Home Styles 88 5134 307 User manual

Part List
Hardware List
IMPORTANT NOTE
Carefully remove all the parts from the carton and put
them individually on a soft cloth to prevent scratches
or other damages occuring to the wood parts.
We have taken great care in the design of this
product and request that you carefully and strictly
follow our assembly instructions to ensure a
completed product as it was designed.
88 5134 307
Hutch
Home Styles Consumer Assistance: www.homestyles-furniture.com,
[email protected], 888-680-7460, 877-831-0319
Adjustable Pin
8 pcs.(+1 extra)
Steel Plate
2 pcs.
M6x30
Head Cap Bolt
26 pcs.(+1 extra)
M6x15
Head Cap Bolt (short)
4 pcs.(+1 extra)
G.
Shelf
1 pc.
F.
Back Stretcher
1 pc.
E.
Back Stretcher
1 pc.
B.
Side Panel
.1 pc
A.
Top
.1 pc
C.
Side Panel
1 pc. H.
Divider
.1 pc
D.
Front Rail
1 pc. I.
Back Panel
2 pcs.
J.
Back Panel
1 pc.
K.
Shelf
2 pcs.
Tools required for assembly : Drill, 3/8” Drill Bit
Hex Wrench
1 pc.
Small Wrench
1 pc.

IMPORTANT
*Please keep Hex Wrench in a safe place as you may need to tighten up the Head Cap Bolts in the future.
*Do not tighten up all the Head Cap Bolts until each part is properly assembled.
*Use a soft cloth between these parts and the floor.
STEP 1
STEP 2
Assembly Instructions 2/5
Attach Back Stretcher (E) and Shelf (F) to Side Panel (B)
with Head Cap Bolts, tightening the bolts only half way.
(See Figure 1)
Attach Front Rail (D) and Side Panel (C)
to unit with Head Cap Bolts,
tightening the bolts only half way.
Tighten all Head Cap Bolts used in Steps 1 and 2.
E
Head Cap Bolt
Figure 1
B
C
D
G

STEP 3
STEP 4
Assembly Instructions 3/5
Turn unit to its’ upright position.
Attach Divider (G) to unit
with Head Cap Bolts.
Slide Back Panels (H) and (I)
into position.
Attach Back Stretcher (F)
to unit with Head Cap Bolts.
Insert Head Cap Bolts into
the pre-drilled holes of back panels.
H
I
I
F
J

Assembly Instructions 4/5
STEP 5
STEP 6
A
Adjustable Pin
Head Cap Bolt
(short)
Steel Plate
Attach Top (A) to unit
with Head Cap Bolts.
Insert Adjustable Pins into
side panels at the desired level.
Place Shelves (K)
into position.
Attach Hutch to
Buffet with Steel Plates
and Head Cap Bolts (short).
K
K

Assembly Instructions 5/5
Wood Screw
Wall Screw
Anchor
1 pc.(+1 extra)
Bracket
2 pcs.(+1 extra)
Tipover Restraint
1 pc.(+1 extra)
Hardware List
Attention!
To help reduce the risk of the unit tipping over, the Tipover Restraint be installed followingmust
these instructions exactly!
M3.5x40
Wall Screw
1 pc.(+1 extra)
tie end
loop end
Place unit at desired location.
Drill a hole in wall3/8”
at the appropriate location.
Insert Anchor into the wall hole
and attach Bracket with Wall Screw.
Attach Bracket at pre-drilled hole at top
of unit with Wood Screw.
Use Tipover Restraint to secure Bracket
on unit to Bracket on wall.
(See Figure X)
Put tie end of Tipover Restraint into loop end
of Tipover Restraint and pull until tight. Figure X
Bracket
on wall
Anchor in wall
3/8” wall hole
Bracket at
top of unit
Tipover
Restraint
Wood Screw
Wall Screw
Anchor
1 pc.(+1 extra)
Bracket
2 pcs.(+1 extra)
Tipover Restraint
1 pc.(+1 extra)
Hardware List
Attention!
To help reduce the risk of the unit tipping over, the Tipover Restraint be installed followingmust
these instructions exactly!
M3.5x40
Wall Screw
1 pc.(+1 extra)
tie end
loop end
Place unit at desired location.
Drill a hole in wall3/8”
at the appropriate location.
Insert Anchor into the wall hole
and attach Bracket with Wall Screw.
Attach Bracket at pre-drilled hole at top
of unit with Wood Screw.
Use Tipover Restraint to secure Bracket
on unit to Bracket on wall.
(See Figure X)
Put tie end of Tipover Restraint into loop end
of Tipover Restraint and pull until tight. Figure X
Bracket
on wall
Anchor in wall
3/8” wall hole
Bracket at
top of unit
Tipover
Restraint
M3.5x16
Wood Screw
1 pc.(+1 extra)
Drill 3/8” hole in wallDrill 3/8” hole in wall
Top of unit

Part List
IMPORTANT NOTE
Carefully remove all the parts from the carton and put
them individually on a soft cloth to prevent scratches
or other damages occuring to the wood parts.
We have taken great care in the design of this
product and request that you carefully and strictly
follow our assembly instructions to ensure a
completed product as it was designed.
88 5134 612
Buffet
Home Styles Consumer Assistance: www.homestyles-furniture.com,
[email protected], 888-680-7460, 877-831-0319
A.
Top
1 pc.
Tools required for assembly : Phillips screwdriver, Drill, 3/8” Drill Bit, Level
For assembly see instructions in carton 88 5134 611

Part List
Hardware List
IMPORTANT NOTE
Carefully remove all the parts from the carton and put
them individually on a soft cloth to prevent scratches
or other damages occuring to the wood parts.
We have taken great care in the design of this
product and request that you carefully and strictly
follow our assembly instructions to ensure a
completed product as it was designed.
88 5134 611
Buffet
Home Styles Consumer Assistance: www.homestyles-furniture.com,
[email protected], 888-680-7460, 877-831-0319
Adjustable Pin
12 pcs.(+1 extra)
Pull Handle
2 pcs.
M4x25
Machine Screw
2 pcs.
M4x15
Wood Screw
16 pcs.(+1 extra)
M6x30
Head Cap Bolt
32 pcs.(+1 extra)
G.
Base
1 pc.
F.
Shelf
1 pc.
I.
Back Stretcher
1 pc.
B.
Side Panel
.1 pc
C.
Side Panel
1 pc.
D.
Middle Panel
.1 pc
E.
Middle Panel
.1 pc
H.
Front Rail
1 pc.
J.
Back Panel
2 pcs.
K.
Back Panel
1 pc.
M.
Door
1 pc.
L.
Shelf
3 pcs.
N.
Door
1 pc.
Tools required for assembly : Phillips screwdriver, Drill, 3/8” Drill Bit, Level
Hex Wrench
1 pc.
Small Wrench
1 pc.
Also need the parts in carton 88 5134 612
Magnet
2 pcs.

IMPORTANT
*Please keep Hex Wrench in a safe place as you may need to tighten up the Head Cap Bolts in the future.
*Do not tighten up all the screws until each part is properly assembled.
*After assembly item must be level to work properly. Use the included adjustable levelers to level.
*Use a soft cloth between these parts and the floor.
STEP 1
STEP 2
Assembly Instructions 2/5
Attach Magnets to Shelf (F) with Wood Screws.
(See Figure 1)
Attach Middle Panels (D) and (E) to Shelf (E)
with Head Cap Bolts,
tightening the bolts
only half way.
Attach Base (G) to unit
with Head Cap Bolts,
tightening the bolts
only half way.
(See Figure 2)
Attach Side Panel (B) and Front Rail (H)
to unit with Head Cap Bolts, tightening the bolts
only half way.
Attach Side Panel (C) to unit with Head Cap Bolts, tightening the bolts only half way.
Tighten all Head Cap Bolts used in Steps 1 and 2.
F
D
E
G
B
C
H
Head Cap Bolt
Magnet
Figure 1 Figure 2

STEP 3
STEP 4
Assembly Instructions 3/5
Turn unit to its’ upright position.
Slide Back Panels (J) and (K)
into position.
Attach Back Stretcher (I) to unit with Head Cap Bolts.
Insert Head Cap Bolts into the pre-drilled holes of back panels.
J
KJ
I

Figure 4 Figure 5
Assembly Instructions 4/5
Figure 3
STEP 5
A
L
L
L
M
N
Adjustable PinWood Screw Machine Screw
Attach Top (A) to unit with Head Cap Bolts.
Insert Adjustable Pins into side panels and middle panels at the desired level.
Place Shelves (L) into position.
Attach Doors (M) and (N) to unit with Wood Screws. (See Figure 3)
Assemble Pull Handles to Doors (M) and (N) with Machine Screws. (See Figure 4)
To level the unit, adjust the adjustable levelers on the bottom of legs. (See Figure 5)
Note : Unit must be level to work properly.