Home Styles 88 5170 692 User manual

Hardware List
Part List
Home Styles Customer Service: www.homestyles-furniture.com,
[email protected], 888-680-7460, 877-831-0319
IMPORTANT
Carefully remove all the parts from the carton and
place them individually on a soft cloth to prevent
scratches or other damage.
Carefully and strictly follow these assembly instructions
to ensure a completed product as designed.
Do not use power tools above 8 volts to assemble.
88 5170 692
Carton 88 5170 691 is also needed for assembly.
B.
Side Panel
1 pc.
D.
Side Panel
1 pc.
C.
Side Panel
1 pc.
E.
Side Panel
1 pc.
F.
Upright
1 pc.
G.
Upright
1 pc.
H.
Back Panel
2 pcs.
I.
Back Panel
2 pcs.
J.
Front Rail
3 pcs.
K.
Stretcher
4 pcs. O.
Door
2 pcs.
P.
Door
2 pcs.
Knob
7 pcs.
M3x15
Wood Screw
4 pcs. (+1 extra)
M3x30
Wood Screw (long)
6 pcs. (+1 extra)
M3x16
Wood Screw
for stretcher
4 pcs. (+1 extra)
Magnet
2 pcs.
M4x25
Machine Screw
7 pcs.
Adjustable Pin
16 pcs. (+1 extra)
Pantry
Tool(s) required for assembly: Phillips screwdriver, Level, Drill (8 volts or less), 3/8” Drill Bit

Wood Screw
Assembly Instructions 2/7
IMPORTANT
Use a soft cloth between these parts and the floor.
Do not use power tools above 8 volts to assemble.
The unit must be level to work properly. Use the included adjustable levelers to level.
STEP 2
Attach Side Panel (C) to unit with
Wood Screw (long) and flip the locks.
B
Wood Screw (long)
Wood Screw (long)
STEP 1
Attach Stretcher (K) to Side Panel (B),
then flip the lock. (See Figures 1 and 2)
Attach Back Panels (H), Upright (F) and
Stretcher (K) to unit, then flip the lock.
Attach Magnet to Front Rail (J) at
the pre-drilled holes with
Wood Screws. (See Figure 3)
Attach Front Rail (J) to unit
with Wood Screw (long).
Figure 1 Figure 2
C
F
H
H
JK
K
Magnet
Figure 3

Assembly Instructions 3/7
STEP 3
Turn unit to its’ upright position.
Attach Top (A) to unit, then flip the locks.
STEP 4
Attach Stretcher (K) to
Side Panel (D), then flip the lock.
Attach Back Panels (I), Upright (G)
and Stretcher (K) to unit,
then flip the lock.
Attach Magnet to Front Rail (J)
at the pre-drilled holes with Wood Screws.
Attach Front Rails (J) to unit with Wood Screws (long).
STEP 5
Attach Side Panel (E) to unit with
Wood Screws (long) and flip the locks.
A
K
K
I
I
G
JJ
D
E
Wood Screw (long)
Magnet
Wood Screw (long)

Assembly Instructions 4/7
STEP 6
Attach unit to Base (M), then flip the locks.
Attach Top (L) to unit, then flip the locks.
STEP 7
Attach unit from Step 3 to unit from Step 6,
then flip the locks.
Insert Adjustable Pins into side panels at the
desired level. (See Figure 4)
Slide Shelves (N) into position.
Figure 4
Adjustable Pin
M
L
N
N
N
N

Part List
Assembly Instructions 5/7
Drawer (Q)
STEP 8
Attach Drawer Sides (Q3) and (Q4) to
Drawer Back (Q2), then flip the locks.
(See Figures 5 and 6)
STEP 10
Attach Knobs with Machine Screws.
Figure 5 Figure 6
Roller at back
STEP 9
Slide Drawer Bottom (Q5) into the
grooves in Drawer Sides (Q3) and (Q4).
Push Drawer Bottom (Q5) all the way
into Drawer Back (Q2).
Attach Drawer Front (Q1) to unit, then flip
the locks.
Q1.
Drawer Front
1 pc.
Q2.
Drawer Back
1 pc.
Q3.
Drawer Side
1 pc.
Q4.
Drawer Side
1 pc.
Q5.
Drawer Bottom
1 pc.
Q4
Q2
Q3
Lock
Q5
Q1
Q2
Q4
Q3

Assembly Instructions 6/7
STEP 11
Level unit by adjusting
the adjustable levelers
on the bottom of unit.
(See Figure 7)
Attach Knobs to Doors (O)
and (P) with Machine Screws.
(See Figure 8)
Attach Doors (O) and (P) to
unit by sliding the door lift hinges
into the side panel lift hinges.
(See Figure 9)
Slide Drawer (Q) into place.
STEP 12
Insert Wood Screws for stretcher
into the pre-drilled holes of stretchers.
Figure 7
Figure 8
Figure 9
O
O
P
P
Q
Wood Screw
for stretcher

Assembly Instructions 7/7
Hardware List
STEP 13
Place unit at desired location.
Drill a 3/8” hole in wall in-line with
the pre-drilled hole at top of unit.
Move unit.
Insert Anchor into the wall hole
and attach Bracket with Wall Screw.
Attach Bracket at pre-drilled hole
at top of unit with Wood Screw.
Move unit back into place.
Slide Tip-over Restraint through
Bracket on wall and Bracket on unit.
(See Figure 10)
Put tie end of Tip-over Restraint into lock
end of Tip-over Restraint and pull until tight.
Anchor
1 pc. (+1 extra)
Bracket
2 pcs. (+1 extra)
Tip-over Restraint
1 pc. (+1 extra)
M3.5x40
Wall Screw
1 pc. (+1 extra)
M3.5x16
Wood Screw
1 pc. (+1 extra)
Figure 10
Wood Screw
Wall Screw
Bracket
on wall
Anchor in wall
3/8” wall hole
Pre-drilled hole
at top of unit
Tie end
Lock end
Bracket at
top of unit
Tip-over
Restraint
Drill 3/8” hole in wall
Top of unit
IMPORTANT
To help reduce the risk of the unit tipping over, the Tip-over Restraint must be installed following these instructions exactly.

NEVER
use glass cleaners on
finished furniture. Ammonia
chemically attacks the finish.
allow liquids to remain on furniture.
Absorption causes parts to warp
and split and finishes to delaminate.
NEVER
CARE INSTRUCTIONS
Do not use rubber
based placemats.
PREVENT
DISCOLORING
Do not use commercial
waxes and polishes.
PREVENT
YELLOWING
Do not place hot
objects on surface.
PREVENT
FINISH DAMAGE
Do not write
directly on surface.
PREVENT
MARKING
Do not use power tools
above 8 volts to assemble.
PREVENT
CRACKING
Do not place
in direct sunlight.
PREVENT
FADING
with a soft cloth moistened
in lukewarm soap and water.
Buff with a dry clean cloth.
CLEAN
Home Styles will provide replacements free of charge for missing or damaged hardware or parts within 30 days of
purchase. Digital images of the defective parts may be required. If the product was not purchased from an authorized
retail affiliate, Home Styles is under no obligation to provide replacement parts. Parts are not available for fully assembled
items nor are parts available for sale. Replacements for missing or damaged hardware or parts may be requested at:
www.homestyles-furniture.com/customer-service/replacement-parts
Home Styles Customer Service: www.homestyles-furniture.com,
[email protected], 888-680-7460, 877-831-0319