Home Styles 6730-10 User manual

Part List
6730-10
Chair
B.
Side
1 pc.
G.
Back Cushion
1 pc.
E.
Non-slip Pad
1 pc.
C.
Side
1 pc.
D.
Rail
1 pc.
F.
Seat Cushion
1 pc.
Hardware List
Small
Hex Wrench
1 pc.
Hex Wrench
1 pc.
Spring Washer
10 pcs. (+1 extra)
M6x35
Head Cap Bolt
6 pcs. (+1 extra)
M6x20
Head Cap Bolt (short)
4 pcs. (+1 extra)
Flat Washer
10 pcs. (+1 extra)
Cap
10 pcs. (+1 extra)
styles Customer Service: www.homestylesfurniture.com,home
[email protected], 888-680-7460
A.
Seat
1 pc.
aaaaaa
aaaaaa
aaaaaa
aaaaaa
IMPORTANT
Carefully remove all the parts from the carton and place them
individually on a soft cloth to prevent scratches or other damage.
Carefully and strictly follow these assembly instructions
to ensure a completed product as designed.
This product is made of aluminum. Do not use power tools
above 8 volts to assemble and only tighten bolts until snug.
Over tightening can damage the aluminum.

Assembly Instructions 2/5
IMPORTANT
Use a soft cloth between these parts and the floor.
Do not use power tools above 8 volts to assemble.
Do not tighten all the bolts until each part is properly assembled.
Keep Hex Wrench as the bolts may need to be tightened in the future.
Figure 1
STEP 1
Attach (D) to Side (B) with Head Cap Bolts (short), Spring Washers and Flat Washers,Rail
tightening bolts only halfway. (See Figure 1)
Attach Seat (A) to unit with Head Cap Bolts, Spring Washers
and Flat Washers, tightening bolts only halfway.
Head Cap Bolt
Spring Washer
Flat Washer
Flat Washer
Spring Washer
Head Cap Bolt (short)
A
B
D

STEP 2
Attach Side (C) to unit with Head Cap Bolts, Head Cap Bolts (short), Spring Washers
and Flat Washers, tightening bolts only halfway.
Tighten all bolts used in Steps 1 and 2.
Cover all Head Cap Bolts with Caps. (See Figure 2)
Assembly Instructions /35
C
Flat Washer
Spring Washer
Head Cap Bolt
Flat Washer
Spring Washer
Head Cap Bolt (short)
Cap
Figure 2

Assembly Instructions /45
STEP 3
Turn unit to its upright position.
Place Non-slip Pad (E) into position.
aaaaaaaaa
aaaaaaaaa
aaaaaaaaa
aaaaaaaaa
aaaaaaaaa
aaaaa
aaaaa
aaaaa
aaaaa
E

Assembly Instructions /55
STEP 4
Place Seat Cushion (F) into position.
Place Back Cushion (G) into position.
F
G
Cushion Care Instructions
Keep cushions free of natural debris.
Tip and angle cushions after use.
Store cushions inside when not in use.
Allow a minimum of 24 hours for wet cushions to air dry.
Never use a hairdryer on cushions.
Never put cushions in a clothes dryer.
Cushion covers are hand wash and air dry only.

Part List
6730-90
Ottoman
B.
Side
2 pcs.
Hardware List
Small
Hex Wrench
1 pc.
Hex Wrench
1 pc.
Spring Washer
10 pcs. (+1 extra)
M6x35
Head Cap Bolt
10 pcs. (+1 extra)
Flat Washer
10 pcs. (+1 extra)
Cap
10 pcs. (+1 extra)
styles Customer Service: www.homestylesfurniture.com,home
[email protected], 888-680-7460
A.
Seat
1 pc.
C.
Cushion
1 pc.
IMPORTANT
Carefully remove all the parts from the carton and place them
individually on a soft cloth to prevent scratches or other damage.
Carefully and strictly follow these assembly instructions
to ensure a completed product as designed.
This product is made of aluminum. Do not use power tools
above 8 volts to assemble and only tighten bolts until snug.
Over tightening can damage the aluminum.

Assembly Instructions 2/3
IMPORTANT
Use a soft cloth between these parts and the floor.
Do not use power tools above 8 volts to assemble.
Do not tighten all the bolts until each part is properly assembled.
Keep Hex Wrench as the bolts may need to be tightened in the future.
Figure 1
STEP 1
Attach Side (B) to Seat (A) with Head Cap Bolts, Spring Washers and Flat Washers,
tightening bolts only halfway.
(See Figure 1)
Flat Washer
Spring Washer
Head Cap Bolt
B
A
Flat Washer
Spring Washer
Head Cap Bolt
STEP 2
Attach Side (B) to unit with Head Cap Bolts,
Spring Washers and Flat Washers,
tightening bolts only halfway.
Tighten all bolts used in Steps 1 and 2.
Cover all Head Cap Bolts with Caps.
(See Figure 2)
Cap
Figure 2
B

Assembly Instructions /33
STEP 3
Turn Cushion (C) upside down.
Use velcro on Cushion (C) to attach to unit. (See Figure 3)
STEP 4
Turn over unit to it’s upright position.
C
Velcro
Velcro
Figure 3

NEVER
use glass cleaners on
finished furniture. Ammonia
chemically attacks the finish.
allow liquids to remain on furniture.
Absorption causes parts to warp
and split and finishes to delaminate.
NEVER
CARE INSTRUCTIONS
Do not use rubber
based placemats.
PREVENT
DISCOLORING
Do not use commercial
waxes and polishes.
PREVENT
YELLOWING
Do not place hot
objects on surface.
PREVENT
FINISH DAMAGE
Do not write
directly on surface.
PREVENT
MARKING
Do not use power tools
above 8 volts to assemble.
PREVENT
CRACKING
Do not place
in direct sunlight.
PREVENT
FADING
with a soft cloth moistened
in lukewarm soap and water.
Buff with a dry clean cloth.
CLEAN
homestyles will provide replacements free of charge for missing or damaged parts within 2 years of purchase.
Digital images of the defective parts may be required. If the product was not purchased from an authorized retailer,
homestyles is under no obligation to provide replacement parts. Parts are not available for fully assembled items nor
are parts available for sale. Replacements for missing or damaged parts may be requested via contact info below.
styles Customer Service: www.homestylesfurniture.com,home
[email protected], 888-680-7460