Home Styles 88 5053 95 User manual

Home Styles Consumer Assistance : www.homestyles-furniture.com,
[email protected], 888-680-7460, 877-831-0319
Hardware List
Part List
Carefully remove all the parts from the carton and put
them individually on a soft cloth to prevent scratches
or other damage occurring to the parts.
We have taken great care in the design of this
product and request that you carefully and strictly
follow our assembly instructions to ensure
a completed product as it was designed.
IMPORTANT NOTE
88 5053 95
Kitchen Cart
A.
Top
1 Pc.
B.
Side Frame
1 Pc.
C.
Side Frame
1 Pc.
D.
Top Frame
1 Pc.
E.
Fixed Shelf
1 Pc.
F.
Stretcher
2 Pcs.
K.
Basket
2 pcs.
(Please refer to the last page of these
instructions for drawer assembly steps.)
H.
Shelf
1 Pc.
I.
Base
1 Pc.
G.
Divider
1 Pc.
J.
Side Bar
2 Pcs.
Key Wrench
1 pc.
Hex Wrench
1 pc.
Small
Hex Wrench
1 pc.
Mx638
Head Cap Bolt
(long)
12 pcs. (+1 extra )
Mx616
Head Cap Bolt
22 pcs. (+1 extra )
Mx613
Head Cap Bolt
(For Basket)
16 pcs. (+1 extra )
Spring Washer
12 pcs. (+1 extra )
Flat Washer
12 pcs. (+1 extra )
Adjustable Pin
4 pcs. (+1 extra )
Caster
two lock
two non-lock
4 pcs.

Assembly Instructions 2/5
IMPORTANT
* Please keep Hex Wrench in a safe place as you may need to tighten up the Head Cap Bolts in the future.
* Do not tighten all the Head Cap Bolts until each part is properly assembled.
* Use a soft cloth between these parts and the floor.
Head Cap Bolt
Spring Washer
Flat Washer
Head Cap Bolt (long)
B
C
D
F
F
STEP 1
Attach Top Frame (D) and Stretchers (F) to Side Frame (B)
with Head Cap Bolts, Head Cap Bolts (long), Spring Washers
and Flat Washers, tightening the bolts only half way.
(See Figure 1)
Attach Side Frame (C) to unit with Head Cap Bolts, Head Cap Bolts (long), Spring Washers
and Flat Washers, tightening the bolts only half way.
Tighten all Head Cap Bolts.
STEP 2
Place Top (A) upside down on a soft cloth.
Attach unit to Top (A) with Head Cap Bolts.
Figure 1
Head Cap Bolt

Assembly Instructions 3/5
STEP 3
Attach Fixed Shelf (E)
to unit with Head Cap Bolts.
Slide Divider (G) into position and
attach to unit with Head Cap Bolts (long).
STEP 4
Attach Base (I) to unit
with Head Cap Bolts.
Insert Casters into the
pre-drilled holes of unit
with Key Wrench.
(See Figure 2)
Head Cap Bolt
Head Cap Bolt (long)
Head Cap Bolt (long)
G
E
I
Locking Caster
Head Cap Bolt
Figure 2

Assembly Instructions 4/5
STEP 5
Turn the unit over
to its’ upright position.
Insert Adjustable Pins into unit
at the desired level.
Place Shelf (H) into position.
STEP 6
Attach Side Bars (J) to unit with Head Cap Bolts (long),
Spring Washers and Flat Washers.
Slide Baskets (K) into position.
H
Adjustable Pin
Spring Washer
Flat Washer
Head Cap Bolt (long)
J
J
K
K

Assembly Instructions 5/5
Part List
Basket (K)
K1.
Basket Bottom
2 pcs.
K2.
Basket Side
4 pcs.
K3.
Basket Front
4 pcs.
STEP 1
Attach Basket Fronts (K3) to
Basket Bottom (K1) with clips.
(See Figure 1)
K1
K3
K3
STEP 2
Attach Basket Sides (K2) to unit
with clips and Head Cap Bolts for Basket.
(See Figure 2)
Figure 2
K2
K2
Head Cap Bolt
for Basket
Figure 1