Home Styles 20 05050 0077 User manual

Home Styles Customer Service: www.homestyles-furniture.com,
[email protected], 888-680-7460, 877-831-0319
Tool(s) required for assembly: Phillips screwdriver, Level, Drill (8 volts or less), 3/8” Drill Bit
Part List
IMPORTANT
Carefully remove all the parts from the carton and
place them individually on a soft cloth to prevent
scratches or other damage.
Carefully and strictly follow these assembly instructions
to ensure a completed product as designed.
Do not use power tools above 8 volts to assemble.
Bracket
2 pcs.
20 05050 0077
Closet Wall Hanging Unit
A.
Back Frame
1 pc.
F.
Back Frame
1 pc.
B.
Side
1 pc.
G.
Side
1 pc.
C.
Side
1 pc.
H.
Side
1 pc.
D.
Rail
3 pcs.
E.
Hanger
2 pcs.
J.
Shelf
1 pc.
I.
Shelf
1 pc.
K.
Base
1 pc.
Hardware List
Hex Wrench
1 pc.
M6x16
Head Cap Bolt
32 pcs. (+1 extra)
M6x13
Tapered Bolt (short)
8 pcs. (+1 extra)
Flat Washer (large)
18 pcs. (+1 extra)
Small Hex Wrench
1 pc.
Spring Washer
32 pcs. (+1 extra)
M6x32
Tapered Bolt
2 pcs. (+1 extra)
M6x44
Tapered Bolt (long)
8 pcs. (+1 extra)
M3x15
Wood Screw
8 pcs. (+1 extra)
Flat Washer
14 pcs. (+1 extra)

Assembly Instructions 2/8
IMPORTANT
Use a soft cloth between these parts and the floor.
Do not use power tools above 8 volts to assemble.
Do not tighten all the bolts until each part is properly assembled.
The unit must be level to work properly. Use the included adjustable levelers to level.
Keep Hex Wrench as the bolts may need to be tightened in the future.
STEP 1
Attach Side (B) to Back Frame (A) with Tapered Bolts (long),
. (See Figure 1)tightening bolts only halfway
Attach Rails (D) to unit with Head Cap Bolts, Spring Washers and Flat Washers,
. (See Figure 2)tightening bolts only halfway
Attach Hangers (E) to unit with Tapered Bolts (short),
. (See Figure 3)tightening bolts only halfway
A
B
D
D
E
Figure 1
Figure 2
Figure 3
Tapered Bolt (short)
Tapered Bolt (long)
Flat Washer
Spring Washer
Head Cap Bolt

Assembly Instructions 3/8
CSTEP 2
Attach Side (C) to unit with
Head Cap Bolts, Spring Washers,
Flat Washers, Tapered Bolts (short)
and Tapered Bolts (long),
.tightening bolts only halfway
Tighten all bolts used in Steps 1 and 2.
Tapered Bolt (short)
Tapered Bolt (long)
Flat Washer
Spring Washer
Head Cap Bolt
Flat Washer (large)
Spring Washer
Head Cap Bolt
STEP 3
Attach Shel (I) and Base (K) to unit withf
Head Cap Bolts, Spring Washers and Flat Washers (large),
. (See Figure 4)tightening bolts only halfway
Tighten all bolts.
I
Figure 4
K

Assembly Instructions 4/8
STEP 4
Attach Side (G) to Back Frame (F)
with Tapered Bolts (long),
.tightening bolts only halfway
Attach Rail (D) to unit with
Head Cap Bolts, Spring Washers
and Flat Washers,
tightening bolts only halfway.
Attach Hanger (E) to unit
with Tapered Bolts (short),
.tightening bolts only halfway
DE
F
G
Tapered Bolt (short)
Tapered Bolt (long)
Flat Washer
Spring Washer
Head Cap Bolt
Flat Washer (large)
Spring Washer
Head Cap Bolt
J
STEP 5
Attach Shelf (J) to unit with
Head Cap Bolts, Spring Washers
and Flat Washers (large),
tightening bolts only halfway.

Assembly Instructions 5/8
Flat Washer (large)
Spring Washer
Head Cap Bolt
Head Cap Bolt
Spring Washer
Flat Washer (large)
STEP 7
Attach unit from Step 3 to unit with
Tapered Bolts, Head Cap Bolts, Spring Washers
and Flat Washers, .tightening bolts only halfway
Tighten all bolts.
Tapered Bolt
Flat Washer
Spring Washer
Head Cap Bolt
Tapered Bolt (long)
Tapered Bolt (short)
STEP 6
Side (H) to unit withAttach
Head Cap Bolts,
Spring Washers,
Flat Washers,
Flat Washers (large),
Tapered Bolts (short)
and Tapered Bolts (long),
tightening bolts only halfway.
Tighten all bolts used in
Steps 4, 5 and 6.
H

Assembly Instructions 6/8
STEP 8
Turn unit to its upright position.
Place unit at desired location.
Note: If assembling multiple Closet Wall Units together place all units
at desired location.
Level unit(s) by adjusting the adjustable levelers on bottom of unit(s).
(See Figure 5) Figure 5

Assembly Instructions 7/8
Hardware List
STEP 9
Drill a 3/8” hole in wall in-line with
pre-drilled hole at top of unit.
Move unit.
Insert Anchor into the wall hole
and attach Bracket with Wall Screw.
Attach Bracket at pre-drilled hole
at back of unit with Machine Screw.
Move unit back into place.
If assembling multiple Closet Wall Units
together, go to and complete Step 10 now,
then return to and complete Step 9.
Slide Tipover Restraint through
Bracket on wall and Bracket on unit.
(See Figure 6)
Put tie end of Tipover Restraint into lock
end of Tipover Restraint and pull until tight.
Anchor
1 pc. (+1 extra)
Bracket
2 pcs. (+1 extra)
Tipover Restraint
1 pc. (+1 extra)
M3.5x40
Wall Screw
1 pc. (+1 extra)
M4x10
Machine Screw
1 pc. (+1 extra)
Figure 6
Machine Screw
Wall Screw
Bracket
on wall
Anchor in wall
3/8” wall hole
Pre-drilled hole
at top of unit
Tie end
Lock end
Bracket at
top of unit
Tipover
Restraint
Drill 3/8” hole in wall
Back of unit
IMPORTANT
To help reduce the risk of the unit tipping over, the Tipover Restraint must be installed following these instructions exactly.

Assembly Instructions 8/8
STEP 10
Note: If assembling multiple Closet Wall Units together, complete Step 10.
Attach tops of units together with Brackets and Wood Screws into pre-drilled holes.
(See Figure 7)
Return to and complete Step 9.
Figure 7
Wood Screw
Bracket

NEVER
use glass cleaners on
finished furniture. Ammonia
chemically attacks the finish.
allow liquids to remain on furniture.
Absorption causes parts to warp
and split and finishes to delaminate.
NEVER
CARE INSTRUCTIONS
Do not use rubber
based placemats.
PREVENT
DISCOLORING
Do not use commercial
waxes and polishes.
PREVENT
YELLOWING
Do not place hot
objects on surface.
PREVENT
FINISH DAMAGE
Do not write
directly on surface.
PREVENT
MARKING
Do not use power tools
above 8 volts to assemble.
PREVENT
CRACKING
Do not place
in direct sunlight.
PREVENT
FADING
with a soft cloth moistened
in lukewarm soap and water.
Buff with a dry clean cloth.
CLEAN
Home Styles will provide replacements free of charge for missing or damaged hardware or parts within 30 days of
purchase. Digital images of the defective parts may be required. If the product was not purchased from an authorized
retail affiliate, Home Styles is under no obligation to provide replacement parts. Parts are not available for fully assembled
items nor are parts available for sale. Replacements for missing or damaged hardware or parts may be requested at:
www.homestyles-furniture.com/customer-service/replacement-parts
Home Styles Customer Service: www.homestyles-furniture.com,
[email protected], 888-680-7460, 877-831-0319