Home Styles 88 5436 09 User manual

Hardware List
Part List
Tool(s) required for assembly: Phillips screwdriver, Level, Drill (8 volts or less), 3/8” Drill Bit
Hex Wrench
1 pc.
Small Hex Wrench
1 pc.
Spring Washer
8 pcs. (+1 extra)
Flat Washer
8 pcs. (+1 extra)
Adjustable Pin
8 pcs. (+1 extra)
M3x15
Wood Screw
4 pcs. (+1 extra)
Magnet
2 pcs.
M4x28
Machine Screw
2 pcs.
Pull Handle
2 pcs.
A.
Top
1 pc.
E.
Fixed Shelf
1 pc.
F.
Base
1 pc.
G.
Back Stretcher
1 pc.
K.
Shelf
1 pc.
J.
Shelf
1 pc.
H.
Back Panel
1 pc.
I.
Back Panel
1 pc.
L.
Door
1 pc.
M.
Door
1 pc.
B.
Side Panel
1 pc.
C.
Side Panel
1 pc.
D.
Middle Panel
1 pc.
M6x35
Head Cap Bolt
8 pcs. (+1 extra)
88 5436 09
IMPORTANT
Home Styles Customer Service: www.homestyles-furniture.com,
[email protected], 888-680-7460, 877-831-0319
Carefully remove all the parts from the carton and
place them individually on a soft cloth to prevent
scratches or other damage.
Carefully and strictly follow these assembly instructions
to ensure a completed product as designed.
Do not use power tools above 8 volts to assemble.
TV Stand

Assembly Instructions 2/5
Wood Screw
Magnet
STEP 2
Attach Middle Panel (D) to Base (F), then flip the Locks. (See Figures 2 and 3)
Attach Fixed Shelf (E) to unit, then flip the Locks.
STEP 1
Attach Magnets to Fixed Shelf (E) with Wood Screws.
(See Figure 1)
Figure 1
Figure 2
Figure 3
D
IMPORTANT
Use a soft cloth between these parts and the floor.
Do not use power tools above 8 volts to assemble.
Do not tighten all the bolts until each part is properly assembled.
The unit must be level to work properly. Use the included adjustable levelers to level.
Keep Hex Wrench in a safe place as the bolts may need to be tightened up in the future.
E
F
E

Assembly Instructions 3/5
STEP 3
Attach Side Panel (B) to unit with Flat Washers,
Spring Washers and Head Cap Bolts, then flip the Locks.
(See Figure 4)
STEP 4
Attach Back Stretcher (G) to unit,
then flip the Lock.
Slide Back Panels (H) and (I) into place.
Attach Side Panel (C) to unit with Flat Washers,
Spring Washers and Head Cap Bolts, then flip
the Locks.
Figure 4
B
C
G
H
I
Flat Washer
Spring Washer
Head Cap Bolt

Assembly Instructions 4/5
A
J
K
L
Figure 5 Figure 6 Figure 7 Figure 8
STEP 5
Attach Top (A) to the unit with Flat Washers, Spring Washers and Head Cap Bolts,
then flip the Lock.
Insert Adjustable Pins into side panels and middle panel at the desired level. (See Figure 5)
Place Shelves (J) and (K) into position.
Attach Doors (L) and (M) by sliding the door lift hinges into the side panels lift hinges.
(See Figure 6)
Assemble Pull Handles to Doors (L) and (M) with Machine Screws. (See Figure 7)
To level the unit, adjust the adjustable levelers on the bottom of legs. (See Figure 8)
M

Assembly Instructions 5/5
Hardware List
STEP 6
Place unit at desired location.
Drill a 3/8” hole in wall in-line with
the pre-drilled hole at top of unit.
Move unit.
Insert Anchor into the wall hole
and attach Bracket with Wall Screw.
Attach Bracket at pre-drilled hole
at top of unit with Wood Screw.
Move unit back into place.
Slide Tipover Restraint through
Bracket on wall and Bracket on unit.
(See Figure 9)
Put tie end of Tipover Restraint into lock
end of Tipover Restraint and pull until tight.
Anchor
1 pc. (+1 extra)
Bracket
2 pcs. (+1 extra)
Tipover Restraint
1 pc. (+1 extra)
M3.5x40
Wall Screw
1 pc. (+1 extra)
M3.5x16
Wood Screw
1 pc. (+1 extra)
Figure 9
Wood Screw
Wall Screw
Bracket
on wall
Anchor in wall
3/8” wall hole
Pre-drilled hole
at top of unit
Tie end
Lock end
Bracket at
top of unit
Tipover
Restraint
Drill 3/8” hole in wall
Top of unit
IMPORTANT
To help reduce the risk of the unit tipping over, the Tipover Restraint must be installed following these instructions exactly.

NEVER
use glass cleaners on
finished furniture. Ammonia
chemically attacks the finish.
allow liquids to remain on furniture.
Absorption causes parts to warp
and split and finishes to delaminate.
NEVER
CARE INSTRUCTIONS
Do not use rubber
based placemats.
PREVENT
DISCOLORING
Do not use commercial
waxes and polishes.
PREVENT
YELLOWING
Do not place hot
objects on surface.
PREVENT
FINISH DAMAGE
Do not write
directly on surface.
PREVENT
MARKING
Do not use power tools
above 8 volts to assemble.
PREVENT
CRACKING
Do not place
in direct sunlight.
PREVENT
FADING
with a soft cloth moistened
in lukewarm soap and water.
Buff with a dry clean cloth.
CLEAN
Home Styles will provide replacements free of charge for missing or damaged hardware or parts within 30 days of
purchase. Digital images of the defective parts may be required. If the product was not purchased from an authorized
retail affiliate, Home Styles is under no obligation to provide replacement parts. Parts are not available for fully assembled
items nor are parts available for sale. Replacements for missing or damaged hardware or parts may be requested at:
www.homestyles-furniture.com/customer-service/replacement-parts
Home Styles Customer Service: www.homestyles-furniture.com,
[email protected], 888-680-7460, 877-831-0319