Home Styles 20 05506 0681 User manual

Hardware List
Part List
Home Styles Customer Service: www.homestyles-furniture.com,
[email protected], 888-680-7460, 877-831-0319
Tool(s) required for assembly: Phillips screwdriver, Level, Drill (8 volts or less), 3/8” Drill Bit
IMPORTANT
M4x25
Machine Screw
4 pcs.
Handle
5 pcs.
Carefully remove all the parts from the carton and
place them individually on a soft cloth to prevent
scratches or other damage.
Carefully and strictly follow these assembly instructions
to ensure a completed product as designed.
Do not use power tools above 8 volts to assemble.
Carton 20 05506 0682 is also needed for assembly.
M x3.5 15
Wood Screw (short)
12 pcs. (+1 extra)
Adjustable Pin
24 pcs. (+1 extra)
Hinge
4 pcs.
Cam Lock Screw
26 pcs. (+2 extra)
M x3.5 25
Wood Screw (long)
31 pcs. (+1 extra)
M x630
Head Cap Bolt
4 pcs. (+1 extra)
Cam Lock
26 pcs. (+4 extra)
20 05506 0681
Buffet
Hex Wrench
1 pc.
M4x35
Machine Screw (long)
6 pcs.
M x13.5 5
Wood Screw
for Hinge
24 pcs. (+1 extra)
Small
Hex Wrench
1 pc.
A.
Top
1 pc.
B.
Side Panel
1 pc.
C.
Side Panel
1 pc.
D.
Middle Panel
1 pc.
E.
Middle Panel
1 pc.
G.
Door
1 pc.
F.
Door
1 pc.

IMPORTANT
Use a soft cloth between these parts and the floor.
Do not use power tools above 8 volts to assemble.
Do not tighten all the screws unit each part is properly assembled.
The unit must be level to work properly. Use the included adjustable levelers to level.
Keep Hex Wrench as the bolts may need to be tightened in the future.
Assembly Instructions 2/11
Figure 1
STEP 1
Insert Cam Lock Screws into pre-drilled holes in Top (A),
Side Panels (B), (C), and Back Panel (L), then tighten.
(See Figure 1)
B
C
L
A
Cam Lock Screw
Cam Lock Screw

Assembly Instructions 3/11
STEP 2
Attach Middle Panels (D), (E)
to Top (A) with Cam Locks.
(See Figure 2)
STEP 4
Attach unit from Step 3
to unit from Step 2 with
Head Cap Bolts.
Head Cap Bolt
A
Cam Lock
Wood Screw (long)
I
E
H
D
STEP 3
Attach Plinth (I) to Bottom (H)
with Wood Screws (long), then tighten.
Figure 2

Assembly Instructions 4/11
STEP 6
Attach Side Panels (B) and (C) to unit
with Cam Locks and Wood Screws (long).
STEP 5
Attach Back Panel (K) to unit
with Cam Locks.
Attach Back Panel (L) to unit
with Cam Locks.
Wood Screw (long)
Cam Lock
Cam Lock
B
K
L
C

Assembly Instructions 5/11
STEP 8
Turn unit to its upright position.
Attach Doors (F) and (G) to unit
with Wood Screws for Hinge into
pre-drilled holes, then tighten.
(See Figure 4)
Attach Handles to Doors (F)
and (G) with Machine Screws.
Figure 4
STEP 7
Attach Hinges to Doors (F) and (G) with Wood Screws
for Hinge into pre-drilled holes, then tighten.
(See Figure 3)
Figure 3
Wood Screw for Hinge
Hinge
Handle
Machine Screw
Wood Screw for Hinge
G
F
G
F

Part List
Assembly Instructions 6/11
STEP 11
Attach Handle with Machine Screws (long).
Drawer (M)
STEP 10
Slide Drawer Bottom (M5) into groove.
Attach Drawer Bottom (M5) to
unit with Wood Screws (short).
M1.
Drawer Front
1 pc.
M2.
Drawer Back
1 pc.
M5.
Drawer Bottom
1 pc.
M3.
Drawer Side
1 pc.
M4.
Drawer Side
1 pc.
STEP 9
Attach Drawer Front (M1) and Drawer
Back (M2) to Drawer Side (M3)
with Wood Screws (long).
Attach Drawer Side (M4) to unit
with Wood Screws (long).
M5
Bottom
Wood Screw (long)
Machine Screw (long)
Handle
Wood Screw (short)
Roller at back
M1
M2
M4
M3

Part List
Assembly Instructions 7/11
STEP 14
Attach Handle with Machine Screws (long).
Drawer (N)
STEP 13
Slide Drawer Bottom (N5) into groove.
Attach Drawer Bottom (N5) to
unit with Wood Screws (short).
N1.
Drawer Front
1 pc.
N2.
Drawer Back
1 pc.
N5.
Drawer Bottom
1 pc.
M3.
Drawer Side
1 pc.
M4.
Drawer Side
1 pc.
STEP 12
Attach Drawer Front (N1) and Drawer
Back (N2) to Drawer Side (M3)
with Wood Screws (long).
Attach Drawer Side (M4) to unit
with Wood Screws (long).
N5
Bottom
Wood Screw (long)
Machine Screw (long)
Handle
N1
M3
N2
M4
Wood Screw (short)
Roller at back

Part List
Assembly Instructions 8/11
STEP 17
Attach Handle with Machine Screws (long).
Drawer (O)
STEP 16
Slide Drawer Bottom (M5) into groove.
Attach Drawer Bottom (M5) to
unit with Wood Screws (short).
O1.
Drawer Front
1 pc.
M2.
Drawer Back
1 pc.
M5.
Drawer Bottom
1 pc.
M3.
Drawer Side
1 pc.
M4.
Drawer Side
1 pc.
STEP 15
Attach Drawer Front (O1) and Drawer
Back (M2) to Drawer Side (M3)
with Wood Screws (long).
Attach Drawer Side (M4) to unit
with Wood Screws (long).
M5
Bottom
Wood Screw (long)
Machine Screw (long)
Handle
O1
M2
M4
M3
Wood Screw (short)
Roller at back

Assembly Instructions 9/11
STEP 18
Slide Drawers (M), (N) and (O) into position.
Insert Adjustable Pins into side panels and middle panels at desired level.
(See Figure 5)
Place Shelves (J) into position.
Level unit by adjusting the adjustable levelers on bottom of unit.
(See Figure 6)
Adjustable Pin NO
J
M
J
J
J
J
J
Figure 6
Figure 5

Assembly Instructions 10/11
STEP 19
If needed, adjust doors up or down by removing the front Wood Screws for Hinge and
loosening slightly the back Wood Screws for Hinge from side panel, adjusting doors up or down
and reinstalling screws. (See Figure 7)
If needed, adjust doors left to right. (See Figure 8)
If needed, adjust doors front to back. (See Figure 9)
Figure 8
Figure 7
Figure 7
Up
Down
Left
Right
Front Back
Figure 9
Figure 8

Hardware List
Assembly Instructions 11/11
Drill 3/8” hole in wall
Top of unit
STEP 20
Place unit at desired location.
Drill a 3/8” hole in wall in-line with
Pre-drilled hole at top of unit.
Move unit.
Insert Anchor into the wall hole
and attach Bracket with Wall Screw.
Attach Bracket at pre-drilled hole
at top of unit with Wood Screw.
Move unit back into place.
Slide Tipover Restraint through
Bracket on wall and Bracket on unit.
(See Figure 10)
Put tie end of Tipover Restraint into lock
end of Tipover Restraint and pull until tight. Figure 10
Bracket
on wall
Anchor in wall
3/8” wall hole
Tie end
Lock end
Bracket at
top of unit
Tipover
Restraint
Wood Screw
Wall Screw Pre-drilled hole
at top of unit
Anchor
1 pc. (+1 extra)
Bracket
2 pcs. (+1 extra)
M3.5x40
Wall Screw
1 pc. (+1 extra)
M3.5x16
Wood Screw
1 pc. (+1 extra)
IMPORTANT
To help reduce the risk of the unit tipping over, the Tipover Restraint must be installed following these instructions exactly.
Tipover Restraint
1 pc. (+1 extra)

NEVER
use glass cleaners on
finished furniture. Ammonia
chemically attacks the finish.
allow liquids to remain on furniture.
Absorption causes parts to warp
and split and finishes to delaminate.
NEVER
CARE INSTRUCTIONS
Do not use rubber
based placemats.
PREVENT
DISCOLORING
Do not use commercial
waxes and polishes.
PREVENT
YELLOWING
Do not place hot
objects on surface.
PREVENT
FINISH DAMAGE
Do not write
directly on surface.
PREVENT
MARKING
Do not use power tools
above 8 volts to assemble.
PREVENT
CRACKING
Do not place
in direct sunlight.
PREVENT
FADING
with a soft cloth moistened
in lukewarm soap and water.
Buff with a dry clean cloth.
CLEAN
Home Styles will provide replacements free of charge for missing or damaged hardware or parts within 30 days of
purchase. Digital images of the defective parts may be required. If the product was not purchased from an authorized
retail affiliate, Home Styles is under no obligation to provide replacement parts. Parts are not available for fully assembled
items nor are parts available for sale. Replacements for missing or damaged hardware or parts may be requested at:
www.homestyles-furniture.com/customer-service/replacement-parts
Home Styles Customer Service: www.homestyles-furniture.com,
[email protected], 888-680-7460, 877-831-0319