Hoist Fitness MC-7011 User manual

Fax
[phone]
[phone]
Customer Service
[phone]
RECORD SERIAL NUMBER HERE
MACHINE CODE
OWNER'S MANUAL
Note: Both Serial Number and Model Number are Required when Ordering Parts
A02
MC-7011
MONKEY BARS

02
04
13
14
15
17
18
19
25
27
28
29
30
PAGE 01
OWNER'S MANUAL
WEIGHT TRAINING TIPS.......................................................
MC-7011 ASSEMBLY
LIMITED WARRANTY............................................................
INSTRUCTIONS .....................................................................
FRAME ASSEMBLY ..............................................................
PRE-ASSEMBLY....................................................................
DECAL PLACEMENT.............................................................
DECAL REFERENCE.............................................................
PART LIST...............................................................................
ABBREVIATIONS...................................................................
BOLT SIZING CHART............................................................
WASHER SIZING CHART......................................................
MAINTENANCE SCHEDULE.................................................
GENERAL MAINTENANCE INFORMATION........................
CONTENTS

OWNER'S MANUAL
PAGE 02MC-7011 ASSEMBLY
Ratchet Wrench
1/2", 9/16" and 3/4" Sockets
Adjustable Wrench
Rubber Mallet
Tape Measure
Level
Hex Key Wrench Set
Three People
Drift Pin
TOOLS REQUIRED
Before beginning assembly please take the time to read instructions
thoroughly. Please use the various lists in this manual to make sure that
all parts have been included in your shipment. When ordering, use part
number and description from the lists. Use only HOIST replacement parts
when servicing. Failure to do so will void your warranty and could result
in personal injury.
HOIST equipment is designed to provide the smoothest, most effective
exercise motion possible. After assembly, you should check all functions to
ensure correct operation. If you experience problems, first recheck the
assembly instructions to locate any possible errors made during assembly.
If you are unable to correct the problem, call your authorized HOIST dealer.
Be sure to have your serial number and this manual when calling. When all
parts have been accounted for, continue on.
INSTRUCTIONS

OWNER'S MANUAL
PAGE 03 MC-7011 ASSEMBLY
***THIS PAGE WAS INTENTIONALLY LEFT BLANK***

OWNER'S MANUAL
PAGE 04
MC-7011 ASSEMBLY
FRAME ASSEMBLY

**
ASSEMBLE ALL THE UNITS THAT MAKE UP EACH OF
THE MOTION CAGE'S CORNERS
***
STEP 1:
MC-7012
- HAND TIGHTEN HARDWARE.
- SOME PARTS MAY HAVE BEEN
REMOVED FOR CLARITY.
FRAME ASSEMBLY
NOTE:
OWNER'S MANUAL
PAGE 05 MC-7011 ASSEMBLY

FRAME ASSEMBLY
OWNER'S MANUAL
MC-7011 ASSEMBLY PAGE 06
STEP 2:
PLACE EACH ASSEMBLED CORNER IN DESIRED LOCATION. MOVE THE
CORNERS TO THE MEASUREMENTS BELOW BEFORE CONTINUING.
69 15/16" 1777
51 5/16" 1304
89" 2260

FRAME ASSEMBLY
NOTE:
- HAND TIGHTEN HARDWARE.
- REPEAT ASSEMBLY FOR OPPOSITE SIDE.
- SOME PARTS MAY HAVE BEEN
REMOVED FOR CLARITY.
* ITEMS INCLUDED WITH MC-7020
PAGE 07
OWNER'S MANUAL
MC-7011 ASSEMBLY
17
21
3
STEP 3:
BEGIN ASSEMBLING THE MC-7011 - MONKEY BARS
*
*
*
*
17
19
4
*

*
*
*
*
*
MC-7013
MC-7015
*
*
*
FRAME ASSEMBLY
NOTE:.
- HAND TIGHTEN HARDWARE.
- SOME PARTS MAY HAVE BEEN
REMOVED FOR CLARITY.
* ITEMS INCLUDED WITH MC-7020
OWNER'S MANUAL
MC-7011 ASSEMBLY PAGE 08

FRAME ASSEMBLY
- HAND TIGHTEN HARDWARE.
REMOVED FOR CLARITY.
- SOME PARTS MAY HAVE BEEN
NOTE:
OWNER'S MANUAL
PAGE 09 MC-7011 ASSEMBLY
16
20
2
16
22
7
3