Home Styles 5530-49 User manual

Hardware List
Part List
Tool(s) required for assembly: Phillips screwdriver, Level, Drill (8 volts or less), 3/8” Drill Bit
5530-49
Hall Tree Stand
IMPORTANT
Hex Wrench
1 pc.
Small Hex Wrench
1 pc.
Carefully remove all the parts from the carton and
place them individually on a soft cloth to prevent
scratches or other damage.
Carefully and strictly follow these assembly instructions
to ensure a completed product as designed.
Do not use power tools above 8 volts to assemble.
M6x28
Head Cap Bolt (long)
8 pcs. (+1 extra)
Spring Support
2 pcs.
M6x25
Head Cap Bolt
6 pcs. (+1 extra)
Dowel
2 pcs. (+1 extra)
M3x16
Wood Screw
34 pcs. (+1 extra)
M3x16
Wood Screw for Hook
8 pcs. (+1 extra)
M5x32
Wood Screw for Arm
4 pcs. (+1 extra)
Cam Lock Screw
24 pcs. (+1 extra)
Cam Lock
24 pcs. (+6 extra)
Hook
4 pcs.
B.
Side Panel
1 pc.
C.
Side Panel
1 pc.
S.
Side Panel
1 pc.
T.
Side Panel
1 pc.
D.
Front Panel
1 pc.
U.
Back Rail
1 pc.
V.
Upright
1 pc.
W.
Back Panel
2 pcs.
L.
Upright
1 pc.
M.
Back Panel
2 pcs.
X.
Back Panel
1 pc.
A.
Seat
1 pc.
P.
Arm
1 pc.
Q.
Arm
1 pc.
R.
Divider
1 pc.
N.
Front Rail
1 pc.
J.
Shelf
1 pc.
I.
Base
1 pc.
O.
Back Rail
2 pcs.
K.
Top
1 pc.
E.
Plinth
1 pc.
styles Customer Service: www.homestylesfurniture.com,home
[email protected], 888-680-7460

Assembly Instructions 2/11
IMPORTANT
Use a soft cloth between these parts and the floor.
Do not use power tools above 8 volts to assemble.
Do not tighten all the bolts until each part is properly assembled.
Keep Hex Wrench as the bolts may need to be tightened in the future.
Figure 1
Cam Lock Screw
STEP 1
Insert Cam Lock Screws into pre-drilled holes in Side Panels
(B), (C), (S), (T) and Top (K), then tighten.
(See Figure 1)
K
B
C
S
T

Assembly Instructions 3/11
Figure 3
Head Cap Bolt
Cam Lock
Figure 2
STEP 2
Attach Front Panel (D) to
Plinth (E) with Head Cap Bolts.
(See Figure 2)
Head Cap Bolt
STEP 3
Attach Front Panel (D) and Back Panel (X) to Side Panel (B)
with Cam Locks and Head Cap Bolt.
(See Figure 3)
B
D
X
D
E

Assembly Instructions 4/11
Figure 4
STEP 4
Attach Side Panel (C) to unit with
Cam Locks and Head Cap Bolt (short).
Cam Lock
Head Cap Bolt (short)
I
Wood Screw
STEP 5
Insert Base (I) into unit, then attach Base (I)
to unit with Wood Screws. (See Figure 4)
C

Assembly Instructions /511
STEP 6
Attach Spring Supports to Seat (A)
by inserting Wood Screws into
pre-drilled holes, then tighten.
(See Figure 5)
Figure 5
STEP 7
Attach Seat (A) to unit
with Head Cap Bolts (long),
tightening bolts only halfway.
A
A
Wood Screw
Spring Support
Head Cap Bolt (long)

Assembly Instructions /611
STEP 9
Attach Back Rail (U) to
Side Panel (S) with Cam Lock.
Slide Back Panels (M) and (W) into position.
U
W
M
Cam Lock
Figure 6
STEP 8
Attach Hooks to Back Rail (U) with Wood Screws for Hook.
(See Figure 6)
Wood Screw for Hook
Hook
S
U

Assembly Instructions /711
Cam Lock
STEP 10
Attach s (L) and (V) to unit.Upright
Attach Back Rails (O) to unit with Cam Locks.
L
V
O
O
STEP 11
Attach Shelf (J) and Front Rail (N) to unit with Cam Locks.
Slide Back Panels (M) and (W) into position.
Cam Lock
W
M
J
N

Assembly Instructions /811
STEP 12
Attach Side Panel (T)
to unit with Cam Locks.
STEP 13
Attach Arms (P) and (Q) to unit
with Dowels and Wood Screws for Arm.
Wood Screw for Arm
Dowel
Cam Lock
Q
P
T

Assembly Instructions /911
Head Cap Bolt (long)
STEP 14
Attach unit from Step 13 to unit from Step 7 with Head Cap Bolts (long).
Attach Divider (R) to unit.
Attach Top (K) to unit with Cam Locks.
Cam Lock
K
R

Assembly Instructions /10 11
STEP 15
Level unit by adjusting the
adjustable levelers on bottom of unit.
(See Figure 7)
Insert Wood Screws into
pre-drilled holes in unit, then tighten.
Note: Unit must be level
before tightening these screws.
STEP 16
Align Seat (A) so that Seat (A) is
spaced evenly between Arms (P) and (Q).
Without moving Seat (A) laterally, open Seat (A)
and tighten bolts used in Step 7.
(See Figure 8)
Figure 8
Wood Screw
A
P
Q
Figure 7