Home Styles 5412 15 User manual

Executive Desk
Hardware List
Part List
Tool(s) required for assembly: Phillips screwdriver, Level
5412 15-
IMPORTANT
Carefully remove all the parts from the carton and
place them individually on a soft cloth to prevent
scratches or other damage.
Carefully and strictly follow these assembly instructions
to ensure a completed product as designed.
Do not use power tools above 8 volts to assemble.
Small Hex Wrench
1 pc.
Hex Wrench
1 pc.
Spring Washer
17 pcs. (+1 extra)
M6x32
Head Cap Bolt
17 pcs. (+1 extra)
Cam Lock
8 pcs. (+1 extra)
Cam Lock Screw
8 pcs. (+2 extra)
M3x15
Wood Screw
6 pcs. (+1 extra)
D.
Middle Panel
1 pc.
E.
Middle Panel
1 pc.
J.
Front Rail
2 pcs.
G.
Back Rail
1 pc.
H.
Front Rail
1 pc.
I.
Front Rail
1 pc.
F.
Back Panel
1 pc.
Refer to later page(s) of these
instructions for drawer assembly.
K
Drawer
2 pcs.
M.
Keyboard
1 pc.
L
Keyboard Front
1 pc.
A.
Top
1 pc.
B.
Side Frame
1 pc.
C.
Side Frame
1 pc.
M4x38
Wood Screw (long)
2 pcs. (+1 extra)
Flat Washer
17 pcs. (+1 extra)
M4x19
Machine Screw
8 pcs.
M4x25
Machine Screw (long)
4 pcs.
Knob
6 pcs.
styles Customer Service: www.homestylesfurniture.com,home
[email protected], 888-680-7460

Assembly Instructions 2/6
IMPORTANT
Use a soft cloth between these parts and the floor.
Do not use power tools above 8 volts to assemble.
Do not tighten all the bolts until each part is properly assembled.
The unit must be level to work properly. Use the included adjustable levelers to level.
Keep Hex Wrench as the bolts may need to be tightened in the future.
Cam Lock Screw
STEP 1
Insert Cam Lock Screws into pre-drilled
holes of Side Frames (B), (C) and
Middle Panels (D), (E), then tighten.
(See Figure 1)
Cam Lock Screw
STEP 2
Attach Middle Panels (D) and (E) to Front Rail (I) with Cam Locks.
(See Figure 2)
Attach unit to Back Panel (F) with Flat Washers, Spring Washers and
Head Cap Bolts. (See Figure 3)
Figure 2
Figure 3
F
Cam Lock
Head Cap Bolt
Spring Washer
Flat Washer
Figure 1
C
B
DE
E
D
I

Assembly Instructions 3/6
STEP 4
Attach Front Rails (J) to unit with Cam Locks.
Attach Side Frame (C) to unit with Cam Locks, Flat Washers, Spring Washers and Head Cap Bolts.
Cam Lock
Flat Washer
Spring Washer
Head Cap Bolt
STEP 3
Place Top (A) upside down on a soft cloth.
Attach unit and Front Rail (H) to
Top (A) with Flat Washers, Spring Washers
and Head Cap Bolts.
Head Cap Bolt
Spring Washer
Flat Washer
A
C
J
J
H

Figure 5 Figure 6
Figure 4
Knob
Assembly Instructions 4/6
Machine Screw (long)
STEP 5
Attach Back Rail (G) to
unit with Wood Screw (long). (See Figure 4)
Attach Side Frame (B) to unit with Flat Washers,
Spring Washers, Head Cap Bolts, Cam Locks and Wood Screw (long).
Flat Washer
Spring Washer
Head Cap Bolt
Wood Screw (long)
Cam Lock
STEP 6
Attach Keyboard Front (L) to
Keyboard (M) with Wood Screws.
(See Figure 5)
Attach Knobs to Keyboard Front (L)
with Machine Screws (long).
(See Figure 6)
M
Wood Screw
G
B
L

Assembly Instructions 5/6
STEP 7
Attach Drawer Sides (K3) and (K4) to
Drawer Back (K2), then flip Locks.
(See Figures 7 and 8)
Figure 7 Figure 8
STEP 9
Attach Knobs with Machine Screws.
K1.
Drawer Front
2 pcs.
K2.
Drawer Back
2 pcs.
K3.
Drawer Side
2 pcs.
K4.
Drawer Side
2 pcs.
K5.
Drawer Bottom
2 pcs.
Drawer (K)
K3
Lock
STEP 8
Slide Drawer Bottom (K5) into groove.
Attach Drawer Front (K1) to unit, then flip Locks.
Part List
Roller at back
Machine Screw
Knob
Lock
K2
K4
K1
K5

Figure 9 Figure 10
Left Side Right Side
STEP 10
Turn unit from Step 5 over to its upright position.
Slide Drawers (K) and keyboard into position.
Note: To remove keyboard in future, push plastic lever on left side up, push plastic
lever on right side down and pull open. (See Figures 9 and 10)
Level unit by adjusting the adjustable levelers on bottom of unit.
(See Figure 11)
Figure 11
Assembly Instructions 6/6
K
K
Keyboard

NEVER
use glass cleaners on
finished furniture. Ammonia
chemically attacks the finish.
allow liquids to remain on furniture.
Absorption causes parts to warp
and split and finishes to delaminate.
NEVER
CARE INSTRUCTIONS
Do not use rubber
based placemats.
PREVENT
DISCOLORING
Do not use commercial
waxes and polishes.
PREVENT
YELLOWING
Do not place hot
objects on surface.
PREVENT
FINISH DAMAGE
Do not write
directly on surface.
PREVENT
MARKING
Do not use power tools
above 8 volts to assemble.
PREVENT
CRACKING
Do not place
in direct sunlight.
PREVENT
FADING
with a soft cloth moistened
in lukewarm soap and water.
Buff with a dry clean cloth.
CLEAN
homestyles will provide replacements free of charge for missing or damaged parts within 30 days of purchase.
Digital images of the defective parts may be required. If the product was not purchased from an authorized retailer,
homestyles is under no obligation to provide replacement parts. Parts are not available for fully assembled items nor
are parts available for sale. Replacements for missing or damaged parts may be requested via contact info below.
styles Customer Service: www.homestylesfurniture.com,home
[email protected], 888-680-7460