Home Styles 88 5053 106 User manual

Hardware List
Part List
Home Styles Customer Service: www.homestyles-furniture.com,
[email protected], 888-680-7460, 877-831-0319
Tool(s) required for assembly: Phillips screwdriver, Level, Drill (8 volts or less), 3/8” Drill Bit, Pencil
88 5053 106
Over Commode Stand
IMPORTANT
Carefully remove all the parts from the carton and
place them individually on a soft cloth to prevent
scratches or other damage.
Carefully and strictly follow these assembly instructions
to ensure a completed product as designed.
Do not use power tools above 8 volts to assemble.
Hex Wrench
1 pc.
Small Hex Wrench
1 pc.
M6x16
Head Cap Bolt
32 pcs. (+1 extra)
Spring Washer
32 pcs. (+1 extra)
Flat Washer
32 pcs. (+1 extra)
A.
Top
1 pc.
B.
Shelf
2 pcs.
C.
Shelf
1 pc.
D.
Side Frame
1 pc.
E.
Side Frame
1 pc.
F.
Side Frame
1 pc.
G.
Side Frame
1 pc.
H.
Front Stretcher
2 pcs.
I.
Back Stretcher
2 pcs.
Adjustable Pin
8 pcs. (+1 extra)
Steel Plate
2 pcs.

Assembly Instructions 2/4
IMPORTANT
Use a soft cloth between these parts and the floor.
Do not use power tools above 8 volts to assemble.
Do not tighten all the bolts until each part is properly assembled.
The unit must be level to work properly. Use the included adjustable levelers to level.
Keep Hex Wrench in a safe place as the bolts may need to be tightened up in the future.
STEP 1
Attach Side Frames (D) to Side Frame (F)
with Flat Washer, Spring Washer and
Head Cap Bolt, tightening the bolt
only half way. (See Figure 1)
Attach Steel Plates to Back Stretcher (I)
with Flat Washers, Spring Washers and
Head Cap Bolts. (See Figure 2)
Attach Front Stretchers (H) and
Back Stretchers (I) to unit with
Flat Washers, Spring Washers and
Head Cap Bolts, tightening the
bolts only half way. D
F
H
HI
I
Head Cap Bolt
Spring Washer
Flat Washer
Head Cap Bolt
Spring Washer
Flat Washer Steel Plate
G
E
STEP 2
Attach Side Frame (E) to Side Frame (G)
with Flat Washer, Spring Washer and
Head Cap Bolt, tightening the bolt only half way.
Attach unit to unit from Step 1 with Flat Washers, Spring Washers
and Head Cap Bolts, tightening the bolts only half way.
Head Cap Bolt
Spring Washer
Flat Washer
Figure 1 Figure 2

Assembly Instructions 3/4
STEP 3
Attach Top (A) and Shelf (C) to unit
with Flat Washers, Spring Washers
and Head Cap Bolts, tightening the
bolts only half way.
Tighten all Head Cap Bolts used in all steps. A
C
Head Cap Bolt
Spring Washer
Flat Washer
Adjustable Pin
B
B
STEP 4
Turn unit to its’ upright position.
Insert Adjustable Pins into unit at desired level.
(See Figure 3)
Place Shelves (B) into position.
Level unit by adjusting the adjustable levelers
on the bottom of unit. (See Figure 4)
Note: Unit must be level to work property.
Figure 3 Figure 4

Assembly Instructions 4/4
Hardware List
M3.5x40
Wall Screw
2 pcs. (+1 extra)
IMPORTANT
To help reduce the risk of the unit tipping over, the Tip-over Restraint must be installed following these instructions exactly.
Anchor
2 pcs. (+1 extra)
STEP 5
Place unit at desired location.
Loosen slightly the Head Cap Bolts attaching
Steel Plates to the unit, slide the Steel Plates
to the wall, then re-tighten the Head Cap Bolts.
Mark wall with pencil in the Steel Plates
screw holes. (See Figure 5)
Move unit.
Drill 3/8” holes in wall at pencil marks.
Insert Anchors into the wall holes.
Move unit back into place.
Attach Steel Plates to wall with Wall Screws.
(See Figure 6)
Drill 3/8” hole in wall
Drill 3/8” hole in wall
Wall Screw
Anchor in wall
3/8” wall hole
Steel Plate
Steel Plate
Pencil mark
Figure 6
Figure 5

NEVER
use glass cleaners on
finished furniture. Ammonia
chemically attacks the finish.
allow liquids to remain on furniture.
Absorption causes parts to warp
and split and finishes to delaminate.
NEVER
CARE INSTRUCTIONS
Do not use rubber
based placemats.
PREVENT
DISCOLORING
Do not use commercial
waxes and polishes.
PREVENT
YELLOWING
Do not place hot
objects on surface.
PREVENT
FINISH DAMAGE
Do not write
directly on surface.
PREVENT
MARKING
Do not use power tools
above 8 volts to assemble.
PREVENT
CRACKING
Do not place
in direct sunlight.
PREVENT
FADING
with a soft cloth moistened
in lukewarm soap and water.
Buff with a dry clean cloth.
CLEAN
Home Styles will provide replacements free of charge for missing or damaged hardware or parts within 30 days of
purchase. Digital images of the defective parts may be required. If the product was not purchased from an authorized
retail affiliate, Home Styles is under no obligation to provide replacement parts. Parts are not available for fully assembled
items nor are parts available for sale. Replacements for missing or damaged hardware or parts may be requested at:
www.homestyles-furniture.com/customer-service/replacement-parts
Home Styles Customer Service: www.homestyles-furniture.com,
[email protected], 888-680-7460, 877-831-0319