Home Styles Corner Entertainment 20 05503 0071 User manual

Hardware List
Part List
Home Styles Customer Service: www.homestyles-furniture.com,
[email protected], 888-680-7460, 877-831-0319
Tool(s) required for assembly: Phillips screwdriver, Level
IMPORTANT
Carefully remove all the parts from the carton and
place them individually on a soft cloth to prevent
scratches or other damage.
Carefully and strictly follow these assembly instructions
to ensure a completed product as designed.
Do not use power tools above 8 volts to assemble.
Corner Entertainment
20 05503 0071
Carton 20 05503 0072 is also needed for assembly.
B.
Base
1 pc.
A.
Top
1 pc.
Hex Wrench
1 pc.
Small Hex Wrench
1 pc.
Adjustable Pin
24 pcs. (+1 extra)
M4x25
Machine Screw
2 pcs.
M3x15
Wood Screw
4 pcs. (+1 extra)
Magnet
2 pcs.
M6x32
Head Cap Bolt
7 pcs. (+1 extra)
Cam Lock
19 pcs. (+4 extra)
Cam Lock Screw
19 pcs. (+1 extra)
Spring Washer
7 pcs. (+1 extra)
Flat Washer
7 pcs. (+1 extra)
Knob
2 pcs.
M5x32
Wood Screw
for Back Panel
6 pcs. (+1 extra)

Assembly Instructions 2/7
IMPORTANT
Use a soft cloth between these parts and the floor.
Do not use power tools above 8 volts to assemble.
Do not tighten all the bolts until each part is properly assembled.
The unit must be level to work properly. Use the included adjustable levelers to level.
Keep Hex Wrench as the bolts may need to be tightened in the future.
C
C
B
STEP 1
Place Base (B) upside down
on a soft cloth.
Attach Feet (C) to Base (B).
Figure 2
Figure 1
STEP 2
Place Top (A), Base (B)
on a soft cloth.
Insert Cam Lock Screws into
pre-drilled holes in Top (A),
Base (B), then tighten.
(See Figure 1)
Attach Magnets to Top (A) by
inserting Wood Screws into
pre-drilled holes, then tighten.
(See Figure 2)
A
B
Cam Lock Screw
Wood Screw
Magnet

Assembly Instructions 3/7
B
M
STEP 3
Attach Back Panel (M) to Base (B) with Flat Washers,
Spring Washers and Head Cap Bolts. (See Figure 3)
Flat Washer
Spring Washer
Head Cap Bolt
Figure 3
Wood Screw for Back Panel
Figure 4
Figure 5
STEP 4
Attach Middle Panels (H) and (I) to unit with Cam Locks and Wood Screws for Back Panel.
(See Figures 4 and 5)
HI
Cam Lock

Assembly Instructions 4/7
G
Head Cap Bolt
Spring Washer
Flat Washer
F
STEP 5
Attach Side Panels (F) and (G)
to unit with Flat Washers,
Spring Washers and Head Cap Bolts.
STEP 6
Attach Back Panels (J) and (K)
to unit with Cam Locks.
K
Cam Lock
J
STEP 7
Attach Back Panel (L) to unit
with Wood Screws for Back Panel.
L
Wood Screw for Back Panel

Assembly Instructions 5/7
Figure 7
STEP 8
Attach Doors (N) and (O) to unit by sliding
door hinges into side panel hinges. (See Figure 6)
Attach Knobs to Doors (N) and (O)
with Machine Screws. (See Figure 7)
Figure 6
Machine Screw
Knob
N
O
STEP 9
Insert Adjustable Pins into side panels, middle panels
and back panels at desired level. (See Figure 8)
Place Shelves (D) and (E) into position.
D
DD
D
E
E
Adjustable Pin
Figure 8

Assembly Instructions 6/7
Figure 9
Cam Lock
Head Cap Bolt
Spring Washer
Flat Washer
STEP 10
Attach Top (A) to unit with Flat Washers,
Spring Washers, Head Cap Bolts and Cam Locks.
Level unit by adjusting the adjustable levelers on bottom of unit.
(See Figure 9)
Note: Unit must be level to work properly.
A

Assembly Instructions 7/7
Hardware List
IMPORTANT
To help reduce the risk of the unit tipping over, the Tipover Restraints must be installed following these instructions exactly.
Anchor
2 pcs. (+1 extra)
Bracket
4 pcs. (+1 extra)
Tipover Restraint
2 pcs. (+1 extra)
M3.5x40
Wall Screw
2 pcs. (+1 extra)
M3.5x16
Wood Screw
2 pcs. (+1 extra)
STEP 11
Place unit at desired location.
Drill a 3/8” holes in wall in-line with
pre-drilled holes at top of unit.
Move unit.
Insert Anchors into the wall hole
and attach Brackets with Wall Screws.
Attach Brackets at pre-drilled holes
at top of unit with Wood Screws.
Move unit back into place.
Slide Tipover Restraints through
Brackets on wall and Brackets on unit.
(See Figure 10)
Put tie end of Tipover Restraints into lock
end of Tipover Restraints and pull until tight.
Bracket
on wall
Anchor in wall
3/8” wall hole
Tie end
Lock end
Bracket at
top of unit
Tipover
Restraint
Figure 10
Wood Screw
Wall Screw Pre-drilled hole
at top of unit
Drill 3/8” hole in wall
Top of unit

NEVER
use glass cleaners on
finished furniture. Ammonia
chemically attacks the finish.
allow liquids to remain on furniture.
Absorption causes parts to warp
and split and finishes to delaminate.
NEVER
CARE INSTRUCTIONS
Do not use rubber
based placemats.
PREVENT
DISCOLORING
Do not use commercial
waxes and polishes.
PREVENT
YELLOWING
Do not place hot
objects on surface.
PREVENT
FINISH DAMAGE
Do not write
directly on surface.
PREVENT
MARKING
Do not use power tools
above 8 volts to assemble.
PREVENT
CRACKING
Do not place
in direct sunlight.
PREVENT
FADING
with a soft cloth moistened
in lukewarm soap and water.
Buff with a dry clean cloth.
CLEAN
Home Styles will provide replacements free of charge for missing or damaged hardware or parts within 30 days of
purchase. Digital images of the defective parts may be required. If the product was not purchased from an authorized
retail affiliate, Home Styles is under no obligation to provide replacement parts. Parts are not available for fully assembled
items nor are parts available for sale. Replacements for missing or damaged hardware or parts may be requested at:
www.homestyles-furniture.com/customer-service/replacement-parts
Home Styles Customer Service: www.homestyles-furniture.com,
[email protected], 888-680-7460, 877-831-0319