Home Styles 5523-61 User manual

Hardware List
Part List
Tool(s) required for assembly: Phillips screwdriver, Level, Drill (8 volts or less), 3/8” Drill Bit
5523-61
Buffet
IMPORTANT
Cam Lock Screw
24 pcs. (+2 extra)
Magnet
2 pcs.
Carefully remove all the parts from the carton and
place them individually on a soft cloth to prevent
scratches or other damage.
Carefully and strictly follow these assembly instructions
to ensure a completed product as designed.
Do not use power tools above 8 volts to assemble.
Cam Lock
24 pcs. (+6 extra)
Adjustable Pin
16 pcs. (+1 extra)
M4x25
Machine Screw
6 pcs.
Handle
2 pcs.
Knob
2 pcs.
M3x16
Wood Screw
12 pcs. (+1 extra)
M3x25
Wood Screw (long)
16 pcs. (+1 extra)
M3x15
Wood Screw (short)
16 pcs. (+1 extra)
A.
Top
1 pc.
B.
Side Panel
1 pc.
C.
Side Panel
1 pc.
I.
Base
1 pc.
J.
Shelf
4 pcs.
K.
Door
1 pc.
L.
Door
1 pc.
M.
Drawer
2 pcs.
G.
Stretcher
2 pcs.
D.
Middle Panel
1 pc.
E.
Back Panel
3 pcs.
F.
Upright
2 pcs.
H.
Front Rail
1 pc.
Refer to later page(s) of these
instructions for drawer assembly.
Home Styles Customer Service: www.homestylesfurniture.com,
[email protected], 888-680-7460, 877-831-0319

Assembly Instructions 2/7
STEP 1
Insert Cam Lock Screws
into pre-drilled holes in Top (A),
Side Panels (B), (C) and Base (I),
then tighten. (See Figure 1)
STEP 2
Attach Stretcher (G) to Side Panel (B)
with Cam Lock. (See Figure 2)
Attach Uprights (F) to unit.
Slide Back Panels (E) into position.
Attach Stretcher (G) to unit with Cam Lock.
Figure 1
Cam Lock Screw
Cam Lock
IMPORTANT
Use a soft cloth between these parts and the floor.
Do not use power tools above 8 volts to assemble.
Do not tighten all the screws until each part is properly assembled.
The unit must be level to work properly. Use the included adjustable levelers to level.
Figure 2
A
C
B
I
EE
E
F
F
G
GB

Assembly Instructions 3/7
Magnet
Wood Screw (short)
Magnet
Cam Lock
STEP 3
Attach Magnets to
Front Rail (H) with
Wood Screws (short)
into pre-drilled holes.
(See Figure 3)
Attach Middle Panel (D),
Front Rail (H) and Side Panel (C)
to unit with Cam Locks.
STEP 4
Attach Base (I) to unit with Cam Locks.
Attach Top (A) to unit with Cam Locks.
Wood Screw (short)
Figure 3
Cam Lock
H
D
C
A
I

Assembly Instructions /47
Drawer (M)
M1.
Drawer Front
2 pcs.
M2.
Drawer Back
2 pcs.
M3.
Drawer Side
2 pcs.
M4.
Drawer Side
2 pcs.
M5.
Drawer Bottom
2 pcs.
Bottom
Wood Screw (long)
Part List
STEP 7
Attach Handle with Machine Screws.
STEP 5
Attach Drawer Front (M1)
and Drawer Back (M2) to
Drawer Side (M3) with Wood Screws (long).
Attach Drawer Side (M4) to unit with Wood Screws (long).
STEP 6
Slide Drawer Bottom (M5) into groove.
Attach Drawer Bottom (M5) to unit with
Wood Screws (short).
Roller at back
Wood Screw (short)
Machine Screw
Handle
M5
M3
M2
M1
Bottom
M4

Assembly Instructions 5/7
Figure 7
Figure 4 Figure 6
Figure 5
STEP 8
Insert Adjustable Pins into middle panel and side panels at desired level.
(See Figure 4)
Slide Drawers (M) and Shelves (J) into position.
Attach Doors (K) and (L) to unit by sliding door hinges into side panels hinges.
(See Figure 5)
Attach Knobs to Doors (K) and (L) with Machine Screws.
(See Figure 6)
Level unit by adjusting the adjustable levelers on bottom of unit.
(See Figure 7)
Knob
Machine Screw
Adjustable Pin
MM
L
K
J
JJ
J

Assembly Instructions /67
Wood Screw
Cam Lock
STEP 9
Insert Cam Locks into unit and tighten.
Insert Wood Screws into pre-drilled holes in unit, then tighten. (See Figure 8)
Note: Unit must be level before tightening these screws.
Figure 8

Assembly Instructions /77
Hardware List
STEP 10
Place unit at desired location.
Drill a 3/8” hole in wall in-line with
the pre-drilled hole at top of unit.
Move unit.
Insert Anchor into the wall hole
and attach Bracket with Wall Screw.
Attach Bracket at pre-drilled hole
at top of unit with Wood Screw.
Move unit back into place.
Slide Tipover Restraint through
Bracket on wall and Bracket on unit.
(See Figure 9)
Put tie end of Tipover Restraint into lock
end of Tipover Restraint and pull until tight.
Anchor
1 pc. (+1 extra)
Bracket
2 pcs. (+1 extra)
Tipover Restraint
1 pc. (+1 extra)
M3.5x40
Wall Screw
1 pc. (+1 extra)
M3.5x16
Wood Screw
1 pc. (+1 extra)
Drill 3/8” hole in wall
Top of unit
IMPORTANT
To help reduce the risk of the unit tipping over, the Tipover Restraint must be installed following these instructions exactly.
Bracket
on wall
Anchor in wall
3/8” wall hole
Tie end
Lock end
Bracket at
top of unit
Tipover
Restraint
Figure 9
Wood Screw
Wall Screw Pre-drilled hole
at top of unit

NEVER
use glass cleaners on
finished furniture. Ammonia
chemically attacks the finish.
allow liquids to remain on furniture.
Absorption causes parts to warp
and split and finishes to delaminate.
NEVER
CARE INSTRUCTIONS
Do not use rubber
based placemats.
PREVENT
DISCOLORING
Do not use commercial
waxes and polishes.
PREVENT
YELLOWING
Do not place hot
objects on surface.
PREVENT
FINISH DAMAGE
Do not write
directly on surface.
PREVENT
MARKING
Do not use power tools
above 8 volts to assemble.
PREVENT
CRACKING
Do not place
in direct sunlight.
PREVENT
FADING
with a soft cloth moistened
in lukewarm soap and water.
Buff with a dry clean cloth.
CLEAN
Home Styles will provide replacements free of charge for missing or damaged hardware or parts within 30 days of
purchase. Digital images of the defective parts may be required. If the product was not purchased from an authorized
retail affiliate, Home Styles is under no obligation to provide replacement parts. Parts are not available for fully assembled
items nor are parts available for sale. Replacements for missing or damaged hardware or parts may be requested at:
www.homestylesfurniture.com/customer-service/replacement-parts
Home Styles Customer Service: www.homestylesfurniture.com,
[email protected], 888-680-7460, 877-831-0319