Home Styles 5050-22 User manual

M4x12
Wood Screw
6 pcs. (+1 extra)
Flat Washer
8 pcs. (+1 extra)
Spring Washer
8 pcs. (+1 extra)
Hardware List
Part List
Tool(s) required for assembly: Phillips screwdriver, Level
5050-22
IMPORTANT
Carefully remove all the parts from the carton and
place them individually on a soft cloth to prevent
scratches or other damage.
Carefully and strictly follow these assembly instructions
to ensure a completed product as designed.
Do not use power tools above 8 volts to assemble.
Console Table
C.
Side Frame
2 pcs.
B.
Stretcher
2 pcs.
A.
Cabinet
1 pc.
D.
Shelf
1 pc.
M6x12
Head Cap Bolt
8 pcs. (+1 extra)
styles Customer Service: www.homestylesfurniture.com,home
[email protected], 888-680-7460
Small
Hex Wrench
1 pc.
Hex Wrench
1 pc.

Assembly Instructions 2/4
IMPORTANT
Use a soft cloth between these parts and the floor.
Do not use power tools above 8 volts to assemble.
Do not tighten all the bolts until each part is properly assembled.
Keep Hex Wrench as the bolts may need to be tightened in the future.
STEP 1
Attach Stretchers (B)
and Shelf (D) to Side Frames (C)
with Head Cap Bolts, Spring Washers and
Flat Washers, tightening bolts only halfway.
(See Figure 1)
Tighten all bolts used in this step.
Flat Washer
Spring Washer
Head Cap Bolt
A
Figure 1
Drawer Stop
STEP 2
Remove drawers from Cabinet (A).
Rotate drawer stops into position.
(See Figure 2)
Figure 2
C
B
B
C
D

Machine Screw
Handle
Assembly Instructions 3/4
Wood Screw
STEP 3
Place Cabinet (A) upside down
on a soft cloth.
Attach unit from Step 1 to
Cabinet (A) with Wood Screws.
STEP 4
Turn unit over to its upright position.
Remove handles on inside of drawers and attach to outside of drawers with machine screws.
Slide drawers into position.
A

Hardware List
Assembly Instructions 4/4
STEP 5
Place unit at desired location.
Drill a 3/8” hole in wall in-line with bottom
of back center upright of unit.
Move unit.
Insert Anchor into the wall hole
and attach Bracket with Wall Screw.
Move unit back into place.
Slide Tipover Restraint through
Bracket on wall and around
back center upright of unit.
(See Figure 4)
Put tie end of Tipover Restraint
into lock end of Tipover Restraint
and pull until tight.
Figure 4
Wall Screw
Bracket
on wall
Anchor in wall
3/8” wall hole
Tie end Lock end
Tipover
Restraint
Back center
upright
IMPORTANT
To help reduce the risk of the unit tipping over, the Tipover Restraint must be installed following these instructions exactly.
Anchor
1 pc. (+1 extra)
Tipover Restraint
1 pc. (+1 extra)
M3.5x40
Wall Screw
1 pc. (+1 extra)
Drill 3/8” hole in wall
Back center upright
Bracket
1 pc. (+1 extra)

NEVER
use glass cleaners on
finished furniture. Ammonia
chemically attacks the finish.
allow liquids to remain on furniture.
Absorption causes parts to warp
and split and finishes to delaminate.
NEVER
CARE INSTRUCTIONS
Do not use rubber
based placemats.
PREVENT
DISCOLORING
Do not use commercial
waxes and polishes.
PREVENT
YELLOWING
Do not place hot
objects on surface.
PREVENT
FINISH DAMAGE
Do not write
directly on surface.
PREVENT
MARKING
Do not use power tools
above 8 volts to assemble.
PREVENT
CRACKING
Do not place
in direct sunlight.
PREVENT
FADING
with a soft cloth moistened
in lukewarm soap and water.
Buff with a dry clean cloth.
CLEAN
homestyles will provide replacements free of charge for missing or damaged parts within 1 year of purchase.
Digital images of the defective parts may be required. If the product was not purchased from an authorized retailer,
homestyles is under no obligation to provide replacement parts. Parts are not available for fully assembled items nor
are parts available for sale. Replacements for missing or damaged parts may be requested via contact info below.
styles Customer Service: www.homestylesfurniture.com,home
[email protected], 888-680-7460