Home Styles 5180-64 User manual

IMPORTANT
Carefully remove all the parts from the carton and
place them individually on a soft cloth to prevent
scratches or other damage.
Carefully and strictly follow these assembly instructions
to ensure a completed product as designed.
Do not use power tools above 8 volts to assemble.
5180-64
Pantry
styles Customer Service: www.homestylesfurniture.com,home
[email protected], 888-680-7460
Hex Wrench
1 pc.
Small Hex Wrench
1 pc.
Cam Lock Screw
28 pcs. (+1 extra)
Flat Washer
4 pcs. (+1 extra) Handle
4 pcs.
M4x15
Machine Screw
8 pcs.
Adjustable Pin
16 pcs. (+1 extra)
M3.5x16
Wood Screw
16 pcs. (+1 extra)
Cam Lock
28 pcs. (+4 extra)
Spring Washer
4 pcs. (+1 extra)
M6x35
Head Cap Bolt
4 pcs. (+1 extra)
S.
Door
1 pc.
D.
Base
1 pc.
N.
Top
1 pc.
Q.
Side Panel
1 pc.
U.
Back Upright
1 pc.
T.
Back Panel
2 pcs.
O.
Front Rail
1 pc.
M.
Back Rail
4 pcs.
P.
Side Panel
1 pc.
K.
Leg
2 pcs.
C.
Shelf
4 pcs.
A.
Middle Panel
1 pc.
B.
Front Rail
1 pc.
R.
Door
1 pc.
H.
Door
1 pc.
E.
Side Panel
1 pc.
F.
Side Panel
1 pc.
G.
Door
1 pc.
I.
Back Panel
2 pcs.
J.
Back Upright
1 pc.
Part List
Hardware List
Tool(s) required for assembly: Phillips screwdriver, Level, Drill (8 volts or less), 3/8” Drill Bit

Assembly Instructions 2/8
STEP 1
Insert Cam Lock Screws into pre-drilled holes in Middle Panel (A),
Bottom (D), Top (N) and Side Panels (E), (F), (P), (Q), then tighten.
(See Figure 1)
D
E F
N
PQ
Cam Lock Screw
IMPORTANT
Use a soft cloth between these parts and the floor.
Do not use power tools above 8 volts to assemble.
Do not tighten all the bolts until each part is properly assembled.
The unit must be level to work properly. Use the included adjustable levelers to level.
Keep Hex Wrench as the bolts may need to be tightened in the future.
A
Figure 1

Assembly Instructions 3/8
STEP 2
Attach Back Rail (M) to
Side Panel (F) with Cam Lock.
(See Figure 2)
Attach Back Upright (J) to
Back Rail (M).
Slide Back Panels (I) into position.
Attach Back Rail (M) to unit
with Cam Lock.
STEP 3
Attach Front Rail (B)
to unit with Cam Lock.
Attach Side Panel (E)
to unit with Cam Locks.
Figure 2
B
E
F
M
I
I
M
Cam Lock
Cam Lock
J

Assembly Instructions 4/8
STEP 5
Turn unit over to its upright position.
Attach Middle Panel (A) to unit with
Cam Locks.
STEP 4
Attach Base (D) to unit
with Cam Locks.
Attach Legs (K) to unit with
Flat Washers, Spring Washers
and Head Cap Bolts.
(See Figure )3
K
K
D
Cam Lock
Head Cap Bolt
Spring Washer
Flat Washer
A
Cam Lock
Figure 3

O
P
Q
M
T
T
M
Assembly Instructions 5/8
STEP 6
Attach Back Rail (M) to
Side Panel (Q) with Cam Lock.
Attach Back Upright (U) to
Back Rail (M).
Slide Back Panels (T) into position.
Attach Back Rail (M) to unit
with Cam Lock.
STEP 7
Attach Front Rail (O)
to unit with Cam Lock.
Attach Side Panel (P)
to unit with Cam Locks.
Cam Lock
Cam Lock
U

Assembly Instructions 6/8
STEP 8
Turn unit over to its upright position.
Attach Top (N) to unit with Cam Locks.
STEP 9
Attach unit from Step 8 to unit from Step 5
with Cam Locks.
Cam Lock
NCam Lock

Assembly Instructions 7/8
STEP 10
Insert Adjustable Pins into side panels
at desired level.
Place Shelves (C) into position.
Attach Doors (G), (H), (R) and (S) to unit
by sliding door hinges into
side panel hinges. (See Figure )4
Attach Handles to Doors (G), (H), (R)
and (S) with Machine Screws.
(See Figure )5
STEP 11
Level unit by adjusting the adjustable
levelers on bottom of unit. (See Figure )6
Insert Wood Screws into pre-drilled holes
in unit, then tighten.
Note: Unit must be level
before tightening
these screws.
Wood Screw
Machine Screw
Handle
Adjustable Pin
C
H
S
C
C
C
R
G
Figure 5Figure 4
Figure 6

Assembly Instructions /88
STEP 12
Place unit at desired location.
Drill a 3/8” hole in wall in-line with
Pre-drilled hole at top of unit.
Move unit.
Insert Anchor into the wall hole
and attach Bracket with Wall Screw.
Attach Bracket at pre-drilled hole
at top of unit with Wood Screw.
Move unit back into place.
Slide Tipover Restraint through
Bracket on wall and Bracket on unit.
(See Figure )7
Put tie end of Tipover Restraint into lock
end of Tipover Restraint and pull until tight.
Figure 7
IMPORTANT
To help reduce the risk of the unit tipping over, the Tipover Restraint must be installed following these instructions exactly.
Anchor
1 pc. (+1 extra)
Bracket
2 pcs. (+1 extra)
Tipover Restraint
1 pc. (+1 extra)
M3.5x40
Wall Screw
1 pc. (+1 extra)
M3.5x16
Wood Screw
1 pc. (+1 extra)
Wood Screw
Wall Screw
Bracket
on wall
Anchor in wall
3/8” wall hole
Pre-drilled hole
at top of unit
Tie end
Lock end
Bracket at
top of unit
Drill 3/8” hole in wall
Top of unit
Hardware List
Tipover
Restraint

NEVER
use glass cleaners on
finished furniture. Ammonia
chemically attacks the finish.
allow liquids to remain on furniture.
Absorption causes parts to warp
and split and finishes to delaminate.
NEVER
CARE INSTRUCTIONS
Do not use rubber
based placemats.
PREVENT
DISCOLORING
Do not use commercial
waxes and polishes.
PREVENT
YELLOWING
Do not place hot
objects on surface.
PREVENT
FINISH DAMAGE
Do not write
directly on surface.
PREVENT
MARKING
Do not use power tools
above 8 volts to assemble.
PREVENT
CRACKING
Do not place
in direct sunlight.
PREVENT
FADING
with a soft cloth moistened
in lukewarm soap and water.
Buff with a dry clean cloth.
CLEAN
homestyles will provide replacements free of charge for missing or damaged parts within 30 days of purchase.
Digital images of the defective parts may be required. If the product was not purchased from an authorized retailer,
homestyles is under no obligation to provide replacement parts. Parts are not available for fully assembled items nor
are parts available for sale. Replacements for missing or damaged parts may be requested via contact info below.
styles Customer Service: www.homestylesfurniture.com,home
[email protected], 888-680-7460