Home Styles Entertainment Credenza 88 5514 102 User manual

Part List
IMPORTANT NOTE
Carefully remove all the parts from the carton and put
them individually on a soft cloth to prevent scratches
or other damages occuring to the wood parts.
We have taken great care in the design of this
product and request that you carefully and strictly
follow our assembly instructions to ensure a
completed product as it was designed.
88 5514 101
Entertainment Credenza
Home Styles Consumer Assistance: www.homestyles-furniture.com,
[email protected], 888-680-7460, 877-831-0319
F.
Base
1 pc.
N.
Shelf
2 pcs.
A.
Top
1 pc.
I.
Front Rail
1 pc.
H.
Front Rail
1 pc.
J.
Back Panel
1 pc.
O.
Door
1 pc.
P.
Door
1 pc.
M.
Shelf
1 pc.
K.
Back Strip
1 pc.
L.
Back Panel
1 pc.
For assembly see instructions in carton 88 5514 102
Tools required for assembly : Phillips screwdriver, Drill, 3/8” Drill Bit, Level

Part List
IMPORTANT NOTE
Carefully remove all the parts from the carton and put
them individually on a soft cloth to prevent scratches
or other damages occuring to the wood parts.
We have taken great care in the design of this
product and request that you carefully and strictly
follow our assembly instructions to ensure a
completed product as it was designed.
88 5514 102
Entertainment Credenza
Home Styles Consumer Assistance: www.homestyles-furniture.com,
[email protected], 888-680-7460, 877-831-0319
B.
Side Panel
.1 pc
C.
Side Panel
1 pc.
D.
Middle Panel
.1 pc
E.
Middle Panel
.1 pc
Tools required for assembly : Phillips screwdriver, Drill, 3/8” Drill Bit, Level
Also need the Parts in carton 88 5514 101
Hardware List
Adjustable Pin
12 pcs.(+1 extra)
Pull Handle
2 pcs.
M4x19
Machine Screw
4pcs.
Bolt
for Back Panel
6 pcs.(+1 extra)
M3x16
Wood Screw
for Magnet
4 pcs.(+1 extra)
Magnet
2 pcs.
G.
Leg Support
1 pc.
Q.
Drawer
1 pc.
R.
Drawer
2 pcs.
(Please refer to the last page of these instructions for drawer assembly steps.)

STEP 1
STEP 2
Assembly Instructions 2/6
Attach Middle Panels (D) and (E)
to Base (F), then flip the Locks. (See Figures 1 and 2)
Attach Leg Support (G) to unit and tighten.
IMPORTANT
* Do not tighten up all the screws until each part is properly assembled.
* After assembly, item must be level to work properly. Use the included adjustable levelers to level.
* Use a soft cloth between these parts and the floor.
F
D
E
Figure 1
Figure 2
G
H
I
Magnet
Figure 3
Attach Magnets to Front Rail (I) with
Wood Screws for Magnet. (See Figure 3)
Attach Front Rails (H) and (I) to unit.
Attach Side Panels (B) and (C) to unit, then flip the Locks.
C
B

STEP 3
STEP 4
Assembly Instructions 3/6
Turn unit to its’ upright position.
Slide Back Panel (L), Back Strip (K)
and Back Panel (J) into position.
Insert Bolts for Back Panel into the
pre-drilled holes of Back Panels (J)
and (L). (See Figure 4)
J
Bolt
for Back Panel
Figure 4
A
K
L
Figure 5
Figure 6
J
Figure 7
Attach Top (A) to the unit,
then flip the Locks.
Insert Adjustable Pins into side panels and middle panels at the desired level.
(See Figure 5)
Place Shelves (M) and (N) into position.
Attach Doors (O) and (P) by sliding the door lift hinges into the side panels
lift hinges. (See Figure 6)
Assemble Pull Handles to Doors (O) and (P) with Machine Screws. (See Figure 7)
Slide Drawers (Q) and (R) into position.
To level the unit, adjust the adjustable levelers on the bottom of legs. (See Figure 8)
Note : Unit must be level to work properly.
Figure 8
QR
R
MN
N
O
P
Adjustable Pin

Assembly Instructions 4/6
Wood Screw
Wall Screw
Anchor
1 pc.(+1 extra)
Bracket
2 pcs.(+1 extra)
Tipover Restraint
1 pc.(+1 extra)
Hardware List
Attention!
To help reduce the risk of the unit tipping over, the Tipover Restraint be installed followingmust
these instructions exactly!
M3.5x40
Wall Screw
1 pc.(+1 extra)
tie end
loop end
Place unit at desired location.
Drill a hole in wall3/8”
at the appropriate location.
Insert Anchor into the wall hole
and attach Bracket with Wall Screw.
Attach Bracket at pre-drilled hole at top
of unit with Wood Screw.
Use Tipover Restraint to secure Bracket
on unit to Bracket on wall.
(See Figure X)
Put tie end of Tipover Restraint into loop end
of Tipover Restraint and pull until tight. Figure X
Bracket
on wall
Anchor in wall
3/8” wall hole
Bracket at
top of unit
Tipover
Restraint
Wood Screw
Wall Screw
Anchor
1 pc.(+1 extra)
Bracket
2 pcs.(+1 extra)
Tipover Restraint
1 pc.(+1 extra)
Hardware List
Attention!
To help reduce the risk of the unit tipping over, the Tipover Restraint be installed followingmust
these instructions exactly!
M3.5x40
Wall Screw
1 pc.(+1 extra)
tie end
loop end
Place unit at desired location.
Drill a hole in wall3/8”
at the appropriate location.
Insert Anchor into the wall hole
and attach Bracket with Wall Screw.
Attach Bracket at pre-drilled hole at top
of unit with Wood Screw.
Use Tipover Restraint to secure Bracket
on unit to Bracket on wall.
(See Figure X)
Put tie end of Tipover Restraint into loop end
of Tipover Restraint and pull until tight. Figure X
Bracket
on wall
Anchor in wall
3/8” wall hole
Bracket at
top of unit
Tipover
Restraint
M3.5x16
Wood Screw
1 pc.(+1 extra)
Drill 3/8” hole in wallDrill 3/8” hole in wall
Top of unit

Assembly Instructions 5/6
Q2
Q2
Q3
Q3
Q1
Q4
Q4 Q5
Drawer (Q)
Part List
Q1.
Drawer Front
1 pc.
Q5.
Drawer Bottom
1 pc.
Q2.
Drawer Back
1 pc.
Q3.
Drawer Side
1 pc.
Q4.
Drawer Side
1 pc.
Attach Q2 to Q3 and Q4, then flip the Locks.
(See Figures A and B)
Attach Q1 to unit, then flip the Locks.
Slide Q5 into the grooves in Q3 and Q4.
Be sure to push Q5 all the way forward so
it meets Q2.
STEP 1
STEP 2
STEP 3
Figure A Figure B

Assembly Instructions 6/6
R2
R2
Q3
Q3
R1
Q4
Q4 R5
Drawer (R)
Part List
R1.
Drawer Front
2 pcs.
R5.
Drawer Bottom
2 pcs.
R2.
Drawer Back
2 pcs.
Q3.
Drawer Side
2 pcs.
Q4.
Drawer Side
2 pcs.
Attach R2 to Q3 and Q4, then flip the Locks.
(See Figures A and B)
Attach R1 to unit, then flip the Locks.
Slide R5 into the grooves in Q3 and Q4.
Be sure to push R5 all the way forward so
it meets R2.
STEP 1
STEP 2
STEP 3
Figure A Figure B