Home Styles 20 08000 0611 User manual

Buffet
20 08000 0611
D.
Plinth
2 pcs.
Hardware List
Part List
Home Styles Customer Service: www.homestyles-furniture.com,
[e-mail], 888-680-7460, 877-831-0319
Tool(s) required for assembly: Phillips screwdriver, Level, Drill (8 volts or less), 3/8” Drill Bit
Carton 20 08000 0612 is also needed for assembly.
IMPORTANT
Carefully remove all the parts from the carton and
place them individually on a soft cloth to prevent
scratches or other damage.
Carefully and strictly follow these assembly instructions
to ensure a completed product as designed.
Do not use power tools above 8 volts to assemble.
A.
Top
1 pc.
B.
Base
1 pc.
C.
Plinth
2 pcs.
E.
Shelf
4 pcs.
N.
Drawer
3 pcs.
Refer to later page(s) of these
instructions for drawer assembly.
Cam Lock Screw
46 pcs. (+1 extra)
Cam Lock
28 pcs. (+4 extra)
Dowel
28 pcs. (+1 extra)
M3.5x64
Wood Screw
14 pcs. (+1 extra)
M3.5x38
Flat Head Screw (long)
14 pcs. (+1 extra)
M3.5x14
Wood Screw for Hinge
36 pcs. (+1 extra)
Adjustable Pin
16 pcs. (+1 extra)
M3.5x25
Flat Head Screw
15 pcs. (+1 extra)
Cover
4 pcs. (+1 extra)
Cam Lock (small)
18 pcs. (+2 extra)
M3x20
Flat Head Screw (short)
16 pcs. (+1 extra)
Plastic Clip
16 pcs. (+1 extra)
Hinge
6 pcs.

IMPORTANT
Use a soft cloth between these parts and the floor.
Do not use power tools above 8 volts to assemble.
Do not tighten all the screws until each part is properly assembled.
The unit must be level to work properly. Use the included adjustable levelers to level.
Assembly Instructions 2/9
STEP 1
Place Top (A), Base (B), Plinths (C) and Middle Panels (H), (I) on a soft cloth.
Insert Cam Lock Screws into pre-drilled holes in Top (A), Base (B),
Plinths (C) and Middle Panels (H), (I), then tighten. (See Figure 1) Figure 1
Cam Lock Screw
A
C
C
HI
B

Assembly Instructions 3/9
STEP 2
Insert Dowels into pre-drilled holes
in Uprights (K). (See Figure 2)
Attach Uprights (K) to
Middle Panels (H) and (I)
with Flat Head Screws (long).
(See Figure 3)
Figure 2 Figure 3
Figure 4
H
I
K
K
Dowel Flat Head Screw (long)
STEP 3
Insert Dowels into
pre-drilled holes in Rails (F).
Attach Side Panels (H) and (I)
to Rails (F) with Cam Locks.
(See Figure 4)
F
F
Cam Lock
Dowel
H
I

STEP 5
Slide Back Panels (L) into position.
Cam Lock
Dowel
STEP 6
Insert Dowels into
pre-drilled holes in unit.
Attach Side Panels (G) and (J)
to unit with Cam Locks.
Cover Cam Locks with Covers.
(See Figure 5)
G
J
Cover
Assembly Instructions 4/9
L
STEP 4
Place Top (A) upside down on a soft cloth.
Insert Dowels into pre-drilled holes in Top (A).
Attach unit to Top (A) with Cam Locks.
Dowel
LL
A
Figure 5

STEP 8
Attach Plinths (C) to Plinths (D) with Cam Locks.
D
C
Assembly Instructions 5/9
STEP 7
Insert Dowels into
pre-drilled holes in unit.
Attach Base (B) to unit
with Cam Locks and
Flat Head Screws (long).
(See Figure 6)
Flat Head Screw (long)
Dowel
B
Figure 6
C
D
Cam Lock
Wood Screw
Dowel
STEP 9
Insert Dowels into pre-drilled holes in unit.
Attach plinth unit to unit with Wood Screws.
Cam Lock

Assembly Instructions 6/9
Figure 7
Wood Screw for Hinge
Hinge
M
M
Figure 8 Figure 9
STEP 11
Turn unit from Step 9 over to its’ upright position.
Attach Doors (M) to unit with Wood Screws for Hinge.
(See Figure 8)
Insert Adjustable Pins into side panels and
middle panels at desired level. (See Figure 9)
Place Shelves (E) into position.
M
M
E
EE
E
Adjustable Pin
Wood Screw for Hinge
STEP 10
Place Doors (M) face down on a soft cloth.
Attach Hinges to Doors (M) with Wood Screws for Hinge
into pre-drilled holes, then tighten.
(See Figure 7)

Part List
Assembly Instructions 7/9
N1.
Drawer Front
3 pcs.
N2.
Drawer Back
3 pcs.
N3.
Drawer Side
3 pcs.
N4.
Drawer Side
3 pcs.
N5.
Drawer Bottom
3 pcs.
N6.
Support
3 pcs.
Drawer (N)
STEP 12
Insert Cam Lock Screws into pre-drilled
holes in Drawer Front (N1), then tighten.
Attach Drawer Sides (N3) and (N4)
to Drawer Front (N1) with Cam Locks (small).
Cam Lock Screw
Cam Lock (small)
N4
N1
N3
STEP 13
Slide Drawer Bottom (N5) into groove.
Attach Support (N6) to unit
with Cam Locks (small).
N2
N6
N5
Cam Lock (small)
STEP 14
Attach Drawer Back (N2) to unit with Flat Head Screws.
Flat Head Screw

Assembly Instructions 8/9
STEP 15
Level unit by adjusting the adjustable
levelers on bottom of unit. (See Figure 10)
Note: Unit must be level to proceed.
Slide Drawers (N) into position.
Figure 12 Figure 13
UP Front Back
Down
Figure 14
Left
Right
STEP 17
If needed, adjust doors up or down by removing the front Wood Screws for Hinge and
loosening slightly the back Wood Screws for Hinge from side panel, adjusting doors up
or down and reinstalling screws. (See Figure 12)
If needed, adjust doors left to right. (See Figure 13)
If needed, adjust doors front to back. (See Figure 14)
Figure 10
STEP 16
Attach Plastic Clips to unit
with Flat Head Screws (short).
(See Figure 11)
Note: Unit must be level
before attaching Plastic Clips.
Figure 11
N
N
N
Flat Head Screw (short)
Plastic Clip

Assembly Instructions 9/9
Hardware List
IMPORTANT
To help reduce the risk of the unit tipping over, the Tip-over Restraints must be installed following these instructions exactly.
Anchor
2 pcs. (+1 extra)
Bracket
4 pcs. (+1 extra)
Tip-over Restraint
2 pcs. (+1 extra)
M3.5x38
Wall Screw
2 pcs. (+1 extra)
M3x16
Wood Screw
2 pcs. (+1 extra)
STEP 18
Place unit at desired location.
Drill 3/8” holes in wall in-line with
pre-drilled holes at top of unit.
Move unit.
Insert Anchors into the wall hole
and attach Brackets with Wall Screws.
Attach Brackets at pre-drilled holes
at top of unit with Wood Screws.
Move unit back into place.
Slide Tip-over Restraints through
Brackets on wall and Brackets on unit.
(See Figure 15)
Put tie end of Tip-over Restraints into lock
end of Tip-over Restraints and pull until tight.
Bracket
on wall
Anchor in wall
3/8” wall hole
Tie end
Lock end
Bracket at
top of unit
Tip-over
Restraint
Figure 15
Wood Screw
Wall Screw Pre-drilled hole
at top of unit
Drill 3/8” hole in wall
Top of unit

NEVER
use glass cleaners on
finished furniture. Ammonia
chemically attacks the finish.
allow liquids to remain on furniture.
Absorption causes parts to warp
and split and finishes to delaminate.
NEVER
CARE INSTRUCTIONS
Do not use rubber
based placemats.
PREVENT
DISCOLORING
Do not use commercial
waxes and polishes.
PREVENT
YELLOWING
Do not place hot
objects on surface.
PREVENT
FINISH DAMAGE
Do not write
directly on surface.
PREVENT
MARKING
Do not use power tools
above 8 volts to assemble.
PREVENT
CRACKING
Do not place
in direct sunlight.
PREVENT
FADING
with a soft cloth moistened
in lukewarm soap and water.
Buff with a dry clean cloth.
CLEAN
Home Styles will provide replacements free of charge for missing or damaged hardware or parts within 30 days of
purchase. Digital images of the defective parts may be required. If the product was not purchased from an authorized
retail affiliate, Home Styles is under no obligation to provide replacement parts. Parts are not available for fully assembled
items nor are parts available for sale. Replacements for missing or damaged hardware or parts may be requested at:
www.homestyles-furniture.com/customer-service/replacement-parts
Home Styles Customer Service: www.homestyles-furniture.com,
[e-mail], 888-680-7460, 877-831-0319