Home Styles 88 5660 30 User manual

Hardware List
Home Styles Consumer Assistance: www.homestyles-furniture.com,
[email protected], 888-680-7460, 877-831-0319
Extension Table
IMPORTANT NOTE
Carefully remove all the parts from the carton and put
them individually on a soft cloth to prevent scratches
or other damages occuring to the parts.
We have taken great care in the design of this
product and request that you carefully and strictly
follow our assembly instructions to ensure a
completed product as it was designed.
Part List
88 5660 30
A.
Top
1pc
B.
Top
1pc
H.
Support
1pc
M.
Pipe
1pc
Cover
1 pc.
Tools required for assembly : Phillips screwdriver
Head Cap Bolt
(Long)
4 pcs.(+1 extra)
L.
Rail
1pc
Hex Wrench
4mm
1pc
N.
Stretcher
1pc
Assembly Screw
4 pcs.(+1 extra)
Small Hex Wrench
4mm
1 pc.
Dowel
4 pcs.(+1 extra)
Cover
2 pcs.
Bali Hai
Head Cap Bolt
(Middle)
8 pcs.(+1 extra)
Wood Screw
(Long)
4 pcs.(+1 extra)
Head Cap Bolt
(Short)
8 pcs.(+1 extra)
C.
Top
1pc
D.
Block
2 pcs
G.
Support
1pc
K.
Support
2 pcs
O.
Stretcher
1pc
I.
Leg
2 pcs
J.
Leg
2 pcs
E.
Leg Support
1pc
F.
Leg Support
1pc
Wood Screw
(Short)
2 pcs.(+1 extra)

Assembly Instructions 2/4
* Do not tighten up all the screws until each part is properly assembled.
* You should keep Hex Wrench in a safe place as you may need to tighten up the Head Cap Bolts in the future.
* Use a soft cloth between these parts and the floor.
STEP 1
Attach Stretcher (N) to Stretcher (O),
with Wood Screws (Short).
STEP 2
Attach Leg Supports (E) and (F) to Legs (I)
and (J) with Assembly Screws.
Attach Rail (L) to Leg Supports (E) and (F).
Attach unit from Step 1 to Legs (I) and (J) with
Head Cap Bolts (Middle).
IMPORTANT
I
Wood Screw (Short)
Head Cap Bolt (Middle)
O
J
F
E
L
J
I
Head Cap Bolt (Middle)
STEP 3
Attach Blocks (D) to Pipe (M).
Attach Pipe into the pre-drilled holes of
Supports (G) and (H).
Attach Supports (K) to Supports (G) and (H)
with Head Cap Bolts (Middle).
Assembly Screw
KH
D
M
K
G
N

Assembly Instructions 3/4
STEP 4
Attach Top (B) to unit from Step 3 with
Wood Screws (Long) into the pre-drilled holes.
Wood Screw (Long)
B
STEP 5
Place the unit from Step 2 in an upright position.
Attach unit from Step 4 to unit from Step 2
with Head Cap Bolts (Long) and Head Cap
Bolts (Short).
STEP 6
Attach Top (A) and (C) to unit by sliding into the groove in Supports (K).
Insert the Dowels into the holes of the rail in bottom side of Tops (A) and (C). (See figure 1)
C
Figure 1 (bottom view)
A
Dowel
Head Cap Bolt (Short)
Head Cap Bolt (Long)

Assembly Instructions 4/4
STEP 7
Put Covers into the holes of the top
when not using an umbrella.
Covers
Figure 2 (bottom view)
Close
Open
Lock
To Shorten the Table
Open the locks under the top. (See Figure 2)
Pull the half tops slightly apart, fold up the center top and rotate it
so that it fits into the table base.
Push the half tops together.
Close the locks under the top. (See Figure 2)