Home Styles 5061-941 User manual

Part List
5061-941
Kitchen Island
IMPORTANT
Carefully remove all the parts from the carton and
place them individually on a soft cloth to prevent
scratches or other damage.
Carefully and strictly follow these assembly instructions
to ensure a completed product as designed.
Do not use power tools above 8 volts to assemble.
A.
Top
1 pc.
For assembly see instructions in carton 5060 942.-
Care Instructions
Hardware List
Hex Wrench
1 pc.
Small Hex Wrench
1 pc.
Flat Washer
10 pcs. (+1 extra)
M6x25
Head Cap Bolt
10 pcs. (+1 extra)
Spring Washer
10 pcs. (+1 extra)
This solid wood top cannot be used as a cutting or chopping board.
Do not use knives or any sharp objects directly on the top.
Follow the Care Instructions on the last page of the
5060 942 Kitchen Island Assembly Instructions.-
styles Customer Service: www.homestylesfurniture.com,home
[email protected], 888-680-7460

Hardware List
Part List
Tool(s) required for assembly: Level
C.
Shelf
1 pc.
D.
Shelf
1 pc.
E.
Support
4 pcs.
F.
Post
4 pcs.
B.
Apron
1 pc.
5060-942
Kitchen Island
IMPORTANT
Carton 5060 94Q1, 5061 941 or 5064 941 is also needed for assembly.-- -
Hex Wrench
1 pc.
Small Hex Wrench
1 pc.
Carefully remove all the parts from the carton and
place them individually on a soft cloth to prevent
scratches or other damage.
Carefully and strictly follow these assembly instructions
to ensure a completed product as designed.
Do not use power tools above 8 volts to assemble.
M6x19
Head Cap Bolt (short)
28 pcs. (+1 extra)
Spring Washer
14 pcs. (+1 extra)
Flat Washer
14 pcs. (+1 extra)
M6x32
Head Cap Bolt (long)
4 pcs. (+1 extra)
M6x19
Head Cap Bolt
14 pcs. (+1 extra)
styles Customer Service: www.homestylesfurniture.com,home
[email protected], 888-680-7460

Assembly Instructions 2/4
IMPORTANT
Use a soft cloth between these parts and the floor.
Do not use power tools above 8 volts to assemble.
Do not tighten all the bolts until each part is properly assembled.
The unit must be level to work properly. Use the included adjustable levelers to level.
Keep Hex Wrench as the bolts may need to be tightened in the future.
Figure 1 Figure 3Figure 2
STEP 1
Place Top (A) upside down on a soft cloth.
Attach Apron (B) to Top (A) with
Flat Washers, Spring Washers and
Head Cap Bolts, tightening bolts
only halfway. (See Figure 1)
Tighten all bolts used in this step.
Head Cap Bolt
Spring Washer
Flat Washer
A
STEP 2
Attach Supports (E) to unit with
Flat Washers, Spring Washers
and Head Cap Bolts,
tightening bolts only halfway.
(See Figure 2)
Attach Shelf (C) to unit with
Head Cap Bolts (long),
tightening bolts only halfway.
(See Figure 3)
Head Cap Bolt (long)
Spring Washer
Flat Washer
Head Cap Bolt
E
E
E
E
B
C

Assembly Instructions /34
Figure 4 Figure 5
Head Cap Bolt (short)
Head Cap Bolt (short)
STEP 3
Attach Posts (F) to unit with Head Cap Bolts (short),
tightening bolts only halfway. (See Figures 4 and 5)
STEP 4
Attach Shelf (D) to unit with Head Cap
Bolts (short), tightening bolts only halfway.
F
F
D

Assembly Instructions /44
STEP 6
Turn unit over to its upright position.
Level unit by adjusting the adjustable
levelers on bottom of unit. (See Figure 6)
Note: Unit must be level to work properly.
Figure 6
Head Cap Bolt (short)
F
STEP 5
Attach Posts (F) to unit with
Head Cap Bolts (short),
tightening bolts only halfway.
Tighten all bolts used in Steps 2, 3, 4 and 5.
F

NEVER
use glass cleaners on
finished furniture. Ammonia
chemically attacks the finish.
allow liquids to remain on furniture.
Absorption causes parts to warp
and split and finishes to delaminate.
NEVER
CARE INSTRUCTIONS
Do not use rubber
based placemats.
PREVENT
DISCOLORING
Do not use commercial
waxes and polishes.
PREVENT
YELLOWING
Do not place hot
objects on surface.
PREVENT
FINISH DAMAGE
Do not write
directly on surface.
PREVENT
MARKING
Do not use power tools
above 8 volts to assemble.
PREVENT
CRACKING
Do not place
in direct sunlight.
PREVENT
FADING
with a soft cloth moistened
in lukewarm soap and water.
Buff with a dry clean cloth.
CLEAN
homestyles will provide replacements free of charge for missing or damaged parts within 1 year of purchase.
Digital images of the defective parts may be required. If the product was not purchased from an authorized retailer,
homestyles is under no obligation to provide replacement parts. Parts are not available for fully assembled items nor
are parts available for sale. Replacements for missing or damaged parts may be requested via contact info below.
styles Customer Service: www.homestylesfurniture.com,home
[email protected], 888-680-7460
NEVER
use glass cleaners on
finished furniture. Ammonia
chemically attacks the finish.
allow liquids to remain on furniture.
Absorption causes parts to warp
and split and finishes to delaminate.
NEVER
CARE INSTRUCTIONS
Do not use rubber
based placemats.
PREVENT
DISCOLORING
Do not use commercial
waxes and polishes.
PREVENT
YELLOWING
Do not place hot
objects on surface.
PREVENT
FINISH DAMAGE
Do not write
directly on surface.
PREVENT
MARKING
Do not use power tools
above 8 volts to assemble.
PREVENT
CRACKING
Do not place
in direct sunlight.
PREVENT
FADING
with a soft cloth moistened
in lukewarm soap and water.
Buff with a dry clean cloth.
CLEAN
homestyles will provide replacements free of charge for missing or damaged parts within 1 year of purchase.
Digital images of the defective parts may be required. If the product was not purchased from an authorized retailer,
homestyles is under no obligation to provide replacement parts. Parts are not available for fully assembled items nor
are parts available for sale. Replacements for missing or damaged parts may be requested via contact info below.
styles Customer Service: www.homestylesfurniture.com,home
[email protected], 888-680-7460