Home Styles 88 5527 08 User manual

Part List
Hardware List
E.
Base
1 pc.
IMPORTANT NOTE
Carefully remove all the parts from the carton and put
them individually on a soft cloth to prevent scratches
or other damages occuring to the wood parts.
We have taken great care in the design of this
product and request that you carefully and strictly
follow our assembly instructions to ensure a
completed product as it was designed.
A.
Top
1 pc.
Casual Attire For Today's Home
Cam Lock
10 pcs.(+1 extra)
Cam Lock Screw
10 pcs.(+1 extra)
88 5527 08
Homestead
Media Cabinet
F.
Plinth
1 pc.
Tools required for assembly : Phillips screwdriver
Home Styles Consumer Assistance Line 888-680-7460 and 877-831-0319
[email protected]
Pull Handle
2 pcs.
Adjustable Pin
16 pcs.(+1 extra)
Machine Screw
2 pcs.(+1 extra)
B.
Side Panel
.1 pc
C.
Side Panel
1 pc.
D.
Front Rail
.1 pc
H.
Back Panel
1 pc.
I.
Door
1 pc.
J.
Door
1 pc.
K.
Shelf
4 pcs.
G.
Leg
4 pcs.
Wood Screw
for Magnet
8 pcs.(+1 extra)
Magnet
4 pcs.
Wood Screw
for Back Panel
6 pcs.(+1 extra)
Hex Wrench
1 pc.
Head Cap Bolt
6 pcs. (+1 extra)
Small
Hex Wrench
1 pc.
Flat Washer
4 pcs. (+1 extra )
Spring Washer
4 pcs. (+1 extra )

A
Cam Lock Screw
IMPORTANT
Do not tighten up all the screws until
each part is properly assembled.
STEP 1
Assembly Instructions 2/4
D
B
C
Attach 2X Magnets
to Front Rail (D) with Wood Screws.
Insert Cam Lock Screws into the pre-drilled holes
of Top (A), .Side Panel (B) and (C)
Magnet
Wood Screw

D
STEP 3
Assembly Instructions 3/4
Cam Lock Screw
Head Cap Bolt
Cam Lock
Figure 1
E
B
C
H
STEP 2
Attach Front Rail (D) and
Base (E) to Side Panel (B)
with Cam Locks (see Figure 1).
Attach Side Panel (C) to
the unit with Cam Locks.
F
G
G
Slide Back Panel (H) into the unit
Attach Plinth (F) to the unit with Head Cap Bolts.
Attach Legs (G) into the pre-drilled holes of side panels
with Head Cap Bolts, Spring Washers and Flat Washers.
G
G
Flat Washer
Spring Washer
Head Cap Bolt

Assembly Instructions 4/4
Figure 2 Figure 3
Figure 4
STEP 4
Assemble Pull Handles to Doors (I) and (J)
with Machine Screws. (See figure 3)
Attach 2X Magnets to the pre-drilled holes at
the base of unit. (See figure 4)
Place Top (A) onto the unit, using Cam Locks.
Attach Doors (I) and (J) by sliding the door
lift hinges into the side panel lift hinges.
(See figure 2)
Insert Adjustable Pins into side panels at the
desired level. (See figure 5)
Place Shelves (K) into position.
STEP 5
Cam Lock A
J
K
K
K
K
I
Adjustable Pin
Magnet
Figure 5
Insert 6X Wood Screws from the back of the unit
and tighten. (See figure 6)
Note: Please make sure unit is level
before tightening these screws.
Figure 6