Home Styles 20 05530 0565 User manual

Hardware List
Part List
Home Styles Customer Service: www.homestyles-furniture.com,
[email protected], 888-680-7460, 877-831-0319
Tool(s) required for assembly: Phillips screwdriver
IMPORTANT
Carefully remove all the parts from the carton and
place them individually on a soft cloth to prevent
scratches or other damage.
Carefully and strictly follow these assembly instructions
to ensure a completed product as designed.
Do not use power tools above 8 volts to assemble.
20 05530 0565
Bunk Bed
Small Hex Wrench
1 pc.
Hex Wrench
1 pc.
Carton 20 05530 0564 is also needed for assembly.
S2.
Back Panel
1 pc.
S3.
Back Panel
1 pc.
S5.
Back Panel
1 pc.
T1.
Stair Panel
1 pc.
T2.
Stair Panel
1 pc.
T3.
Stair Panel
4 pcs.
U2.
Rail
2 pcs.
V.
Stair Rail
1 pc.
W.
Upright
1 pc.
Refer to later page(s) of these
instructions for drawer assembly.
X.
Drawer
4 pcs.
U1.
Rail
2 pcs.
Cam Lock Screw
32 pcs. (+1 extra)
Cam Lock
32 pcs. (+4 extra)
M4x1”
Machine Screw
4 pcs.
Knob (22mm)
4 pcs.
M6x30
Head Cap Bolt (short)
21 pcs. (+1 extra)
M6x55
Head Cap Bolt (medium)
1 pcs. (+1 extra)
M6x25
Wood Screw for Drawer
32 pcs. (+1 extra)
M6x45
Head Cap Bolt for Bed
3 pcs. (+1 extra)

Assembly Instructions 2/10
IMPORTANT
Use a soft cloth between these parts and the floor.
Do not use power tools above 8 volts to assemble.
Do not tighten all the bolts until each part is properly assembled.
The unit must be level to work properly. Use the included adjustable levelers to level.
Keep Hex Wrench as the bolts may need to be tightened in the future.
STEP 11
Insert Cam Lock Screws into pre-drilled holes in Stairs (M1), (M2), (M3), (M4), (M5), Base (N),
Side Panel (O) and Risers (P2), (P3), then tighten. (See Figure 6)
Follow instructions in carton 20 05530 0563 first, then proceed with Step 11.
Figure 6
M4
M3
M1
M5
M2 Cam Lock Screw
N
P2
P3
O
Cam Lock Screw

Assembly Instructions 3/10
STEP 12
Attach Base (N) to Side Panel (O)
with Cam Locks. (See Figure 7)
Note: A Philips screwdriver 5” or
less in length is recommended.
O
N
Figure 7
Cam Lock
STEP 13
Attach Rail (U1) and Middle Panel (R) to unit.
STEP 14
Attach Rail (U1) to unit.
Attach Riser (P2) to unit with Cam Locks.
U1
R
Cam Lock
P2
U1

Assembly Instructions 4/10
STEP 15
Attach Stair (M5) to Riser (P3) with Cam Locks.
Cam Lock
Cam Lock
S4
M4
STEP 17
Turn unit to its’ upright position.
Slide Back Panel (S4) into position.
Attach Stair (M4) to unit with Cam Locks.
Cam Lock
STEP 16
Attach Rails (U2) to unit from Step 14.
Slide Back Panel (S5) into position.
Attach unit from Step 15 to unit with Cam Locks.
P3
M5
U2
U2 S5

Assembly Instructions 5/10
Cam Lock
STEP 18
Attach Riser (P1) and Divider (Q)
to unit with Cam Locks.
P1
Q
STEP 19
Slide Back Panel (S3) into position.
Attach Stair (M3) to unit with Cam Locks.
Cam Lock
M3
S3
STEP 20
Attach Riser (P1) and Divider (Q)
to unit with Cam Locks.
P1
Q
Cam Lock

Assembly Instructions 6/10
M2
S2
Cam Lock
STEP 21
Slide Back Panel (S2) into position.
Attach Stair (M2) to unit with Cam Locks.
STEP 22
Attach Riser (P1) to unit with Cam Locks.
P1
Cam Lock
STEP 23
Slide Back Panel (S1) into position.
Attach Stair (M1) to unit with Cam Locks.
S1
Cam Lock
M1

Assembly Instructions 7/10
W
T3
T3
T3
T3
V
STEP 24
Assemble Stair Panels (T3), Stair Rail (V)
and Upright (W) with Head Cap Bolts (short),
tightening bolts only halfway.
Head Cap Bolt (short)
Figure 8
STEP 25
Attach unit from Step 24 and Stair Panel (T2)
to unit from Step 23 with Head Cap Bolts (short),
tightening bolts only halfway.
Head Cap Bolt (short)
T2
Head Cap Bolt (short)
Head Cap Bolt (medium)
STEP 26
Attach Head Cap Bolt (medium) to unit,
tightening bolt only halfway.
Attach Stair Panel (T1) to unit with
Head Cap Bolts (short), tightening bolts
only halfway.
Tighten all bolts used in Steps 24, 25 and 26.
T1

Part List
STEP 29
Attach Knob (22mm) with Machine Screw.
X1.
Drawer Front
4 pcs.
X2.
Drawer Back
4 pcs.
X3.
Drawer Side
4 pcs.
X4.
Drawer Side
4 pcs.
X5.
Drawer Bottom
4 pcs.
Machine Screw
STEP 28
Slide Drawer Bottom (X5) into grooves in unit.
Attach Drawer Side (X4) to
unit with Wood Screws for Drawer.
Assembly Instructions 8/10
Knob (22mm)
Drawer (X)
Roller at back
X2
X3
Wood Screw for Drawer
X1
STEP 27
Attach Drawer Front (X1) and Drawer
Back (X2) to Drawer Side (X3) with
Wood Screws for Drawer.
X4
X5
Wood Screw for Drawer

STEP 30
Attach unit from Step 24 to bunk bed unit with Head Cap Bolts for Bed and Head Cap Bolt (short),
tightening bolts only halfway.
Tighten all bolts.
Slide Drawers (X) into position.
Assembly Instructions 9/10
Head Cap Bolt for Bed
Head Cap Bolt (short)
X
X
X
X

Assembly Instructions 10/10
STEP 31
Place unit at desired location.
Drill a 3/8” hole in wall in-line with
pre-drilled hole on back of Stair Panel (T1).
Move unit.
Insert Anchor into the wall hole
and attach Bracket with Wall Screw.
Attach Bracket at pre-drilled
hole on back of Stair Panel (T1)
with Wood Screw.
Move unit back into place.
Slide Tip-over Restraint through
Bracket on wall and Bracket on unit.
(See Figure 9)
Put tie end of Tip-over Restraint into lock
end of Tip-over Restraint and pull until tight.
IMPORTANT
To help reduce the risk of the unit tipping over, the Tip-over Restraint must be installed following these instructions exactly.
Figure 9
Wood Screw
Wall Screw
Bracket
on wall
Anchor in wall
3/8” wall hole
Pre-drilled hole on
back of Stair Panel (T1)
Tie end
Lock end
Bracket on back
of Stair Panel (T1)
Tip-over
Restraint
Anchor
1 pc. (+1 extra)
Bracket
2 pcs. (+1 extra)
Tip-over Restraint
1 pc. (+1 extra)
M3.5x38
Wall Screw
1 pc. (+1 extra)
M3.5x16
Wood Screw
1 pc. (+1 extra)
Drill 3/8” hole in wall
Back of Stair Panel (T1)
T1