Home Styles 20 08000 0101 User manual

Hardware List
Part List
9
Tool(s) required for assembly: Phillips screwdriver, Level, Drill (8 volts or less), 3/8” Drill Bit
IMPORTANT
Carefully remove all the parts from the carton and
place them individually on a soft cloth to prevent
scratches or other damage.
Carefully and strictly follow these assembly instructions
to ensure a completed product as designed.
Do not use power tools above 8 volts to assemble.
Carton 20 08000 0102 is also needed for assembly.
20 08000 0101
Entertainment Stand
O.
Drawer
1 pc.
A.
Top
1 pc.
I.
Base
1 pc.
J.
Plinth
2 pcs.
K.
Plinth
2 pcs.
F.
Shelf
1 pc.
N.
Shelf
5 pcs.
L.
Cleat
1 pc.
Refer to later page(s) of these
instructions for drawer assembly.
Cam Lock Screw
26 pcs. (+2 extra)
Cam Lock
20 pcs. (+6 extra)
Cam Lock (small)
6 pcs. (+1 extra)
M3.5x14
Wood Screw
for Hinge
24 pcs. (+1 extra)
M3.5x38
Wood Screw
8 pcs. (+1 extra)
M3.5x64
Wood Screw (long)
16 pcs. (+1 extra)
M3.5x25
Wood Screw (short)
7 pcs. (+1 extra)
Dowel
26 pcs. (+1 extra)
Adjustable Pin
20 pcs. (+1 extra)
Hinge
4 pcs.
M3x20
Wood Screw
for Plastic Clip
1 pcs. (+1 extra)6
Plastic Clip
1 pcs. (+1 extra)6

Assembly Instructions 2/8
IMPORTANT
Use a soft cloth between these parts and the floor.
Do not use power tools above 8 volts to assemble.
Do not tighten all the screws until each part is properly assembled.
The unit must be level to work properly. Use the included adjustable levelers to level.
STEP 2
Attach Middle Panels (D) and (E) to Shelf (F)
with Dowels and Cam Locks. (See Figure 3)
STEP 1
Insert Cam Lock Screws into pre-drilled holes
in Top (A), Middle Panels (D), (E) and Plinths (J),
then tighten. (See Figure 1)
Attach Cleat (L) to Top (A) with
Wood Screws (short) into pre-drilled holes.
(See Figure 2)
Figure 1 Figure 2
Figure 3
A
D
E
Cam Lock Screw
Cam Lock
Wood Screw (short)
Dowel
F
D
E
J
J
L

Assembly Instructions 3/8
A
B
C
Cam Lock
Wood Screw
Dowel
Dowel
STEP 3
Place Top (A) upside down on a soft cloth.
Attach Side Panels (B), (C) and unit to Top (A)
with Dowels and Cam Locks.
STEP 4
Slide Back Panels (G)
and (H) into position.
Attach Base (I) to unit
with Dowels and Wood Screws into pre-drilled holes.
G
H
H
I

Assembly Instructions 4/8
J
J
STEP 5
Attach Plinths (J) to Plinths (K)
with Cam Locks. (See Figure 4)
STEP 6
Attach unit from Step 5 to unit from Step 4
with Dowels and Wood Screws (long) into pre-drilled holes.
Figure 4
Cam Lock
Dowel
Wood Screw (long)
K
K

Assembly Instructions 5/8
O3.
Drawer Side
1 pc.
O4.
Drawer Side
1 pc.
O5.
Drawer Bottom
1 pc.
O6.
Support
1 pc.
O1.
Drawer Front
1 pc.
O2.
Drawer Back
1 pc.
Wood Screw (short)
Cam Lock Screw
Cam Lock (small)
Drawer (O)
STEP 7
Attach Drawer Sides (O3) and (O4) to
Drawer Back (O2) with Wood Screws (short).
STEP 9
Insert Cam Lock Screws into
pre-drilled holes in Drawer Front (O1), then tighten.
Attach Drawer Front (O1) to drawer unit with Cam Locks (small).
Wood Screw (short)
O4
O4
O4
O1
O2
O2
O2
O3
O3
O3
O5
O5
O6
O6
STEP 8
Slide Drawer Bottom (O5) into grooves
in Drawer Sides (O3) and (O4) until it meets
Drawer Back (O2).
Attach Support (O6) to unit with Wood Screws (short).

Assembly Instructions 6/8
M
M
STEP 10
Place Doors (M) upside down on a soft cloth.
Attach Hinges to Doors (M) with Wood Screws for Hinge into pre-drilled holes, then tighten.
(See Figure 5)
Figure 5
Wood Screw
for Hinge
Hinge
Wood Screw
for Hinge
M
M
O
STEP 11
Attach Doors (M) to unit with Wood Screws for Hinge.
(See Figure 6)
Slide Drawer (O) into position. Figure 6

Assembly Instructions 7/8
STEP 12
Insert Adjustable Pins into side panels and middle panels
at desired level. (See Figure 7)
Place Shelves (N) into position.
Figure 7
Figure 8
Figure 10 Figure 11
UP Front Back
Down
Figure 12
Left
Right
STEP 14
If needed, adjust doors up or down by removing the front Wood Screws for Hinge and
loosening slightly the back Wood Screws for Hinge from side panel, adjusting doors up or down
and re-installing screws. (See Figure 10).
If needed, adjust doors left to right. (See Figure 11)
If needed, adjust doors front to back. (See Figure 12)
NN
NN
N
Adjustable Pin
Wood Screw
for Plastic Clip
Figure 9
STEP 13
Level unit by adjusting the
adjustable levelers on bottom
of unit. (See Figure 8)
Attach Plastic Clips to unit with
Wood Screws for Plastic Clip. (See Figure 9)
Note: Unit must be level before attaching
these Plastic Clips.
Plastic Clip

Assembly Instructions 8/8
Hardware List
STEP 15
Place unit at desired location.
Drill a 3/8” hole in wall in-line with
pre-drilled hole at top of unit.
Move unit.
Insert Anchor into the wall hole
and attach Bracket with Wall Screw.
Attach Bracket at pre-drilled hole
at top of unit with Wood Screw.
Move unit back into place.
Slide Tip-over Restraint through
Bracket on wall and Bracket on unit.
(See Figure 13)
Put tie end of Tip-over Restraint into lock
end of Tip-over Restraint and pull until tight.
Figure 13
Wood Screw
Wall Screw
Bracket
on wall
Anchor in wall
3/8” wall hole
Pre-drilled hole
at top of unit
Tie end
Lock end
Bracket at
top of unit
Tip-over
Restraint
IMPORTANT
To help reduce the risk of the unit tipping over, the Tip-over Restraint must be installed following these instructions exactly.
Anchor
1 pc. (+1 extra)
Bracket
2 pcs. (+1 extra)
Tip-over Restraint
1 pc. (+1 extra)
M3.5x38
Wall Screw
1 pc. (+1 extra)
M3x16
Wood Screw
1 pc. (+1 extra)
Drill 3/8” hole in wall
Top of unit

NEVER
use glass cleaners on
finished furniture. Ammonia
chemically attacks the finish.
allow liquids to remain on furniture.
Absorption causes parts to warp
and split and finishes to delaminate.
NEVER
CARE INSTRUCTIONS
Do not use rubber
based placemats.
PREVENT
DISCOLORING
Do not use commercial
waxes and polishes.
PREVENT
YELLOWING
Do not place hot
objects on surface.
PREVENT
FINISH DAMAGE
Do not write
directly on surface.
PREVENT
MARKING
Do not use power tools
above 8 volts to assemble.
PREVENT
CRACKING
Do not place
in direct sunlight.
PREVENT
FADING
with a soft cloth moistened
in lukewarm soap and water.
Buff with a dry clean cloth.
CLEAN
Home Styles will provide replacements free of charge for missing or damaged hardware or parts within 30 days of
purchase. Digital images of the defective parts may be required. If the product was not purchased from an authorized
retail affiliate, Home Styles is under no obligation to provide replacement parts. Parts are not available for fully assembled
items nor are parts available for sale. Replacements for missing or damaged hardware or parts may be requested at: