Home Styles Dolly Madison 88 4528 95 User manual

Head Cap Bolt
12 pcs. (+1extra)
Head Cap Bolt (long)
7 pcs. (+1extra)
Cross Dowel
7 pcs. (+1extra)
Hex Wrench
1 pc.
Machine Screw
for Pull Handle
12 pcs.
Pull Handle
6 pcs.
Adjustable Pin
8 pcs. (+1 extra)
Wood Plug
9 pcs.
(+1 extra)
Caster
two lock
two non-lock
4 pcs.
88 4528 95
Wood Top Kitchen Cart
(Black Finish)
PART LIST
HARDWARE LIST
IMPORTANT NOTE
Carefully remove all the parts from the carton and put them individually
on a soft cloth to prevent scratches or other damages occuring to the wood parts.
We have taken great care in the design of this product and request that you carefully
and strictly follow our assembly instructions to ensure a completed product as it was designed.
P.
Door
2 pcs.
O.
Door
2 pcs.
C.
Middle Panel
1 pc.
D.
Side Panel
1 pc.
E.
Back Stretcher
2 pcs.
A.
Top
1 pc.
M.
Side Bar
2 pcs.
N.
Shelf
2 pcs.
B.
Side Panel
1 pc.
K.
Divider
1 pc.
L.
Base
1 pc.
F.
Back Piece
1 pc.
G.
Back Piece
2 pcs.
Q.
KD. Drawer
2 pcs.
(Knock-Down Construction,
please refer to the last page of
instructions for steps to complete
assembling drawers)
Wood Screw (short)
for Drawer Base Part
12 pcs. (+1 extra)
Wood Screw (long)
for Drawer Side Part
16 pcs. (+1 extra)
Wood Screw
for Caster
16 pcs. (+1 extra)
Cam Lock
6 pcs. (+1 extra)
Cam Lock Screw
6 pcs. (+1 extra)
H.
Back Panel
4 pcs.
I.
Front Piece
1 pc.
J.
Front Piece
1 pc.
Tools Required For Assembly : Phillips screwdriver
Home Styles Consumer Assistance Line 888-680-7460 and 877-831-0319
[email protected]

Assembly Instructions 2/5
STEP 1
IMPORTANT
Do not tighten up all the screws until each part is properly assembled.
You should keep Hex Wrench in a safe place as you may need to
tighten up the Head Cap Bolts in the future.
L
Attach the two locking Casters
to the front of the Base (L).
Attach the two non-locking
casters to the back of the
Base (L). (See figure 1)
(Note : The ‘Arrow’ sticker
indicates the front of the base.)
Head Cap Bolt
Wood Screw
Wood Screw
Locking Caster
(Figure 1)
B
H
H
H
H
F
E
EJ
G
G
I
STEP 2
Attach Back Stretcher (E) to Side Panel (B) at the lower position with Head Cap Bolt.
Attach Back Pieces (F) and (G) to the Back Stretcher (E), then slide Back Panels (H) in place.
Attach Back Stretcher (E) to the unit at upper position.
Tighten the Head Cap Bolt.
Attach Front Pieces (I) and (J) to the unit with Head Cap Bolts.
Lower Position
Upper Position
Tighten Head
Cap Bolt by
Hex Wrench.

Instructions 3/5
STEP 3
STEP 4
Attach Divider (K) in between Front Pieces
(I) and (J).
Attach Middle Panel (C) to Back Piece (F).
Attach Side Panel (D) to the unit with Head Cap Bolts.
Attach Base (L) from Step 1
to the unit, using Cross Dowels
and Head Cap Bolts (long).
Cross Dowel
Head Cap Bolt
Head Cap Bolt (long)
F
C
D
L
I
J
K

Put Cam Lock Screws into the
pre-drilled holes in Top (A).
STEP 5
STEP 6
Assembly Instructions 4/5
Cam Lock Screw
Cam Lock
Head Cap Bolt
Head Cap Bolt
(long)
Cross Dowel
A
A
K
M
M
N
N
Adjustable Pin
Insert Adjustable Pins into
the side panels and middle
panel at the desired level.
Place Shelves (N) into position.
Attach Side Bar (M) to the unit
with Head Cap Bolts.
Insert the Cross Dowel into
the hole of Divider (K) and
tighten Head Cap Bolt (long)
from the back of unit.
Place Top (A) onto the unit,
using Cam Locks.
Figure 2
Figure 1
STEP 7
Attach Pull Handles to the
Doors (O) and (P) using Machine
Screws. (See figure 1)
Attach the Doors (O) and (P) to
the side panels and middle panel
slide the door lift hinges into the
side panel and middle panel
lift hinges. (See figure 2)
Slide the Drawers (Q) into place.
Cover up all holes with
Wood Plug. (See figure 3) Figure 3
O
O
P
QQ
P

Assembly Instructions 5/5
(Figure 1)
(Figure 2)
MAKE SURE ROLLER
IS ON THE BACK
Q2
Q2
Q2
Q3
Q3
Q3
Q4
Q4
Q4
Q5
Q5
Q1
Q1
Q1
Drawer
Part List
Q1.
Front Part
2 pcs.
Q5.
Base Part
2 pcs.
Q2.
Back Part
2 pcs.
Q3.
Side Part
2 pcs.
Q4.
Side Part
2 pcs.
* If you are missing any
of these parts, please
contact our DMI
Customer Service
Department at
1-877-831-0319 or fax
us at 1-800-755-2878.
(Figure 3)
(Figure 4)
Attach Q1 to Q3 and Q4, using
a Phillips screwdriver and
the long wood screws (4X),
tighten halfway.
Attach Q2 to Q3 and Q4 using
the long wood screws (4X),
tighten halfway. (See figure 1)
Insert the short wood screws (6X)
into the pre-drilled holes in Q5,
tighten screws. (See figure 3)
Tighten all screws used in
drawer assembly.
Attach hardware pulls with
machine screws.
(See figure 4)
Slide Q5 into the grooves in Q3
and Q4. Be sure to push the
Q5 all the way forward so
it meets the Q1. (See figure 2)
STEP 1
STEP 2
STEP 3
STEP 4