Home Styles 9100-101 User manual

IMPORTANT
Carefully remove all the parts from the carton and
place them individually on a soft cloth to prevent
scratches or other damage.
Carefully and strictly follow these assembly instructions
to ensure a completed product as designed.
Do not use power tools above 8 volts to assemble.
Hardware List
Part List
For assembly see instructions in Cart carton.
W.
Top
1 pc.
V.
Support
2 pcs.
9100-101
Solid Wood Top
M6x30
Head Cap Bolt (middle)
6 pcs. (+1 extra)
styles Customer Service: www.homestylesfurniture.com,home
[email protected], 888-680-7460

Part List
Tool(s) required for assembly: Phillips screwdriver
9100-006
Kitchen Cart
IMPORTANT
Carefully remove all the parts from the carton and
place them individually on a soft cloth to prevent
scratches or other damage.
Carefully and strictly follow these assembly instructions
to ensure a completed product as designed.
Do not use power tools above 8 volts to assemble.
9100 Top carton is also needed for assembly.
J.
Base
1 pc.
A.
Side Panel
1 pc.
B.
Side Panel
1 pc.
G.
Back Rail
1 pc.
H.
Front Rail
1 pc.
N.
Door
1 pc.
O.
Door
1 pc.
T.
Drawer
3 pcs.
U.
Drawer
1 pc.
Refer to later page(s) of these
instructions for drawer assembly.
M.
Arm
1 pc.
R.
Rack Base
1 pc.
S.
Pipe
3 pcs.
K.
Shelf
2 pcs.
P.
Rack Side
1 pc.
Q.
Rack Side
1 pc.
L.
Arm Handle
2 pcs.
C.
Middle Panel
1 pc.
D.
Middle Panel
1 pc.
E.
Back Panel
3 pcs.
I.
Front Rail
3 pcs.
F.
Back Upright
2 pcs.
styles Customer Service: www.homestylesfurniture.com,home
[email protected], 888-680-7460
Hardware List
Hex Wrench
1 pc.
Small Hex Wrench
1 pc.
Caster
2 Locking
2 Non-Locking
4 pcs.
M3.5x13
Wood Screw (short)
24 pcs. (+1 extra)
Adjustable Pin
81pcs. (+ extra)
M x164
Wood Screw
16 pcs. (+1 extra)
Handle
4 pcs.
Wood Plug
10 pcs. (+1 extra)
M6x35
Head Cap Bolt
14 pcs. (+1 extra)
M4x25
Machine Screw
10 pcs.
M3.5x25
Wood Screw (long)
32 pcs. (+1 extra)
Knob
2 pcs.

Assembly Instructions 2/8
IMPORTANT
Use a soft cloth between these parts and the floor.
Do not use power tools above 8 volts to assemble.
Do not tighten all the bolts until each part is properly assembled.
Keep Hex Wrench as the bolts may need to be tightened in the future.
STEP 2
Attach lower Front Rail (I) to unit.
Attach middle Front Rail (I) to unit.
Attach upper Front Rail (I) to unit.
Slide Back Panels (E) into position.
Head Cap Bolt
STEP 1
Attach Side Panel (A) to Base (J) with
Head Cap Bolts. (See Figure 1)
Attach Back Upright (F) to Middle Panel (C),
then attach to unit.
Attach Back Upright (F) to Middle Panel (D),
then attach to unit.
Note: Assemble so Arrow labels
on Back Uprights (F) point
to each other.
Arrow labels point to each other
Figure 1
CD
J
F
E
F
A
E
I
I
I
E

Assembly Instructions 3/8
STEP 4
Turn unit upside down.
Attach Casters to unit with
Wood Screws into pre-drilled holes,
with Locking Casters at front.
(See Figure 2)
Note: Arrow label indicates front of unit.
Figure 2
STEP 3
Attach Back Rail (G) and
Front Rail (H) to unit with
Head Cap Bolts.
Note: Arrow label indicates
front of Back Rail (G).
Attach Side Panel (B) to
unit with Head Cap Bolts.
Arrow label at front
Wood Screw
Non-Locking Caster
Locking Caster
Arrow label at front
Head Cap Bolt
H
B
G

Assembly Instructions 4/8
Figure 4
Figure 3
STEP 5
Turn unit over to its upright position.
Attach Rack Side (P) to unit with Head Cap Bolt. (See Figure 3)
Slide Rack Base (R) and Pipes (S) into Rack Side (P).
Attach Rack Side (Q) to unit with Head Cap Bolt.
Attach Arm Handles (L) to unit with Head Cap Bolts. (See Figure 4)
Slide Arm (M) into position.
PL
Head Cap Bolt
S
Q
L
R
M
L
P

Assembly Instructions 5/8
Head Cap Bolt (middle)
Adjustable Pin
Knob
Machine Screw
STEP 6
Insert Adjustable Pins into side panels and middle panels at desired level.
(See Figure 5)
Place Shelves (K) into position.
Attach Doors (N) and (O) to unit by sliding door hinges into side panel hinges.
(See Figure 6)
Attach Knobs to Doors (N) and (O) with Machine Screws.
(See Figure 7)
Attach Supports (V) to unit with Head Cap Bolts (middle).
Note: Supports (V) and Head Cap Bolts (middle) are in 9100 Top carton.
Figure 5 Figure 7Figure 6
K
K
NV
O
V

Part List
Assembly Instructions 6/8
STEP 9
Attach Handle with Machine Screws.
T1.
Drawer Front
3 pcs.
T2.
Drawer Back
3 pcs.
T5.
Drawer Bottom
3 pcs.
Wood Screw (short)
Drawer (T)
T3.
Drawer Side
3 pcs.
T4.
Drawer Side
3 pcs.
STEP 7
Attach Drawer Front (T1) and Drawer
Back (T2) to Drawer Side (T3)
with Wood Screws (long).
Attach Drawer Side (T4) to unit
with Wood Screws (long).
Wood Screw (long)
Bottom
STEP 8
Slide Drawer Bottom (T5) into groove.
Attach Drawer Bottom (T5) to
unit with Wood Screws (short).
Bottom Bottom
T5
Roller at back
Machine Screw
Handle
BottomBottom
T4
T1
T3
T2

Part List
Assembly Instructions 7/8
STEP 12
Attach Handle with Machine Screws.
U1.
Drawer Front
1 pc.
U2.
Drawer Back
1 pc.
U5.
Drawer Bottom
1 pc.
STEP 10
Attach Drawer Front (U1) and Drawer
Back (U2) to Drawer Side (U3)
with Wood Screws (long).
Attach Drawer Side (U4) to unit
with Wood Screws (long).
Drawer (U)
STEP 11
Slide Drawer Bottom (U5) into groove.
Attach Drawer Bottom (U5) to
unit with Wood Screws (short).
U3.
Drawer Side
1 pc.
U4.
Drawer Side
1 pc.
Bottom Bottom
Bottom Bottom
Wood Screw (long)
Bottom
U2
U3
U4
Roller at back
U1
Wood Screw (short)
U5
Machine Screw
Handle

Assembly Instructions 8/8
STEP 13
Attach Top (W) to unit with
Head Cap Bolts (middle).
Slide Drawers (T) and (U)
into position.
Head Cap Bolt (middle)
STEP 14
Cover all holes
with Wood Plugs.
(See Figure 8)
Figure 8
Wood Plug
T
U
T
W
T

NEVER
use glass cleaners on
finished furniture. Ammonia
chemically attacks the finish.
allow liquids to remain on furniture.
Absorption causes parts to warp
and split and finishes to delaminate.
NEVER
CARE INSTRUCTIONS
Do not use rubber
based placemats.
PREVENT
DISCOLORING
Do not use commercial
waxes and polishes.
PREVENT
YELLOWING
Do not place hot
objects on surface.
PREVENT
FINISH DAMAGE
Do not write
directly on surface.
PREVENT
MARKING
Do not use power tools
above 8 volts to assemble.
PREVENT
CRACKING
Do not place
in direct sunlight.
PREVENT
FADING
with a soft cloth moistened
in lukewarm soap and water.
Buff with a dry clean cloth.
CLEAN
homestyles will provide replacements free of charge for missing or damaged parts within 30 days of purchase.
Digital images of the defective parts may be required. If the product was not purchased from an authorized retailer,
homestyles is under no obligation to provide replacement parts. Parts are not available for fully assembled items nor
are parts available for sale. Replacements for missing or damaged parts may be requested via contact info below.
styles Customer Service: www.homestylesfurniture.com,home
[email protected], 888-680-7460