Hoist Fitness MC-7033 User manual

Fax
[phone]
[phone]
Customer Service
[phone]
RECORD SERIAL NUMBER HERE
MACHINE CODE
Note: Both Serial Number and Model Number are Required when Ordering Parts
OWNER'S MANUAL
A00
MC-7033
HEAVY BAG WITH MOUNT

ABBREVIATIONS...................................................................
OWNER'S MANUAL
PAGE 01 MC-7033 ASSEMBLY
LIMITED WARRANTY............................................................
INSTRUCTIONS .....................................................................
FRAME ASSEMBLY ..............................................................
PART LIST...............................................................................
CONTENTS
02
04
09
10
11

OWNER'S MANUAL
PAGE 02MC-7033 ASSEMBLY
Ratchet Wrench
1/2", 9/16" and 3/4" Sockets
Adjustable Wrench
Rubber Mallet
Tape Measure
Level
Hex Key Wrench Set
Two People
TOOLS REQUIRED
Before beginning assembly please take the time to read instructions
thoroughly. Please use the various lists in this manual to make sure that
all parts have been included in your shipment. When ordering, use part
number and description from the lists. Use only HOIST replacement parts
when servicing. Failure to do so will void your warranty and could result
in personal injury.
HOIST equipment is designed to provide the smoothest, most effective
exercise motion possible. After assembly, you should check all functions to
ensure correct operation. If you experience problems, first recheck the
assembly instructions to locate any possible errors made during assembly.
If you are unable to correct the problem, call your authorized HOIST dealer.
Be sure to have your serial number and this manual when calling. When all
parts have been accounted for, continue on.
INSTRUCTIONS

OWNER'S MANUAL
PAGE 03 MC-7033 ASSEMBLY
***THIS PAGE WAS INTENTIONALLY LEFT BLANK***

OWNER'S MANUAL
PAGE 04
MC-7033 ASSEMBLY
FRAME ASSEMBLY

THE DISASSEMBLED HARDWARE
IMPORTANT
WILL BE USED AGAIN ON PAGE 7
22 16 16 26
4
13
MC-7021
OWNER'S MANUAL
PAGE 05 MC-7033 ASSEMBLY
NOTE:
- CORRESPONDS TO THE
MC-7021 MANUAL.
- SOME PARTS MAY HAVE BEEN
REMOVED FOR CLARITY.
FRAME ASSEMBLY
DISASSEMBLE HARDWARE

7
7
HEAVY BAG, AS SHOWN
3
8
2
8
9
10
PLACE U-BOLT (7) ON EACH
OF THE 3 STRAPS ON THE 7
OWNER'S MANUAL
MC-7033 ASSEMBLY PAGE 06
FRAME ASSEMBLY
NOTE:
- WRENCH TIGHTEN HARDWARE.
- SOME PARTS MAY HAVE BEEN
REMOVED FOR CLARITY.

LOOSEN AND RETIGHTEN BOLT.
22 16
16 26
13
1
IT MAY BE NECCESSARY TO
NOTE:
DO NOT OVERTIGHTEN
BOLT (26). IF HEAVY BAG
DOES NOT PIVOT SMOOTHLY,
MC-7021
REINSTALL HARDWARE
OWNER'S MANUAL
PAGE 07 MC-7033 ASSEMBLY
FRAME ASSEMBLY
NOTE:
- CORRESPONDS TO THE
MC-7021 MANUAL.
- WRENCH TIGHTEN HARDWARE.
- SOME PARTS MAY HAVE BEEN
REMOVED FOR CLARITY.

OWNER'S MANUAL
MC-7033 ASSEMBLY PAGE 08
FRAME ASSEMBLY
NOTE:
- WRENCH TIGHTEN HARDWARE.
- SOME PARTS MAY HAVE BEEN
REMOVED FOR CLARITY.
10
THE DESIRED HOLE IN THE HEAVY BAG MOUNT (1)
HEAVY BAG BY INSTALLING THE BOLT (4) INTO
4
6
56
1
2
IN THIS STEP, ADJUST THE HEIGHT OF THE
IMPORTANT

ITEM NO. PART NUMBER DESCRIPTION QTY.
1 026-01X7076 HEAVY BAG MOUNT STEM 1
2 026-01X7077 HEAVY BAG MOUNT HUB 1
3 012-0609001 3/8"-16 NUT, HEAVY, UNPLATED 6
4 011-0116112 1/2"-13UNC X 2.25" LOW HEAD SHCS (Ni) 1
5 012-0504002 1/2"-13 UNC THIN NYLOCK NUT (Ni) 1
6 013-1002006 1/2" X 27mm SAE FLAT WASHER (Ni) 2
7 026-01M3301 U-BOLT 3
8 013-1002007 3/8" X 22mm FLAT WASHER (Ni) 12
9 012-0504005 3/8"-16 UNC THIN NYLOCK NUT (Ni) 6
10 FAIRTEX HB6 BANANA BAG FAIRTEX HB6 BANANA BAG 1
OWNER'S MANUAL
PAGE 09 MC-7033 ASSEMBLY
NOTE: SOME OF THESE PARTS MAY COME PRE-INSTALLED
PART LIST