Home Styles 20 05523 0095 User manual

Hardware List
Part List
Home Styles Customer Service: www.homestyles-furniture.com,
[email protected], 888-680-7460, 877-831-0319
Tool(s) required for assembly: Phillips screwdriver
20 05523 0095
Kitchen Cart
IMPORTANT
Carefully remove all the parts from the carton and
place them individually on a soft cloth to prevent
scratches or other damage.
Carefully and strictly follow these assembly instructions
to ensure a completed product as designed.
Do not use power tools above 8 volts to assemble.
M4x16
Wood Screw
for Caster
16 pcs. (+1 extra)
Caster
2 Locking
2 Non-Locking
4 pcs.
20 09100 Top carton is also needed for assembly.
B.
Side Panel
1 pc.
P.
Drawer
3 pcs.
Refer to later page(s) of these
instructions for drawer assembly.
C.
Middle Panel
1 pc.
F.
Back Upright
2 pcs.
A.
Side Panel
1 pc.
J.
Front Rail
1 pc.
M.
Door
1 pc.
D.
Middle Panel
1 pc.
E.
Back Panel
3 pcs.
I.
Side Bar
2 pcs.
H.
Shelf
4 pcs.
G.
Front Rail
1 pc.
L.
Back Rail
1 pc.
K.
Back Rail
1 pc.
Q.
Drawer
1 pc.
N.
Door
1 pc.
Hex Wrench
1 pc.
Small
Hex Wrench
1 pc.
Cam Lock
14 pcs. (+2 extra)
Cam Lock Screw
14 pcs. (+1 extra)
M3.5x25
Wood Screw (long)
32 pcs. (+1 extra)
M3.5x13
Wood Screw (short)
16 pcs. (+1 extra)
Adjustable Pin
16 pcs. (+2 extra)
Handle
4 pcs.
Knob
2 pcs.
M6x50
Head Cap Bolt
4 pcs. (+1 extra)
M4x20
Machine Screw
14 pcs.
Cross Dowel
4 pcs. (+1 extra)
M3.5x16
Wood Screw
for Back Panel
12 pcs. (+1 extra)
O.
Base
1 pc.

Assembly Instructions 2/10
IMPORTANT
Use a soft cloth between these parts and the floor.
Do not use power tools above 8 volts to assemble.
Do not tighten all the bolts until each part is properly assembled.
The unit must be level to work properly. Use the included adjustable levelers to level.
Keep Hex Wrench as the bolts may need to be tightened in the future.
STEP 1
Insert Cam Lock Screws into pre-drilled holes in Side Panels (A), (B), Middle Panels (C), (D),
Back Uprights (F) and Front Rail (J), then tighten. (See Figure 1)
C
A
D
B
Cam Lock Screw
J
Figure 1
F
F

Assembly Instructions 3/10
STEP 3
Attach Back Upright (F) to Middle Panel (D) with
Cam Locks, then attach to unit with Cam Lock.
J
K
F
B
D
STEP 2
Attach Front Rail (J) and
Back Rail (K) to Side Panel (B)
with Cam Locks.
(See Figure 2)
Cam Lock
Cam Lock
Figure 2

Assembly Instructions 4/10
F
G
E
C
E
E
STEP 5
Slide Back Panels (E) into position.
STEP 4
Attach Front Rail (G) to unit with
Cam Lock.
Attach Back Upright (F) to
Middle Panel (C) to unit with
Cam Locks, then attach to unit
with Cam Locks.
Cam Lock

Assembly Instructions 5/10
STEP 7
Attach Base (O) to unit with
Cross Dowels and Head Cap Bolts.
(See Figure 3)
Note: Arrow label indicates front
of unit.
STEP 6
Attach Back Rail (L) to unit
with Cam Lock.
Attach Side Panel (A) to
unit with Cam Locks.
O
L
A
Head Cap Bolt
Cross Dowel
Arrow label
Cam Lock
Figure 3

Assembly Instructions 6/10
STEP 8
Attach Casters to unit with
Wood Screws for Caster into
pre-drilled holes, with
Locking Casters at front.
(See Figure 4)
Note: Arrow label indicates front
of unit.
STEP 9
Insert Wood Screws for Back Panel
into pre-drilled holes in unit,
then tighten.
Wood Screw for Back Panel
Non-Locking Caster
Locking Caster
Arrow label
Figure 4
Wood Screw for Caster

Assembly Instructions 7/10
STEP 10
Insert Adjustable Pins into side panels and middle panels at desired level.
Place Shelves (H) into position.
Attach Doors (M) and (N) by sliding door hinges into side panel hinges.
(See Figure 5)
Attach Knobs to Doors (M) and (N) with Machine Screws.
(See Figure 6)
Attach Side Bar (I) to unit with Machine Screws.
(See Figure 7)
Attach Supports (V) to unit with Head Cap Bolts (middle).
I
M
N
H
V
H
H
H
I
V
Machine Screw
Knob
Machine Screw
Head Cap Bolt (middle)
Adjustable Pin
Figure 5
Figure 6 Figure 7

Part List
Assembly Instructions 8/10
STEP 13
Attach Handle with Machine Screws.
Drawer (P)
STEP 12
Slide Drawer Bottom (P5) into groove.
Attach Drawer Bottom (P5) to
unit with Wood Screws (short).
P1.
Drawer Front
3 pcs.
P5.
Drawer Bottom
3 pcs.
P3.
Drawer Side
3 pcs.
P4.
Drawer Side
3 pcs.
STEP 11
Attach Drawer Front (P1) and Drawer
Back (P2) to Drawer Side (P3)
with Wood Screws (long).
Attach Drawer Side (P4) to unit
with Wood Screws (long).
P5
Bottom
Wood Screw (long)
Machine Screw
Handle
Wood Screw (short)
Roller at back
P1
P3
P2 P4
P2.
Drawer Back
3 pcs.

Part List
Assembly Instructions 9/10
STEP 16
Attach Handle with Machine Screws.
Drawer (Q)
STEP 15
Slide Drawer Bottom (Q5) into groove.
Attach Drawer Bottom (Q5) to
unit with Wood Screws (short).
STEP 14
Attach Drawer Front (Q1) and Drawer
Back (Q2) to Drawer Side (Q3)
with Wood Screws (long).
Attach Drawer Side (Q4) to unit
with Wood Screws (long).
Q3
Q1
Q2 Q4
Q5
Bottom
Wood Screw (long)
Roller at back
Machine Screw
Handle
Wood Screw (short)
Q1.
Drawer Front
1 pc.
Q2.
Drawer Back
1 pc.
Q5.
Drawer Bottom
1 pc.
Q3.
Drawer Side
1 pc.
Q4.
Drawer Side
1 pc.

Assembly Instructions 10/10
STEP 17
Attach Top (W) to unit with Head Cap Bolts (middle).
Slide Drawers (P) and (Q) into position.
Head Cap Bolt (middle)
P
P
Q
W
P