Home Styles 5033-89 User manual

Hardware List
Part List
Tool(s) required for assembly: Phillips screwdriver
D.
Back Frame
1 pc.
E.
Side Stretcher
1 pc.
B.
Leg
1 pc.
C.
Leg
1 pc.
A.
Seat
1 pc.
5033-89
Bar Stool
IMPORTANT
Carefully remove all the parts from the carton and
place them individually on a soft cloth to prevent
scratches or other damage.
Carefully and strictly follow these assembly instructions
to ensure a completed product as designed.
Do not use power tools above 8 volts to assemble.
F.
Side Stretcher
1 pc.
G.
Front Stretcher
1 pc.
styles Customer Service: www.homestylesfurniture.com,home
[email protected], 888-680-7460
M8x76
Head Cap Bolt (long)
4 pcs. (+1 extra)
M8x35
Head Cap Bolt (short)
1 pc. (+1 extra)
M8x57
Head Cap Bolt
4 pcs. (+1 extra)
Flat Washer
9 pcs. (+1 extra)
Spring Washer
9 pcs. (+1 extra)
M3.5x40
Wood Screw
6 pcs. (+1 extra)
Hex Wrench
1 pc.
Small Hex Wrench
1 pc.

Assembly Instructions 2/3
IMPORTANT
Use a soft cloth between these parts and the floor.
Do not use power tools above 8 volts to assemble.
Make sure unit is level before tightening these screws.
Do not tighten all the bolts until each part is properly assembled.
Keep Hex Wrench as the bolts may need to be tightened in the future.
Wood Screw
Arrow label at front
Head Cap Bolt
Spring Washer
Flat Washer
F
E
A
B
C
G
Figure 1 STEP 1
Place Seat (A) upside down on a soft cloth.
Attach Legs (B) and (C) to Seat (A) with Flat Washers,
Spring Washers and Head Cap Bolts,
tightening bolts only halfway.
(See Figure 1)
Attach Stretcher (G) to unit with Wood Screws.
(See Figure 2)
Orientate Stretcher (E) so Arrow label is at front of unit,
then attach Stretcher (E) to Leg (B) with Wood Screw.
(See Figure 3)
Orientate Stretcher (F) so Arrow label is at front of unit,
then attach Stretcher (F) to Leg (C) with Wood Screw.
Figure 2
Figure 3

Assembly Instructions 3/3
Flat Washer
Spring Washer
Head Cap Bolt (short)
Head Cap Bolt (long)
Spring Washer
Flat Washer
Wood Screw
D
STEP 2
Attach Back Frame (D) to unit with Flat Washers, Spring Washers,
Head Cap Bolts (short) and Head Cap Bolts (long),
tightening bolts only halfway.
(See Figures 4 and 5)
Tighten all bolts used in Steps 1 and 2.
Insert Wood Screws into pre-drilled holes in unit, then tighten.
Figure 5
Figure 4

NEVER
use glass cleaners on
finished furniture. Ammonia
chemically attacks the finish.
allow liquids to remain on furniture.
Absorption causes parts to warp
and split and finishes to delaminate.
NEVER
CARE INSTRUCTIONS
Do not use rubber
based placemats.
PREVENT
DISCOLORING
Do not use commercial
waxes and polishes.
PREVENT
YELLOWING
Do not place hot
objects on surface.
PREVENT
FINISH DAMAGE
Do not write
directly on surface.
PREVENT
MARKING
Do not use power tools
above 8 volts to assemble.
PREVENT
CRACKING
Do not place
in direct sunlight.
PREVENT
FADING
with a soft cloth moistened
in lukewarm soap and water.
Buff with a dry clean cloth.
CLEAN
homestyles will provide replacements free of charge for missing or damaged parts within 30 days of purchase.
Digital images of the defective parts may be required. If the product was not purchased from an authorized retailer,
homestyles is under no obligation to provide replacement parts. Parts are not available for fully assembled items nor
are parts available for sale. Replacements for missing or damaged parts may be requested via contact info below.
styles Customer Service: www.homestylesfurniture.com,home
[email protected], 888-680-7460