
AT - Selector Pin Lanyard
AX - Guide Bearing
AY - Guide Bearing
BC - 5/16” x 1” Button Head Screw
BF - 5/16” Lock Washer (black)
BG - 3/8” Flat Washer (white zinc)
BH - 3/8” Lock Washer (black)
BJ - 5/16” Flat Washer (white zinc)
Hardware Descriptions
In this step start by pressing two Guide Rod Bushings into the Weight Cage.
Take the two 3” x 1” I.D. Bumpers and place them over the two holes in the bottom
of the Weight Cage and slide the Guide Rods into the holes. Make sure the Guide
Rods are lube with Spindle Oil. Now slide the 20 LBS. Intermediate Weight Plates
and 15 LBS. Aluminum Top Plate onto the Guide Rods and secure. Make sure the
Weight Stack and its Guide Rods are sitting level. Next, attach the 5/8” Dia. x 6
13/32” Rod to the Center RH BRK (Add-On). Secure the Center RH BRK (Add-On)
to the 15 LBS. Aluminum Top Plate. Slide on three 5 LBS. Add-On Weights and
attach the 5/8” Dia. x 6 13/32” Rod to the Weight Assembly. Attach the 12” x 14 1/2”
Upholstery Seat to the Seat Adjuster. Attach one end of the Selector Pin Lanyard to
the 15 LBS. Aluminum Top Plate, and the other end to the Weight Selector Pin.
Then bolts including all previously hand tightened boltsWrench tighten .
FITNESS SYSTEMS
R
HOIST
Page - 9 2103 Assembly