Home Styles 6660-30 User manual

Hardware List
Part List
Tool(s) required for assembly: Level
6660-30
Dining Table
IMPORTANT
Carefully remove all the parts from the carton and place them
individually on a soft cloth to prevent scratches or other damage.
Carefully and strictly follow these assembly instructions
to ensure a completed product as designed.
This product is made of aluminum. Do not use power tools
above 8 volts to assemble and only tighten bolts until snug.
Over tightening can damage the aluminum.
A.
Top
1 pc.
C.
Stretcher
4 pcs.
B.
Leg
4 pcs.
Hex Wrench
1 pc.
Small Hex Wrench
1 pc.
M8x30
Bolt
4 pcs. (+1 extra)
Flat Washer
12 pcs. (+1 extra)
Spring Washer
12 pcs. (+1 extra)
M8
Nut
12 pcs. (+1 extra)
Cap
12 pcs. (+1 extra)
Cover
1 pc.
Wrench
1 pc.
styles Customer Service: www.homestylesfurniture.com,home
[email protected], 888-680-7460

Assembly Instructions 2/3
IMPORTANT
Use a soft cloth between these parts and the floor.
Do not use power tools above 8 volts to assemble.
Do not tighten all the bolts until each part is properly assembled.
The unit must be level to work properly. Use the included adjustable levelers to level.
Keep Wrench as the bolts may need to be tightened in the future.
STEP 1
Attach Legs (B) to Stretchers (C) with Flat Washers, Spring Washers and Nuts,
tightening Nuts only halfway. (See Figures 1 and 2)
Figure 1 Figure 2
Flat Washer
Spring Washer
Nut
B
C
CC
B
B
B
C

Assembly Instructions 3/3
Figure 4
STEP 3
Turn table over to its upright position.
Cover umbrella hole with Cover.
Level table by adjusting the adjustable
levelers on bottom of legs.
(See Figure 4)
Cover
Cap
Nut
Spring Washer
Flat Washer
Bolt
A
STEP 2
Place Top (A) upside down on a soft cloth.
Insert Bolts into pre-drilled holes in Top (A),
then tighten. (See Figure 3)
Attach unit to Top (A) with Flat Washers,
Spring Washers and Nuts,
tightening Nuts only halfway.
Tighten all Nuts used in Steps 1 and 2.
Cover all Nuts with Caps.
Figure 3

NEVER
use glass cleaners on
finished furniture. Ammonia
chemically attacks the finish.
allow liquids to remain on furniture.
Absorption causes parts to warp
and split and finishes to delaminate.
NEVER
CARE INSTRUCTIONS
Do not use rubber
based placemats.
PREVENT
DISCOLORING
Do not use commercial
waxes and polishes.
PREVENT
YELLOWING
Do not place hot
objects on surface.
PREVENT
FINISH DAMAGE
Do not write
directly on surface.
PREVENT
MARKING
Do not use power tools
above 8 volts to assemble.
PREVENT
CRACKING
Do not place
in direct sunlight.
PREVENT
FADING
with a soft cloth moistened
in lukewarm soap and water.
Buff with a dry clean cloth.
CLEAN
homestyles will provide replacements free of charge for missing or damaged parts within 2 years of purchase.
Digital images of the defective parts may be required. If the product was not purchased from an authorized retailer,
homestyles is under no obligation to provide replacement parts. Parts are not available for fully assembled items nor
are parts available for sale. Replacements for missing or damaged parts may be requested via contact info below.
styles Customer Service: www.homestylesfurniture.com,home
[email protected], 888-680-7460