Home Styles 20 05507 0009 User manual

Hardware List
Part List
Carefully remove all the parts from the carton and
place them individually on a soft cloth to prevent
scratches or other damage.
Carefully and strictly follow these assembly instructions
to ensure a completed product as designed.
Do not use power tools above 8 volts to assemble.
Tool(s) required for assembly: Phillips screwdriver, Level, Drill (8 volts or less), 3/8” Drill Bit
Home Styles Customer Service: www.homestyles-furniture.com,
[email protected], 888-680-7460, 877-831-0319
20 05507 0009
Entertainment Stand
IMPORTANT
D.
Side Panel
1 pc.
F.
Middle Panel
1 pc.
A.
Top
1 pc.
B.
Bottom
1 pc.
C.
Side Panel
1 pc.
E.
Middle Panel
1 pc.
G.
Back Panel
1 pc.
H.
Door
1 pc.
I.
Door
1 pc.
J.
Shelf
1 pc.
K.
Shelf
2 pcs.
L.
Foot
4 pcs.
Adjustable Pin
12 pcs. (+1 extra)
Cam Lock Screw
8 pcs. (+1 extra)
Cam Lock
8 pcs. (+2 extra)
Small Hex Wrench
1 pc.
Hex Wrench
1 pc.
Flat Washer
16 pcs. (+1 extra)
M3.5x15
Washer Screw
6 pcs. (+1 extra)
M6x40
Head Cap Bolt (long)
8 pcs. (+1 extra)
M6x30
Head Cap Bolt
8 pcs. (+1 extra)
Handle
2 pcs.
M4x25
Machine Screw
4 pcs.
Spring Washer
16 pcs. (+1 extra)

Assembly Instructions 2/5
IMPORTANT
Use a soft cloth between these parts and the floor.
Do not use power tools above 8 volts to assemble.
Do not tighten all the bolts until each part is properly assembled.
The unit must be level to work properly. Use the included adjustable levelers to level.
Keep Hex Wrench as the bolts may need to be tightened in the future.
STEP 1
Place Top (A) and Bottom (B)
on a soft cloth.
Insert Cam Lock Screws into
pre-drilled holes in Top (A) and
Bottom (B), then tighten.
(See Figure 1)
Figure 1
B
Cam Lock Screw
A
STEP 2
Attach Feet (L) to
Bottom (B)
with Flat Washers,
Spring Washers and
Head Cap Bolts (long).
(See Figure 2)
Flat Washer
Spring Washer
Head Cap Bolt (long)
L
Figure 2
L
L
L
B

Assembly Instructions 3/5
Figure 4
Figure 3
STEP 4
Attach Middle Panels (E) and (F)
to unit with Cam Locks.
(See Figure 4)
STEP 3
Turn unit over to its’ upright position.
Attach Side Panels (C) and (D)
to unit with Flat Washers,
Spring Washers
and Head Cap Bolts.
(See Figure 3)
Slide Back Panel (G)
into position.
Head Cap Bolt
Spring Washer
Flat Washer
Cam Lock
F
E
D
C
G

Assembly Instructions 4/5
STEP 6
Insert Adjustable Pins into
side panels and middle panels
at desired level.
Place Shelves (J) and (K)
into position.
Level unit by adjusting
the adjustable levelers
on bottom of unit.
(See Figure 7)
Note: Unit must be level
to work properly.
STEP 5
Attach Top (A) to unit with Flat Washers,
Spring Washers, Head Cap Bolts and
Cam Locks.
Insert Washer Screws into
pre-drilled holes in unit,
then tighten.
Attach Doors (H) and (I) to unit
by sliding door hinges into
side panel hinges.
(See Figure 5)
Attach Handles to Doors (H) and (I)
with Machine Screws.
(See Figure 6)
Figure 6
Figure 5 Figure 7
K
J
Adjustable Pin
Flat Washer
Spring Washer
Head Cap Bolt
Washer Screw
H
A
Handle
Machine Screw
K
Cam Lock
I

Assembly Instructions 5/5
Drill 3/8” hole in wall
Top of unit
Hardware List
Anchor
1 pc. (+1 extra)
Bracket
2 pcs. (+1 extra)
Tip-over Restraint
1 pc. (+1 extra)
M3.5x40
Wall Screw
1 pc. (+1 extra)
M3.5x16
Wood Screw
1 pc. (+1 extra)
STEP 7
Place unit at desired location.
Drill a 3/8” hole in wall in-line with
pre-drilled hole at top of unit.
Move unit.
Insert Anchor into the wall hole
and attach Bracket with Wall Screw.
Attach Bracket at pre-drilled hole
at top of unit with Wood Screw.
Move unit back into place.
Slide Tip-over Restraint through
Bracket on wall and Bracket on unit.
(See Figure 8)
Put tie end of Tip-over Restraint into lock
end of Tip-over Restraint and pull until tight.
Figure 8
Wood Screw
Wall Screw
Bracket
on wall
Anchor in wall
3/8” wall hole
Pre-drilled hole
at top of unit
Tie end
Lock end
Bracket at
top of unit
Tip-over
Restraint
IMPORTANT
To help reduce the risk of the unit tipping over, the Tip-over Restraint must be installed following these instructions exactly.

NEVER
use glass cleaners on
finished furniture. Ammonia
chemically attacks the finish.
allow liquids to remain on furniture.
Absorption causes parts to warp
and split and finishes to delaminate.
NEVER
CARE INSTRUCTIONS
Do not use rubber
based placemats.
PREVENT
DISCOLORING
Do not use commercial
waxes and polishes.
PREVENT
YELLOWING
Do not place hot
objects on surface.
PREVENT
FINISH DAMAGE
Do not write
directly on surface.
PREVENT
MARKING
Do not use power tools
above 8 volts to assemble.
PREVENT
CRACKING
Do not place
in direct sunlight.
PREVENT
FADING
with a soft cloth moistened
in lukewarm soap and water.
Buff with a dry clean cloth.
CLEAN
Home Styles will provide replacements free of charge for missing or damaged hardware or parts within 30 days of
purchase. Digital images of the defective parts may be required. If the product was not purchased from an authorized
retail affiliate, Home Styles is under no obligation to provide replacement parts. Parts are not available for fully assembled
items nor are parts available for sale. Replacements for missing or damaged hardware or parts may be requested at:
www.homestyles-furniture.com/customer-service/replacement-parts
Home Styles Customer Service: www.homestyles-furniture.com,
[email protected], 888-680-7460, 877-831-0319