Home Styles 6658-53 User manual

6658-53
Swivel Chair
IMPORTANT
Carefully remove all the parts from the carton and place them
individually on a soft cloth to prevent scratches or other damage.
Carefully and strictly follow these assembly instructions
to ensure a completed product as designed.
This product is made of aluminum. Do not use power tools
above 8 volts to assemble and only tighten bolts until snug.
Over tightening can damage the aluminum.
D.
Cushion
1 pc.
Part List
styles Customer Service: www.homestylesfurniture.com,home
[email protected], 888-680-7460
Hardware List
Wrench
1 pc.
Flat Washer (long)
4 pcs. (+1 extra)
M8x35
Bolt
4 pcs. (+1 extra)
Spring Washer (large)
4 pcs. (+1 extra)
Spring Washer
10 pcs. (+1 extra)
Nut
4 pcs. (+1 extra)
Cap (large)
8 pcs. (+1 extra)
Cap
10 pcs. (+1 extra)
M6x20
Head Cap Bolt
10 pcs. (+1 extra)
Flat Washer
10 pcs. (+1 extra)
Small
Hex Wrench
1 pc.
Hex Wrench
1 pc.
C.
Base
1 pc.
B.
Connector
1 pc.
H.
Arm
1 pc.
G.
Arm
1 pc.
F.
Back
1 pc.
E.
Seat
1 pc.

Assembly Instructions 2/5
IMPORTANT
Use a soft cloth between these parts and the floor.
Do not use power tools above 8 volts to assemble.
Do not tighten all the bolts until each part is properly assembled.
The unit must be level to work properly. Use the included adjustable levelers to level.
Keep Wrench as the bolts may need to be tightened in the future.
STEP 1
Attach Back (F) to Seat (E) with Flat Washers, Spring Washers and Head Cap Bolts,
tightening bolts only halfway.
(See Figure 1)
Figure 1
Head Cap Bolt
Spring Washer
Flat Washer
F
E

Assembly Instructions /35
STEP 2
Place Arm (H) on a soft cloth.
Attach unit to Arm (H) with Flat Washers,
Spring Washers and Head Cap Bolts,
tightening bolts only halfway.
STEP 3
Place Arm (G) on a soft cloth.
Attach unit to Arm (G)
with Flat Washers, Spring Washers and
Head Cap Bolts, tightening bolts only halfway.
Tighten all Bolts used in Steps 1 and 2.
Cover all Head Cap Bolts with Caps.
Flat Washer
Spring Washer
Head Cap Bolt
Cap
Flat Washer
Spring Washer
Head Cap Bolt
G
H

Assembly Instructions 4/5
Figure 2
Cap (large)
Bolt
Flat Washer (long)
Seat (A)
Cap
Connector (B)
Flat Washer (long)
Spring Washer (large)
Nut
B
STEP 4
Attach unit to Connector (B) with Bolts,
Flat Washers (long), Spring Washers (large)
and Nuts, tightening bolts and nuts only halfway.
(See Figure 2)
Tighten all Bolts and Nuts.
Cover all Bolts and Nuts with Caps (large).

Assembly Instructions 5/5
STEP 5
Place unit onto Base (C).
Place Cushion (D) onto unit.
STEP 6
Use velcro on Cushion (D) to attach to unit.
(See Figure 2)
D
Figure 2
C
Velcro
D

NEVER
use glass cleaners on
finished furniture. Ammonia
chemically attacks the finish.
allow liquids to remain on furniture.
Absorption causes parts to warp
and split and finishes to delaminate.
NEVER
CARE INSTRUCTIONS
Do not use rubber
based placemats.
PREVENT
DISCOLORING
Do not use commercial
waxes and polishes.
PREVENT
YELLOWING
Do not place hot
objects on surface.
PREVENT
FINISH DAMAGE
Do not write
directly on surface.
PREVENT
MARKING
Do not use power tools
above 8 volts to assemble.
PREVENT
CRACKING
Do not place
in direct sunlight.
PREVENT
FADING
with a soft cloth moistened
in lukewarm soap and water.
Buff with a dry clean cloth.
CLEAN
homestyles will provide replacements free of charge for missing or damaged parts within 2 years of purchase.
Digital images of the defective parts may be required. If the product was not purchased from an authorized retailer,
homestyles is under no obligation to provide replacement parts. Parts are not available for fully assembled items nor
are parts available for sale. Replacements for missing or damaged parts may be requested via contact info below.
styles Customer Service: www.homestylesfurniture.com,home
[email protected], 888-680-7460