Home Styles 6801-101 User manual

Hardware List
Part List
6801-101
IMPORTANT
Carefully remove all the parts from the carton and
place them individually on a soft cloth to prevent
scratches or other damage.
Carefully and strictly follow these assembly instructions
to ensure a completed product as designed.
Do not use power tools above 8 volts to assemble.
Arm Chair
A.
Back
1 pc.
B.
Seat
1 pc.
C.
Side
2 pcs.
E.
Foot
4 pcs.
Small
Hex Wrench
1 pc.
Hex Wrench
1 pc.
Spring Washer
24 pcs. (+1 extra)
M6x35
Head Cap Bolt
24 pcs. (+1 extra)
Flat Washer
24 pcs. (+1 extra)
Carton 6801-CUS is also need for assembly.
styles Customer Service: www.homestylesfurniture.com,home
[email protected], 888-680-7460

Assembly Instructions 2/5
IMPORTANT
Use a soft cloth between these parts and the floor.
Do not use power tools above 8 volts to assemble.
Do not tighten all the bolts until each part is properly assembled.
The unit must be level to work properly. Use the included adjustable levelers to level.
Keep Hex Wrench as the bolts may need to be tightened in the future.
STEP 1
Attach Seat (B) to Back (A) with Head Cap Bolts,
Spring Washers and Flat Washers,
tightening bolts only halfway.
(See Figure 1)
STEP 2
Attach to Side (C) withunit
Head Cap Bolts, Spring Washers and
Flat Washers, tightening bolts only halfway.
(See Figure 2)
Flat Washer
Spring Washer
Head Cap Bolt
Head Cap Bolt
Spring Washer
Flat Washer
B
A
Figure 1
C
Figure 2

Assembly Instructions 3/5
STEP 4
Attach unit to Side (C) with
Head Cap Bolts, Spring Washers and
Flat Washers, tightening bolts only halfway.
STEP 3
Insert Head Cap Bolts, Spring Washers
and Flat Washers into unit, tightening bolts
only halfway.
(See Figure 3)
Head Cap Bolt
Spring Washer
Flat Washer
C
Figure 3
Head Cap Bolt
Spring Washer
Flat Washer

Assembly Instructions /45
STEP 5
Insert Head Cap Bolts,
Spring Washers and Flat Washers
into unit, tightening bolts only halfway.
Tighten all bolts used in Steps 1, 2, 3, 4 and 5.
STEP 6
Attach Feet (E) to unit with
Head Cap Bolts, Spring Washers
and Flat Washers.
(See Figure 4)
Head Cap Bolt
Spring Washer
Flat Washer
Head Cap Bolt
Spring Washer
Flat Washer
Figure 4
E
E
E
E

Assembly Instructions /55
STEP 7
Turn over unit to its upright position.
Attach Seat Cushion (F) to unit by pushing toggles through weaving in back of unit.
(See Figure 5)
Place Back Cushion (G) into position.
Level unit by adjusting the adjustable levelers on bottom of unit.
(See Figure 6)
Figure 5
Toggle
F
Figure 6
G
Toggle

NEVER
use glass cleaners on
finished furniture. Ammonia
chemically attacks the finish.
allow liquids to remain on furniture.
Absorption causes parts to warp
and split and finishes to delaminate.
NEVER
CARE INSTRUCTIONS
Do not use rubber
based placemats.
PREVENT
DISCOLORING
Do not use commercial
waxes and polishes.
PREVENT
YELLOWING
Do not place hot
objects on surface.
PREVENT
FINISH DAMAGE
Do not write
directly on surface.
PREVENT
MARKING
Do not use power tools
above 8 volts to assemble.
PREVENT
CRACKING
Do not place
in direct sunlight.
PREVENT
FADING
with a soft cloth moistened
in lukewarm soap and water.
Buff with a dry clean cloth.
CLEAN
homestyles will provide replacements free of charge for missing or damaged parts within 1 year of purchase.
Digital images of the defective parts may be required. If the product was not purchased from an authorized retailer,
homestyles is under no obligation to provide replacement parts. Parts are not available for fully assembled items nor
are parts available for sale. Replacements for missing or damaged parts may be requested via contact info below.
styles Customer Service: www.homestylesfurniture.com,home
[email protected], 888-680-7460