Honeywell CL70PE User manual

www.honeywellaircoolers.com
E-mail: [email protected]
Model: CL70PE
Portable Evaporative Air Cooler
User Manual
Read and save these instructions before use
www.honeywellaircoolers.com
Scan Here:

1) Control Panel
2) Handle
3) Louvers
4) Water Level Indicator
5) Casters
6) Ice Compartment Lid
7) Power Cord Wrap
8) Water Tank
9) Power Cord & Plug
10) Plastic Net Filter
11) Rear Grill Screw
12) Honeycomb Cooling Media
13) Rear Grill
14) Water Regulator
15) Water Fill Door
16) Water Inlet Valve
17) Drain Plug
PARTS DESCRIPTION
1
(5)
(1)
(2)
(3)
(10)
(8)
(11)
(12)
(14) (16)
(15)
(13)
(17)
(6)
(7)
(4)
(9)
WARNING -- READ AND SAVE THE AIR COOLER SAFETY & MAINTENANCE GUIDE AND USER
MANUAL BEFORE USING THIS PRODUCT. FAILURE TO FOLLOW THESE INSTRUCTIONS MAY
DAMAGE AND/ OR IMPAIR ITS OPERATION AND VOID THE WARRANTY.
USE & OPERATION
CONTROL PANEL
FUNCTION BUTTONS
POWER
Press the POWER button to turn the unit on. The cooler will start automatically at medium speed. After a
few seconds the speed will switch to low. To turn the unit off, press the button again.
MODE
Press the MODE button to activate evaporative cooling and/or louver swing modes.
Press the MODE button until the “S” indicator light is illuminated on the control panel.
The Vertical Louvers will begin to move left to right automatically.
Press the MODE button until the “C” indicator light is illuminated to activate evaporative
cooling. The water pump will operate and you will feel the cooler air after the Honeycomb
Cooling Media is completely wet.
H M L 0.5 124S C
MODE SPEED POWER TIMER SWING(H)
SWING(V)
Icons on Display Screen
Power
Timer
Swing
(Horizontal Louvers)
Swing
(Vertical Louvers)
Cool
Speed
LOUVER
MOVEMENT

Pressing the MODE button until both “S” and “C” are illuminated will activate both Swing (Vertical
Louvers) and Cool modes simultaneously.
Note: When the “C” mode is not selected, the unit functions in a fan only mode, without evaporative
cooling.
SPEED
Press the SPEED button repeatedly to change the speed between High - Medium - Low.
The indicator light will show the selected speed:
TIMER
Press the TIMER button until the desired time duration setting is selected. When the set time has
passed, the unit will automatically turn off (unit remains in Standby mode until power cord is unplugged
from electrical socket). The TIMER function allows you to program the unit for up to 7.5 hours of use.
SWING(H)
Press the SWING (H) button until the indicator light turns on. This activates the
Horizontal Louvers and they will begin to move up and down automatically.
USE & OPERATION (CONTINUED)
FUNCTION BUTTONS (CONTINUED)
2
The remote control requires AAA (2 x 1.5V) batteries for replacement.
Open the battery compartment at the back of the remote control and insert the batteries inside. Care
must be taken to insert the batteries according to the correct polarity (+ / –) markings shown inside
the battery compartment.
Always point the remote control signal transmitter towards the unit when operating. Make sure that
the signal path is not obstructed.
Remove the batteries if the unit is not going to be used for an extended period of time.
Do not drop the remote control.
REMOTE CONTROL
ROOM COOLING AND HUMIDIFYING
: ON / OFF
: Controls the motion of the horizontal louvers
: Controls the Timer function for automatic off
: Controls the motion of the vertical louvers and
evaporative Cooling On / Off
: Low / Medium / High
•
•
•
•
•
Note:
POWER
SWING
TIMER
MODE
SPEED
Water Regulator
MIN
MAX
In cooling mode, Honeywell Air Coolers provide cool, moist air through the
evaporation of water. There is a manual Water Regulator knob located
behind the ice compartment of the unit. This allows you to adjust the
amount of water pumped over the Honeycomb Cooling Media, thus helping
to control cooling and humidification levels.
When the Water Regulator is set to MIN, the water pump distributes a
minimal amount of water to the Honeycomb Cooling Media. This results in
less water evaporation and reduces the cooling effect.
When the Water Regulator is set to MAX, the water pump distributes the maximum amount of water to
the Honeycomb Cooling Media. This results in maximum water evaporation and greater cooling
performance.
High (H) Medium (M) Low (L)
LOUVER
MOVEMENT
SWING (H)
SPEED
TIMER MODE
Evaporative Air Cooler
ON/OFF

USE & OPERATION (CONTINUED)
3
FILLING WITH WATER
COOLER LOCATION
Make sure to position the air cooler correctly before you set up and start using the product. Please refer
to the COOLER LOCATION section of the separate Safety & Maintenance Guide.
Do not mix different types of batteries such as alkaline, carbon-zinc, or rechargeable batteries.
Do not mix old and new batteries.
Exhausted batteries are to be removed from the product.
•
•
•
REMOTE CONTROL (CONTINUED)
CAUTION:
Unplug the unit from the electrical power outlet before filling or emptying the water tank
Continuous Water Supply Connection:
Locate the male connector at one end of the garden hose. Insert the
garden hose connector into the water inlet valve of the cooler. Screw
and tighten the water inlet valve onto the threaded part of the garden
hose connector, making sure the hose connector is secured to
ensure there will be no leaks. If there is leakage, the hose and the
water inlet valve may not be connected properly. Try to disconnect,
replace and tighten the water inlet valve again.
When the connection is secured, turn ON the water supply and the
water will flow into the water tank of the cooler.
The cooler is now set so the water refills automatically when the
water tank is empty, or when the water reaches below a minimum
level.
When the water tank is full, the water inlet valve will automatically
stop the water supply from overflowing.
WARNING: The maximum water inlet pressure is 0.5 MPa.
•
•
•
•
For a continuous water supply, you will need a garden hose that is
connected to a main water supply
Manual Water Tank Refill:
Open the Water Fill Door located on the side of the unit.
The Water Level Indicator is located at the front of the unit. Refill the
water tank when water level is low. To avoid water spillage and water
droplets at the louvers, do not fill water above the “MAX” indicator level.
Check the water level in the tank before running the COOL function.
Make sure that the water in the tank is above the minimum water level
mark. Running the unit in COOL mode with inadequate water may
cause pump failure.
Note: If ice is available, you may add ice in the ice tray to enhance the
cooling performance.
Water
inlet valve
Garden Hose
Water Fill Door
Ice Tray

USE & OPERATION (CONTINUED)
4
CLEANING & DRAINING THE WATER TANK
If the cooler will not be used for a long period of time, please refer to the STORAGE & MAINTENANCE
GUIDELINES located in the separate Safety & Maintenance Guide.
Move the unit to a location where the water can be drained. Remove the cap from the Drain plug
located at the bottom of the unit. Allow the tank to empty.
Refill the water tank with clean water, up to the maximum level and drain it completely.
Use a damp cloth to remove the dirt and dust from the surface of the unit. Never use corrosive
elements or chemicals to clean this product.
When the product is not in use, store the unit in a dry place our of direct sunlight.
•
•
•
•
WARNING:
Before cleaning the unit, switch the unit OFF and disconnect from the electrical socket.
CLEANING THE PLASTIC NET FILTER* AND HONEYCOMB COOLING MEDIA
The appliance is supplied with a Plastic Net Filter* and
Honeycomb Cooling Media.
The Plastic Net Filter* and Honeycomb Cooling Media
are located inside the Rear Grill. See Figure 1 for
instructions on how to remove them from the unit for
cleaning and maintenance.
Do not run the unit in COOL mode with stale water in
the tank. You must empty the water tank and refill with
fresh water, especially if the tank has not been cleaned
in a long time.
The cleaning frequency for the Honeycomb media
depends on local air and water conditions. In areas
where the mineral content of water is high, mineral
deposits may build up on the Honeycomb Cooling
Media and restrict air flow. Draining the water tank and
refilling with fresh water at least once a week will help
reduce mineral deposits. If mineral deposits remain on
the Honeycomb Cooling Media, the media should be
removed and washed under fresh water. The media
should be cleaned every two months or sooner,
depending on your needs.
For best results allow the Honeycomb Cooling Media to
dry after each use by turning off the cool function 15
minutes before turning the unit off.
•
•
•
•
•
Honeycomb
Cooling Media
Rear Grill
Horizontal Bar
Figure 1:
Slide out the Plastic Net Filter* and clean with water.
Remove all the screws from the Rear Grill of the Air Cooler.
Carefully pull out the rear grill from the cooler.
Carefully pull out the Honeycomb Cooling Media from the rear
grill.
There are two Horizontal Bars holding the Honeycomb Cooling
Media in place. Remove all the screws from the Horizontal Bars
and then pull the bars off of the Honeycomb Cooling Media.
Replace or clean media with water and a damp cloth as
needed.
WARNING: DO NOT operate the Air Cooler when the
Rear Grill or Honeycomb Media is removed from the Air Cooler,
or if there is a loose-fitting Rear Grill or Honeycomb Cooling
Media. Doing so can cause serious injury or dangerous
electrical shock.
1.
2.
3.
4.
5.
6.
Removing the Plastic Net Filter*/ Honeycomb Cooling Media:
*Applicable for models with Plastic Net Filter only.
Screws
Screws
Plastic
Net
Filter

TECHNICAL SPECIFICATIONS
Voltage
Frequency
Wattage
Cooling Media
Product Dimension
Net Weight
Water Tank Capacity
ELECTRICAL WIRING DIAGRAM
CL70PE
220 ~ 240V
50Hz
Honeycomb
706 (W) x 426 (D) x 1008 (H) mm
27.8 (W) x 16.8 (D) x 39.7 (H) in
17.8 kg / 39.2 lbs
330 W
70 Liters / 18.5 Gallons
Version: 220~240V/50Hz
Model
Capacitor
Transformer
COOL
PUMP
COOL
PLUG
H M
M
PCB1
PCB2
M
~
M
L
L
HOR
N
OSC
SWING

AirTek International Corporation Limited.
(JMATEK International Group of Companies)
Manulife Financial Centre, Kwun Tong, Hong Kong
Phone: [phone]
Email: [email protected]
Web: www.honeywellaircoolers.com
Made in China
© 2015 AirTek Int’l Corp. Ltd. All rights reserved.
The Honeywell Trademark is used under license from
Honeywell International Inc.
Honeywell International Inc. makes no representations
or warranties with respect to this product.
This product is manufactured by Airtek Int’l Corp. Ltd.
Distributor:
KHIND ALLIANCES SDN. BHD. (811092-W)
No. 2, Jalan Astaka U8/82, Bukit Jelutong
40150 Shah Alam, Selangor, Malaysia.
Service Center: 1 800 88 0032
Email: [email protected]
Website: http://www.khindalliances.com