Home Styles 88 5003 991 User manual

IMPORTANT NOTE
Carefully remove all the parts from the carton and put
them individually on a soft cloth to prevent scratches
or other damage occurring to the parts.
We have taken great care in the design of this
product and request that you carefully and strictly
follow our assembly instructions to ensure a
completed product as it was designed.
Part List
Home Styles ConsumerAssistance: www.homestyles-furniture.com,
[email protected], 888-680-7460, 877-831-0319
88 5003 991
Bar
For assembly see instructions in carton 88 5003 992
E.
Glass Holder
1 Pc.
A.
Top
1 Pc.
I.
Front Panel
1 Pc.
H.
Front Panel
2 Pcs.
N.
Door
1 Pc.
B.
Sub Top
1 Pc.
C.
Front Panel
1 Pc.

IMPORTANT NOTE
Carefully remove all the parts from the carton and put
them individually on a soft cloth to prevent scratches
or other damage occurring to the parts.
We have taken great care in the design of this
product and request that you carefully and strictly
follow our assembly instructions to ensure a
completed product as it was designed.
Part List
Home Styles ConsumerAssistance: www.homestyles-furniture.com,
[email protected], 888-680-7460, 877-831-0319
Hardware List
88 5003 992
Bar
Tools required for assembly : Phillips screwdriver Tools recommended for assembly : Level
Cam Lock
39 Pcs. (+6 extra)
Hex Wrench
1 Pc.
Small Hex Wrench
1 Pc.
Adjustable Pin
12 Pcs. (+1 extra)
Magnet
1 Pc.
M3x12
Wood Screw
for Magnet
2 Pcs. (+1 extra)
M3x15
Tapered Wood Screw
12 Pcs. (+1 extra)
M6x10
Head Cap Bolt
3 Pcs. (+1 extra)
Head Cap Bolt
11 Pcs. (+1 extra) Flat Washer
11 Pcs. (+1 extra)
M6x25 Pull Handle
2 Pcs.
Machine Screw
2 Pcs.
M4x25
Cam Lock Screw
39 Pcs. (+2 extra)
D.
Side Panel
2 Pcs.
J.
Side Panel
1 Pc.
K.
Side Panel
1 Pc.
L.
Middle Panel
1 Pc.
G.
Front Rail
1 Pc.
F.
Front Rail
1 Pc.
M.
Base
1 Pc.
O.
Shelf
3 Pcs.
Q.
Foot Rest
1 Pc.
P.
Foot Rest Support
3 Pcs.
R.
Drawer
1 Pc.
(Please refer to the last page(s) of
instructions for steps to complete drawer assembly)
M3x25
Long Wood Screw
8 Pcs. (+1 extra)

Assembly Instructions
IMPORTANT
* Please keep Hex Wrench in a safe place as you may need to tighten up the Head Cap Bolts in the future.
* Do not tighten up all the bolts until each part is properly assembled.
* Use a soft cloth between these parts and the floor.
*After assembly item must be level to work properly. Use the included adjustable levelers to level.
STEP 1
Insert Cam Lock Screws into
the pre-drilled holes in Tops (A) and Sub Top (B), Front Panels (H), Side Panel (K),
Middle Panel (L), and Base (M). (See Figure 1)
STEP 2
Place Top (A)
upside down on a soft cloth.
Attach Side Panels (D) and
Front Panel (C) to Top (A) with Cam Locks.
Attach Sub Top (B) to top unit with Head Cap Bolts and Flat Washers.
B
H
H
A
KL
B
C
A
D
D
M
Figure 1
Cam Lock Screw
Head Cap Bolt
Flat Washer
2/6

Assembly Instructions
STEP 3
Attach Front Panels (H)
to Front Panel (I) with Cam Locks.
STEP 4
Attach Magnet to Front Rail (G)
with Wood Screws for Magnet.
(See Figure 2)
Attach Side Panel (J) and (K) to unit from Step 3, then attach unit
to Base (M) with Cam Locks.
Attach Front Rails (F) and (G) and Middle Panel (L) to unit with Cam Locks.
M
G
F
K
L
I
H
H
J
Magnet
Wood Screw
for Magnet
3/6
Figure 2

Assembly Instructions
O
NO
O
R
E
Adjustable Pin
STEP 5
Insert Adjustable Pins into side panels and middle panel at the desired level.
Slide Shelves (O) into position.
Attach top unit to body unit with Cam Locks, then attach Glass Holder (E) to unit with Head Cap
Bolts and Flat Washers.
Attach Pull Handle to Door (N) with Machine Screw. (See Figure 3)
Attach Door (N) to unit by sliding the door lift hinges into the side panel lift hinges. (See Figure 4)
Slide Drawer (R) into place.
4/6
Figure 4
Figure 3
Flat Washer
Head Cap Bolt

Assembly Instructions
STEP 6
Slide Foot Rest (Q) into the Foot Rest Supports (P).
Attach Foot Rest Supports (P) to unit at the pre-drilled holes with
Tapered Wood Screws.
Attach Foot Rest (Q) to Foot Rest Supports (P) with Head Cap
Bolts (short), leaving the same amount of Foot Rest (Q) protruding
on the outside of the outer Foot Rest Supports (P). (See Figure 5)
STEP 7
To level the unit, adjust the adjustable levelers on the bottom
of the unit. (See Figure 6)
Note: Unit must be level to work properly. Figure 6
Figure 5
Q
P
P
P
5/6
Tapered
Wood Screw
Same amount of
Foot Rest (Q) on
each side
Head Cap Bolt
(short)

Assembly Instructions
Part List
Drawer R
R1.
Front Part
1 Pc.
R2.
Back Part
1 Pc.
R3.
Side Part
1 Pc.
R4.
Side Part
1 Pc.
R5.
Base Part
1 Pc.
Figure 3
6/6
STEP 3
Attach Drawer Handles with
Machine Screws.
(See Figure 3)
R1
R2
R5
R3
R4
STEP 1
Attach Side Part R3 to Front Part (R1)
and Back Part (R2) using a
Phillips screwdriver and long wood
screws (4X), tighten halfway.
(See Figure 1)
STEP 2
Insert Base Part (R5) into the groove.
Attach Side Part (R4) to Front Part (R1) and
Back Part (R2) using a Phillips screwdriver
and long wood screws (4X). (See Figure 2)
Tighten all wood screws used in drawer assembly.
Figure 1
Figure 2
MAKE SURE ROLLER
IS ON THE BACK