Home Styles 88 5516 991 User manual

Home Styles ConsumerAssistance: www.homestyles-furniture.com,
[email protected], 888-680-7460, 877-831-0319
Tools required for assembly : Phillips screwdriver Tools recommended for assembly : Level
Part List
IMPORTANT NOTE
Carefully remove all the parts from the carton and put
them individually on a soft cloth to prevent scratches
or other damages occuring to the wood parts.
We have taken great care in the design of this
product and request that you carefully and strictly
follow our assembly instructions to ensure a
completed product as it was designed.
For assembly also need the following : 88 5516 992
Hardware List
D.
Shelf
2 pcs.
B.
Middle Panel
1 pc.
G.
Foot Rest Support
2 pcs.
Adjustable Pin
12 pcs. (+1 extra)
A.
Top
1 pc.
E.
Door
1 pc.
Hex Wrench
1 pc.
Small
Hex Wrench
1 pc. Cam Lock
19 pcs. (+4 extra)
M4x16
Wood Screw (short)
8 pcs. (+1 extra) Magnet
1 pc.
M4x25
Wood Screw (long)
for drawer side
8 pcs. (+1 extra)
Cam Lock Screw
19 pcs. (+2 extra)
Pull Handle
1 pc.
M6x30
Head Cap Bolt
8 pcs. (+1 extra)
88 5516 991
Barnside Bar
C.
Shelf
1 pc.
F.
Foot Rest
1 pc.
Knob
1 pc.
Mt
M4x25
Machine Screw
3 pcs.
C
D
e
l
H.
Middle Shelf
1 pc.

Home Styles ConsumerAssistance: www.homestyles-furniture.com,
[email protected], 888-680-7460, 877-831-0319
For assembly also need the following : 88 5516-991
Part List
IMPORTANT NOTE
Carefully remove all the parts from the carton and put
them individually on a soft cloth to prevent scratches
or other damages occuring to the wood parts.
We have taken great care in the design of this
product and request that you carefully and strictly
follow our assembly instructions to ensure a
completed product as it was designed.
M.
Front Panel
1 pc.
88 5516 992
Barnside Bar
I.
Side Panel
1 pc.
Q.
Drawer
1 pc.
K.
Front Panel
1 pc.
L.
Front Panel
1 pc.
J.
Side Panel
1 pc.
O.
Front Rail
1 pc.
N.
Bottom
1 pc.
P.
Back Rail
1 pc. (Please refer to the last page of these
instructions for drawer assembly step.)

IMPORTANT
* Do not tighten up all the screws until each part is properly assembled.
* You should keep Hex Wrench in a safe place as you may need to tighten up the Head Cap Bolts in the future.
* Use a soft cloth between these parts and the floor.
*After assembly, item must be level to work properly. Use the included adjustable levelers to level.
B
STEP 1
Insert Cam Lock Screws into the pre-drilled holes of Top (A), Middle Panel
(B), Side Panel (I), (J), Middle Shelf (H) and Bottom (N). (see Figure 1) Figure 1
Assembly Instruction 2 / 5
N
Cam Lock Screw
J
I
H
Cam Lock Screw
A

Assembly Instruction 3 / 5
STEP 4
Attach Side Panels (I), (J) to unit from Step 3 with
Cam Locks and Head Cap Bolts. (see Figure 3)
Figure 2
STEP 2
Attach Front Panels (K) and (M) to
Front Panel (L).
Attach Front Rail (O) to panel unit.
L
P
STEP 3
Attach Middle Shelf (H) to panel
unit.
Attach Middle Panel (B) to Middle
Shelf (H) with Cam Locks.
(see Figure 2)
Attach Back Rail (P) to Middle
Panel (B) using Cam Lock.
Attach Bottom (N) to unit with
Cam Locks.
I
Head Cap Bolt
M
K
O
H
B
J
N
Figure 3
Cam Lock
Cam Lock
Figure 2

Assembly Instruction 4 / 5
STEP 5
Attach Foot Rests Supports (G) to unit
with Head Cap Bolts.
Attach Foot Rest (F) unit with Head
Cap Bolts.
Wood Screw (short)
G
Q
Head Cap Bolt
Adjustable Pin
Figure 4
STEP 6
Place Top (A) unit onto the unit
and attach with Cam Locks.
Attach Magnet to middle
panel with Wood Screws
(short). (see Figure 4)
Slide Drawer (Q) into position.
Insert Adjustable Pins into side
panels at the desired level.
Place Shelves (C) and (D) into
position.
Attach Door (E) to side panels by
sliding the door lift hinges
into the side panel lift hinges.
(see Figure 5)
Assemble Knob to Door
(E) with Machine Screw.
(see Figure 6)
To level the unit, adjust the
adjustable levelers on the bottom
of unit. (see Figure 7)
Note: Unit must be level to
work properly.
F
G
E
DC
C
A
Figure 5
Figure 6 Figure 7
Cam Lock
Magnet

STEP 2
Slide Q5 into the grooves in Q3
and Q4. Be sure to push Q5 all
the way forward so it meets
Q1. (see Figure 2)
Assembly Instruction 5 / 5
Drawer (Q)
Part List
Q2.
Back Part
1 pc.
Q3.
Side Part
1 pc.
Q4
Side Part
1 pc.
Q5.
Base Part
1 pc.
Q1.
Front Part
1 pc.
Q5
Q3
Q4
Q2
STEP 1
Attach Q1 to Q2 and Q4, using
a Phillips screwdriver and
long wood screws (4X), tighten
halfway.
Attach Q2 to Q3 and Q4 using
long wood screws (4X), tighten
halfway. (see Figure 1)
STEP 3
Insert short wood screws (6X)
into the pre-drilled holes in Q5
and tighten. (see Figure 3)
STEP 4
Assemble Pull Handle
with machine screws.
(see Figure 4)
Tighten all screws used in drawer assembly.
MAKE SURE ROLLER
IS ON THE BACK
Q2
Q3
Q4
Q1
Q1
Q5
Q1Q3
Q4
Figure 1
Figure 2
Figure 4Figure 3