Home Styles 88 5077 691 User manual

Part List
IMPORTANT NOTE
Carefully remove all the parts from the carton and put
them individually on a soft cloth to prevent scratches
or other damages occurring to the parts.
We have taken great care in the design of this
product and request that you carefully and strictly
follow our assembly instructions to ensure
a completed product as it was designed.
Home Styles Consumer Assistance Line 888-680-7460 and 877-831-0319
[email protected]
88 5077 691
C.
Side Panel
1 pc.
D.
Side Panel
1 pc.
B.
Front Rail
1 pc.
J.
Back Panel
2 pcs.
Pantry
A.
Top
1 pc.
H.
Back Stretcher
2 pcs.
E.
Shelf
2 pcs.
I.
Back Piece
1 pc.
G.
Door
1 pc.
F.
Door
1 pc.
For assembly see instructions in carton 88 5077 692

Part List
IMPORTANT NOTE
Carefully remove all the parts from the carton and put
them individually on a soft cloth to prevent scratches
or other damages occurring to the parts.
We have taken great care in the design of this
product and request that you carefully and strictly
follow our assembly instructions to ensure
a completed product as it was designed.
Home Styles Consumer Assistance Line 888-680-7460 and 877-831-0319
[email protected]
88 5077 692
(Knock-Down Construction, please refer
to the last page of these instructions for
drawer assembly steps)
Tools required for assembly : Phillips screwdriver, Drill, 3/8” Drill Bit, Level
Pantry
Hardware List
R.
Drawer
1 pc.
K.
Top
1 pc.
N.
Side Panel
1 pc.
M.
Side Panel
1 pc.
O.
Base
1 pc.
P.
Back Piece
1 pc.
Q.
Back Panel
2 pcs.
Hex Wrench
1 pc.
Small
Hex Wrench
1 pc.
M4x20
Machine Screw
1 pc.
Cam Lock Screw
30 pcs.(+1 extra)
Cam Lock
30 pcs.(+4 extra)
M3.5x25
Wood Screw (long)
8 pcs. (+1 extra)
Adjustable Pin
16 pcs. (+1 extra)
M3.5x16
Wood Screw (short)
20 pcs. (+1 extra)
Knob
1 pc.
L.
Front Rail
1 pc.
F.
Door
1 pc.
G.
Door
1 pc.
H.
Back Stretcher
2 pcs.
E.
Shelf
2 pcs.
Also need the following from carton 88 5077 691

Assembly Instructions 2/8
K
Figure 1
STEP 1
Put Cam Lock Screws into the pre-drilled holes of Top (A), (K)
Side Panels (C), (D), (M), (N) and Base (O) and tighten.
(see Figure 1)
Cam Lock Screw
A
D
C
Cam Lock Screw Cam Lock Screw
M
N
O
Cam Lock Screw
IMPORTANT
* Do not tighten up all the screws until each part is properly assembled.
* You should keep Hex Wrench in a safe place as you may need to tighten up the Cam Locks in the future.
* Use a soft cloth between these parts and the floor.
* After assembly, item must be level to work properly. Use the included adjustable levelers to level.

Assembly Instructions 3/8
Cam Lock
Q
STEP 3
Attach unit to Base (O) with Cam Locks.
Attach Top (K) to unit with Cam Locks.
Figure 2
P
Q
M
L
H
H
K
O
N
Cam Lock
STEP 2
Attach Back Stretcher (H)
to Side Panel (M) with Cam Lock.
(see Figure 2)
Attach Back Piece (P) to Back
Stretcher (H).
Slide Back Panels (Q) into position.
Attach Back Stretcher (H) and Front Rail (L)
to unit with Cam Locks.
Attach Side Panel (N) to unit with
Cam Locks.

Assembly Instructions 4/8
STEP 5
Attach Top (A) to unit from Step 4 with Cam Locks.
B
C
HJ
I
J
H
A
D
Cam Lock
Cam Lock
STEP 4
Attach Back Stretcher (H)
to Side Panel (C) with Cam
Lock.
Attach Back Piece (I) to Back
Stretcher (H).
Slide Back Panels (J) into
position.
Attach Back Stretcher (H) and
Front Rail (B) to unit with Cam
Locks.
Attach Side Panel (D) to unit with
Cam Locks.

Assembly Instructions 5/8
STEP 6
Attach unit from Step 5 to unit from Step 3
with Cam Locks.
STEP 7
Attach Doors (F) and (G) to unit by sliding
the door lift hinges into the side panel lift hinges.
(see Figure 3)
Figure 3
G
F
G
F
Cam Lock

Assembly Instructions 6/8
Note: Unit must be level before tightening these screws.
STEP 8
Insert the Adjustable Pins into the
side panels at the desired level.
Place Shelves (E) into position.
Slide Drawer (R) into position.
STEP 9
To level the unit, adjust the adjustable
levelers on the bottom of unit. (see Figure 4)
Insert Wood Screws (short) from the back
of the unit and tighten. (see Figure 5)
Figure 5
Figure 4
E
E
E
R
E
Wood Screw (short)
Adjustable Pin

Wood Screw
Wall Screw
M3.5x13
Wood Screw
1 pc.(+1 extra)
Anchor
1 pc.(+1 extra)
Bracket
2 pcs.(+1 extra)
Tipover Restraint
1 pc.(+1 extra)
Hardware List
Drill 3/8” hole in wall
Top of unit
Attention!
To help reduce the risk of the unit tipping over, the Tipover Restraint be installed followingmust
these instructions exactly!
M3.5x40
Wall Screw
1 pc.(+1 extra)
tie end
loop end
Place unit at desired location.
Drill a hole in wall3/8”
at the appropriate location.
Insert Anchor into the wall hole
and attach Bracket with Wall Screw.
Attach Bracket at pre-drilled hole at top
of unit with Wood Screw.
Use Tipover Restraint to secure Bracket
on unit to Bracket on wall.
(see Figure X)
Put tie end of Tipover Restraint into loop end
of Tipover Restraint and pull until tight.
Figure X
Assembly Instructions 7/8
Bracket
on wall
Anchor in wall
3/8” wall hole
Bracket at
top of unit
Tipover
Restraint

(Figure 3)
Insert Wood Screws (short)
into the pre-drilled holes in R5,
tighten screws. (see Figure 3)
Attach Knob with
machine screw.
(see Figure 4)
Slide R5 into the grooves in R3
and R4. Be sure to push R5 all
the way forward to it meets R1.
(see Figure 2)
STEP 4
Tighten all screws used in drawer assembly.
(Figure 1)
(Figure 2)
MAKE SURE ROLLER
IS ON THE BACK
R5
Drawer R
Part List
R1.
Drawer Front
1 pc.
R5.
Drawer Bottom
1 pc.
R2.
Drawer Back
1 pc.
R3.
Drawer Side
1 pc.
R4.
Drawer Side
1 pc.
(Figure 4)
STEP 1
STEP 2
STEP 3
Attach R1 to R3 and R4, using
Wood Screws (long), tighten
halfway.
Attach R2 to R3 and R4 using
Wood Screws (long), tighten
halfway. (see Figure 1)
R1
R2 R4
R3
Assembly Instructions 8/8
R1
R3
R4
R2
R1
R4
R2
R5
R3