Home Styles Orleans 88 5061 66 User manual

IMPORTANT NOTE
Carefully remove all the parts from the carton and put
them individually on a soft cloth to prevent scratches
or other damage occurring to the parts.
We have taken great care in the design of this
product and request that you carefully and strictly
follow our assembly instructions to ensure a
completed product as it was designed.
Part List
Home Styles ConsumerAssistance: www.homestyles-furniture.com,
[email protected], 888-680-7460, 877-831-0319
Hardware List
88 5061 66
Orleans
Wine Rack
Tools required for assembly : Phillips screwdriver Tools recommended for assembly : Level
Hex Wrench
1 Pc.
Small Hex Wrench
1 Pc.
Head Cap Bolt (long)
4 Pcs.(+1 extra) Head Cap Bolt (short) 2 Pcs.(+1 extra)
M6x38 M6x16 M6x16 M3x32
Tapered Head Cap Bolt
20 Pcs.(+1 extra) Spring Washer
6 Pcs.(+1 extra) Flat Washer 6 Pcs.(+1 extra) Wood Screw 8 Pcs.(+1 extra)
A.
Top Unit
1 Pc.
B.
Side Frame
2 Pcs.
C.
Shelf
2 Pcs.
D.
Shelf
1 Pc.
E.
Support
1 Pc.
F.
Wine Rack
2 Pcs.
G.
Wine Glass Rack (long)
2 Pcs.
H.
Wine Glass Rack (short)
2 Pcs.

Assembly Instructions 2
IMPORTANT
* Please keep Hex Wrench in a safe place as you may need to tighten up the Head Cap Bolts in the future.
* Do not tighten up all the bolts until each part is properly assembled.
* Use a soft cloth between these parts and the floor.
*After assembly item must be level to work properly. Use the included adjustable levelers to level.
STEP 1
Attach Wine Glass Racks (short) (H)
to Shelves (C) with Tapered Head Cap Bolts.
(see Figure 1)
STEP 2
Attach Side Frames (B) to Support (E) with Flat Washers,
Spring Washers and Head Cap Bolts (short). (see Figure 2)
Attach unit to Top Unit (A) with Tapered Head Cap Bolts. (see Figure 3)
Tighten all Bolts only half way with Hex Wrench.
A
H
H
C
C
B
B
E
Tapered Head Cap Bolt
Tapered Head Cap bolt
/4
Figure 2
Head Cap Bolt (short)
Spring Washer
Flat Washer
Figure 3
Figure 1

Assembly Instructions 3
STEP 3
Attach Shelf (D) to the unit with
Wood Screws.
STEP 4
Slide Wine Racks (F) into position by putting their bottom tabs into the
pre-drilled holes in Shelf (D). (see Figure 4)
Attach Wine Racks (F) to the unit with Flat Washers, Spring Washers and Head Cap Bolts (long).
Tighten all Bolts with Hex Wrench.
/4
D
D
F
F
Head Cap Bolt (long)
Spring Washer
Flat Washer
Wood Screw
Figure 4

Assembly Instructions 4
STEP 6
Turn the unit to its’ upright position.
To level the unit, adjust the adjustable
levelers on the bottom of unit.
(see Figure 5)
Note: Unit must be level to
work properly.
Figure 5
CC
GG
STEP 5
Turn the unit to its’ upright position.
Attach Wine Glass Racks (long) (G)
to the unit with Tapered Head Cap
Bolts.
Attach Shelves (C) to the unit with
Wood Screws.
Wood Screw
Tapered Head Cap Bolt
/4