Honeywell MORLEY IAS DX Series User manual

Document No. 996-148-000-5, Issue 05
DX user
manual

Dimension Series MORLEY-IAS
User Manual Document No.996-148-000-5, Revision: 5 Page i
Table of Contents
1INTRODUCTION..........................................................................................................................1
1.1 NOTICE ...................................................................................................................................1
1.2 MODELS..................................................................................................................................1
1.3 WARNINGS AND CAUTIONS.......................................................................................................3
1.4 NATIONAL APPROVALS.............................................................................................................3
1.5 EN54 INFORMATION ................................................................................................................4
2USER CONTROL LEVELS..........................................................................................................5
2.1 LEVEL DEFINITION ...................................................................................................................5
2.2 USER PASSWORDS..................................................................................................................5
3CONTROLS AND INDICATIONS................................................................................................6
3.1 CONTROL KEYS.......................................................................................................................6
3.2 FRONT PANEL LED INDICATIONS..............................................................................................8
3.3 ALPHANUMERIC DISPLAY INDICATIONS......................................................................................9
3.3.1 Normal Condition ...........................................................................................................9
3.3.2 Other Conditions ...........................................................................................................................9
3.3.2.1 Loop Device Faults/ Fires ...........................................................................................................9
3.3.2.2 F1 Short-cut Navigation Key ......................................................................................................9
3.3.2.3 Panel Status Summary .............................................................................................................10
3.3.3 Level 2 Menu Displays .................................................................................................................10
4LEVEL 1 DISPLAY FUNCTIONS ..............................................................................................11
4.1 NORMAL CONDITIONS ............................................................................................................11
4.2 OTHER CONDITIONS –ZONAL (DEFAULT)DISPLAY OPTION .......................................................11
4.2.1 Fire Alarm Conditions ..................................................................................................12
4.2.1.1 Panel Fire Alarms..................................................................................................................12
4.2.1.2 Zone Fire Alarms...................................................................................................................12
4.2.1.3 Override Delays ....................................................................................................................13
4.2.2 Fault Conditions ...........................................................................................................13
4.2.2.1 Panel Faults ..........................................................................................................................13
4.2.2.2 Zone Faults ...........................................................................................................................13
4.2.3 Test Conditions ............................................................................................................14
4.2.4 Disablement Conditions...............................................................................................15
4.2.4.1 Panel Disablements ..............................................................................................................15
4.2.4.2 Zone Disablements ...............................................................................................................15
4.3 OTHER CONDITIONS –BY EVENT DISPLAY OPTION ...................................................................16
4.3.1 Fire Alarm Conditions ..................................................................................................16
4.3.1.1 Zone Fire Alarms...................................................................................................................17
4.3.1.2 Panel Fire Alarms..................................................................................................................17
4.3.1.3 Override Delays ....................................................................................................................17
4.3.2 Fault Conditions, Disablement Conditions and Test Conditions .................................17
4.3.2.1 Panel Faults ..........................................................................................................................17
4.3.2.2 Zone Faults ...........................................................................................................................18
4.3.2.3 Test Conditions .....................................................................................................................18
4.3.2.4 Disablement Conditions ........................................................................................................18
4.3.2.4.1 Panel Disablements ........................................................................................................19
4.3.2.4.2 Zone Disablements .........................................................................................................19
4.3.2.4.3 Point disablements..........................................................................................................19
4.4 POWER SUPPLY FAULT CONDITIONS ......................................................................................19
4.5 LIST OF DEVICE ABBREVIATIONS ............................................................................................20
5LEVEL 2 DISPLAY / CONTROL FUNCTIONS .........................................................................21
5.1 DISPLAY FUNCTIONS .............................................................................................................21
5.2 CONTROL FUNCTIONS............................................................................................................21
5.2.1 Sound Alarms / Evacuate ............................................................................................21
5.2.2 Silence / Resound Alarms ...........................................................................................21
5.2.3 Accept / Delayed Day Mode Alarms ............................................................................21

MORLEY-IAS Dimension Series
Page ii Document No. 996-148-000-5, Revision: 5 User Manual
5.2.4 Reset...........................................................................................................................21
5.3 LEVEL 2MENU FUNCTIONS ................................................................................................... 22
5.3.1 Test ............................................................................................................................. 23
5.3.1.1 LED Test ...............................................................................................................................23
5.3.1.2 LCD Test ...............................................................................................................................23
5.3.1.3 Zones Test ............................................................................................................................23
5.3.1.3.1 Introduction .....................................................................................................................23
5.3.1.3.2 Configuring / Stopping Individual Zone Tests.................................................................. 24
5.3.1.3.3 Stopping ALL Zone Tests................................................................................................ 24
5.3.1.4 Output Test ...........................................................................................................................24
5.3.1.4.1 Internal Outputs...............................................................................................................25
5.3.1.4.2 Loop (SLC) Outputs ........................................................................................................25
5.3.1.5 Audible Indicator (Buzzer) Test ............................................................................................. 26
5.3.2 Clock ...........................................................................................................................26
5.3.3 Change the Time ........................................................................................................ 26
5.3.4 Change the Date......................................................................................................... 26
5.3.5 Disable / Enable Functions ......................................................................................... 27
5.3.5.1 Disable / Enable Full Zones ..................................................................................................27
5.3.5.2 Disable / Enable Individual Devices / Points .........................................................................28
5.3.5.3 Disable / Enable Groups .......................................................................................................28
5.3.5.4 Disable / Enable Specific Output Circuits.............................................................................. 28
5.3.5.5 Disable / Enable Detection Mode ..........................................................................................30
5.3.5.6 Disable / Enable Output (Pattern) Delays..............................................................................30
5.3.5.7 Disable / Enable Local Inputs................................................................................................31
5.3.6 View Mode .................................................................................................................. 31
5.3.6.1 View Devices.........................................................................................................................32
5.3.6.1.1 System Sensor / Morley-IAS Device Information ............................................................32
5.3.6.1.2 Apollo Device Information ...............................................................................................33
5.3.6.1.3 Hochiki Device Information .............................................................................................33
5.3.6.2 View The Event Log ..............................................................................................................34
5.3.6.3 View Faults............................................................................................................................34
5.3.6.4 View Disablements................................................................................................................34
5.3.6.5 View Service Information.......................................................................................................35
5.3.6.6 View the Alarm Counter ........................................................................................................35
5.3.6.7 View Voltages .......................................................................................................................36
5.3.6.8 View Version .........................................................................................................................36
6DELAYED DAY MODE OPERATION ...................................................................................... 37
6.1 STAGE 1 .............................................................................................................................. 37
6.2 STAGE 2 .............................................................................................................................. 38
7KEY-SWITCH AND FUNCTION KEY OPERATION ................................................................ 39
7.1 KEY-SWITCH ........................................................................................................................ 39
7.2 FUNCTION KEYS ................................................................................................................... 39
8PRINTER OPERATION ............................................................................................................ 40
8.1 PRINTOUT SAMPLES ............................................................................................................. 40
8.2 CHANGING THE PAPER ROLL.................................................................................................. 40
9LEVEL 3 PROGRAMMER FUNCTIONS .................................................................................. 41
10 MAINTENANCE / INSPECTION............................................................................................... 41
10.1 INSPECTION /TESTING .......................................................................................................... 41
10.1.1 Daily Attention............................................................................................................. 41
10.1.2 Weekly Attention ......................................................................................................... 41
10.1.3 Monthly Attention ........................................................................................................ 41
10.2 LOG BOOK EXAMPLES .......................................................................................................... 42
Table of Figures
FIGURE 1–TYPICAL CONTROLS AND INDICATIONS.................................................................................. 6
FIGURE 2–CHANGING THE PAPER ROLL ............................................................................................. 40

Dimension Series MORLEY-IAS
User Manual Document No.996-148-000-5, Revision: 5 Page iii
Table of Tables
TABLE 1–CONTROL KEY FUNCTIONS .....................................................................................................6
TABLE 2-ALPHANUMERIC AND INTERACTIVE CONTROL KEYS...................................................................7
TABLE 3-LED FUNCTIONS ....................................................................................................................8
TABLE 4–DEVICE TYPE ABBREVIATIONS ..............................................................................................20
TABLE 5-USER MENU OPTIONS...........................................................................................................22
TABLE 6–PANEL INTERNAL OUTPUT CIRCUITS .....................................................................................25
TABLE 7–VOLTAGE /ANALOGUE VALUE READINGS ..............................................................................36
TABLE 8-LOGBOOK REFERENCE DATA ................................................................................................42
TABLE 9-LOGBOOK EVENT DATA.........................................................................................................43

MORLEY-IAS Dimension Series
Page iv Document No. 996-148-000-5, Revision: 5 User Manual
This page intentionally blank

Dimension Series MORLEY-IAS
User Manual Document No.996-148-000-5, Revision: 5 Page 1
1 Introduction
1.1 Notice
•The material and instructions covered in this manual have been carefully checked for accuracy and
are presumed to be correct. However, the manufacturer assumes no responsibility for inaccuracies
and reserves the right to modify and revise this document without
notice.
•These instructions cover the use and operation of the Dimension
Series Fire Alarm Control Panels. Refer to the Product Manual (P/N 996-147-000) for details of how to
install, program and maintain the system.
For use with software
version 3.00, or later.
•The DX1, DX2 and DX4 Fire Alarm Control Panels are 1, 2 and 4 loop panels for use with analogue
addressable devices from the following detector manufacturer ranges:
S90
1.2 Models
•The Dimension Series Fire Alarm Control Panels are available in a range of enclosure sizes. A printer
is available as a factory fit option on all models except for the small enclosure. This manual covers the
following models:
Model No. of Loops Enclosure Max. Battery Size No. of Zones
DX1e-20S 1 Small :7Ah 20
DX1e-40M 1 Medium 12Ah 40
DX2e-40M 2 Medium 12Ah 40
DX4e-40L 4 Large 17Ah 40
:= A printer cannot be fitted in this enclosure
Note: A printer may be fitted as a retrofit item

MORLEY-IAS Dimension Series
Page 2 Document No. 996-148-000-5, Revision: 5 User Manual
0
W O R D
7
P Q R S
8
T U V
9
W
X
YZ
4
G H I
5
J K L
6
MNO
12
A B C
3
DEF
F 1
F 2
1 11 21 31 41 51 61 71 81 92 0
1234567891 0
E
N
5
4
2
1
9
9
7
E
N
5
4
4
1
9
9
7
0
WORD
7
PQRS
8
TUV
9
W
X
YZ
4
GHI
5
JKL
6
MNO
1 2
ABC
3
DEF
F1
F2 1
11 21 31 41 51 61 71 81 92 0
2 12 22 32 42 52 62 72 82 93 0
3 13 23 33 43 53 63 73 83 94 0
1234567891 0
E
N
5
4
2
1
9
9
7
E
N
5
4
4
1
9
9
7
DX1e-20S DX1e-40M, DX2e-40M
0
W O R D
7
P Q R S
8
T U V
9
W
X
YZ
4
G H I
5
J K L
6
MNO
12
A B C
3
DEF
F 1
F 2
1 11 21 31 41 51 61 71 81 92 0
2 12 22 32 42 52 62 72 82 93 0
3 13 23 33 43 53 63 73 83 94 0
1234567891 0
E
N
5
4
2
1
9
9
7
E
N
5
4
4
1
9
9
7
Installer Fit Options:
A front panel key-switch, P/N 795-083, can be
installed in all models. This can be used for:
a) Level 2 Access Control
b) Class Change
c) Bomb Alert
Printer: P/N 795-085. The following panels are
compatible: DX1e-40M, DX2e-40M & DX4e-40L.
Note: Requires a control panel cover with printer
slot (P/N 797-073).
Specials: Large Enclosure Only. The following
future typical special options can be installed in
the lower cabinet area.
Examples:
a) Graphical Mimic Display
b) Up to 4 Key-Switches
c) DIN Rail mounted modules
For further information on either of these options,
contact your supplier / maintenance contractor.
DX4e-40L

Dimension Series MORLEY-IAS
User Manual Document No.996-148-000-5, Revision: 5 Page 3
1.3 Warnings and Cautions
These instructions contain procedures to follow in order to avoid injury and damage to
equipment. It is assumed that the user of this manual has been suitably trained and is
familiar with the relevant regulations.
This panel is CE Marked to show that it conforms to the requirements of the following
European Community Directives:
The EMC Directive 2004/108/EEC, by the application of the following EMC Standards:
•EN 61000-6-3: Electromagnetic Compatibility (EMC) Generic emission standard
for Residential, Commercial and Light industrial environments
•EN 50130-4: EMC Product family standard: Immunity requirements for
components of fire, intruder and social alarm systems.
Low Voltage Directive 2006/95/EEC, by the application of the safety standard:
•EN 60950-1: Safety of information technology equipment.
The Construction Products Directive 89/106/EEC, by the application of the following
standards:
•EN 54-2: 1998, (Amd. 1 & 2): Fire detection and fire alarm systems - Control and
indicating equipment.
•EN 54-4: 1998, (Amd. 1 & 2): Fire detection and fire alarm systems - Power supply
equipment.
EN54
!
EN54-2 13.7
Maximum of 512
sensors / manual
call points per
panel.
•The Dimension Series range of panels has many features that, if
used inappropriately, may contravene the requirements of EN54.
Where such a possibility may arise, a suitable warning is given with
brief details of the EN54 requirement and the relevant section to
which it pertains. A typical EN54 non-compliance warning is
illustrated.
1.4 National Approvals
•This equipment must be installed and operated in accordance with these instructions and the
appropriate national, regional and local regulations specific to the country and location of the
installation. Consult with the appropriate Authority Having Jurisdiction (AHJ) for confirmation of the
requirements.
All equipment is to be operated in accordance with the appropriate standards applicable
•This equipment must be installed in accordance with these instructions and the appropriate national,
regional and local wiring regulations. In the UK the wiring must conform to the requirements of
BS7671 (IEE Wiring Regulations – Sixteenth Edition).

MORLEY-IAS Dimension Series
Page 4 Document No. 996-148-000-5, Revision: 5 User Manual
1.5 EN54 Information
EN54
9
•This Fire Alarm Control Panel complies with the requirements of EN54-2/4. In addition
to the basic requirements of EN54, the panel conforms to the following optional
functions.
Option EN54-2 Clause
Indication:
Alarm counter 7.13
Fault signals from points 8.3
Controls:
Delays to outputs 7.11.1
Manual or automatic switching of delays to outputs 7.11.2
Dependency on more than one alarm signal: Type C 7.12.3
Disablement of each address point 9.5
Test condition 10
Outputs:
Outputs to fire alarm device(s) 7.8
EN54
9
•The power supplies for the Dimension Series of panels comply with the following
clauses of EN54-4.
DX1/2/4e Power Supply Functions EN54-4 Clause
Derive power supply from main power source
Derive power supply from a standby battery source
Charge and monitor the standby battery source
Detect & signal power supply faults
5.1
5.2
5.3
5.4
EN54
N/A
•In addition to the functions required by EN54-2, the panel supports a number of
ancillary functions that are not required by EN54. These are outlined below:
Ancillary Function Manual Section
Auxiliary supply output Refer to Product Manual
Peripheral loop output & supported devices Refer to Product Manual
Auxiliary relay outputs Refer to Product Manual
Printer option 8
Class Change Input 7.2
Group Disable 5.3.5.3

Dimension Series MORLEY-IAS
User Manual Document No.996-148-000-5, Revision: 5 Page 5
2 User Control Levels
2.1 Level Definition
•The DX1e, DX2e and DX4e Fire Alarm Control Panels have three user control levels.
•At all three levels, the LED Displays indicate the condition of the installation, the Zone LED Displays
indicate the location of any fire alarm and the alphanumeric display gives more detailed fire alarm,
fault, and test or disablement information.
•At USER LEVEL 1, all the displays are functional but the front panel control keys are inhibited.
•At USER LEVEL 2, all front panel controls are functional and some system operation parameters and
functions can be changed. User Level 2 is reached by entering a password from level 1.
•At USER LEVEL 3, all front panel controls are functional and full system configuration and
programming is possible. User Level 3 is reached by entering a password from either Level 1 or Level
2. User Level 3 is intended for use by the system installer / maintenance contractor.
EN54
9
EN54-2 5.1
Viewing
Suppressed
Information.
•All of the mandatory indications that may not be suppressed during a
fire alarm condition are shown using Light Emitting (LED) Indicators.
Fire Alarms are shown using LED Indicators for each zone.
•It is possible to view all other conditions such as points in fire, faults,
zones in test and disablement conditions using the navigation (arrow)
keys at Level 1.
2.2 User Passwords
•Up to ten USER LEVEL 2 passwords can be programmed into the panel.
•The USER LEVEL 2 passwords can be assigned / changed at Level 3 by the installer / maintenance
contractor. Level 2 passwords do not allow access to Level 3 functions.

MORLEY-IAS Dimension Series
Page 6 Document No. 996-148-000-5, Revision: 5 User Manual
3 Controls and Indications
0
WORD
7
PQRS
8
TUV
9
W
X
YZ
4
GHI
5
JKL
6
MNO
1 2
ABC
3
DEF
F 1
F 2
11 1 2 1 3 14 1 5 16 1 7 18 1 9 2 0
21 2 2 2 3 24 2 5 26 2 7 28 2 9 3 0
31 3 2 3 3 34 3 5 36 3 7 38 3 9 4 0
1 2 3 4 5 6 7 8 9 1 0
E
N
5
4
2
1
9
9
7
E
N
5
4
4
1
9
9
7
Figure 1 – Typical Controls and Indications
•The diagram above shows the controls and indications on the DX2e-40M model (with optional key
switch and printer fitted). This is typical for all models except the DX1e-20S.
3.1 Control Keys
Key Legend Symbol Function
Sound Alarms
Press to Turn on ALL Sounder Outputs (i.e. evacuate
building manually).
Silence /
Resound
Press to Turn off all activated sounders.
Press again to re-activate the sounders.
Mute Buzzer
Press to silence the internal buzzer.
Accept
Press to accept a Stage 1 Investigation Delay Alarm
System Reset
Press to cancel all alarm / fault conditions and reset the
panel.
Table 1 – Control Key Functions
Optional Key switch
System Status LED
Indicators
Navigation Keys
Optional Printer
Control Keys
ZONE FIRE LED
Indicators
Alphanumeric Liquid
Crystal Display
Numeric Keypad
(Program / Interactive
keys)

Dimension Series MORLEY-IAS
User Manual Document No.996-148-000-5, Revision: 5 Page 7
Key Legend Symbol Function
Function Key
F1
Programmable Function Key. Default is used as an event
view short-cut function or alternatively can be assigned to
the following:
Bomb Alert, Class Change, Detection Mode start / stop.
Function Key
F2
Programmable Function Key. May be assigned to the
following:
Bomb Alert, Class Change, Detection Mode start / stop.
Navigation
Keys
Press to select and scroll through Level 1 display functions
for fire, fault, and disablement and test conditions.
Press to select and scroll through menu options. Follow the
on screen prompts.
0 – 9
A – Z, WORD
Numeric keypad for entering numbers. May also be used
during programming to enter letters of the alphabet and
‘words’ for text message entry. This works in a similar
fashion to a mobile telephone keypad.
No
Press to answer No, or cancel a display option and return to
a previous menu.
Yes
Press to answer Yes, to Enter / Select or to Confirm
changes.
Table 2 - Alphanumeric and Interactive Control Keys
•The control keys are disabled at USER LEVEL 1. Pressing a control or number key will cause the
display to prompt for entry of the Level 2 password. The password must be entered to re-enable the
control keys at Level 2.

MORLEY-IAS Dimension Series
Page 8 Document No. 996-148-000-5, Revision: 5 User Manual
3.2 Front Panel LED Indications
Indicator Colour Function How to Clear
Block 1
FIRE Red The panel has detected a fire alarm
condition, or the ‘Sound Alarms’ key
has been pressed.
Correct the condition causing the alarm
and then perform a panel reset.
FAULT Yellow The panel has detected a fault. Correct the condition causing the fault
and then perform a panel reset.
Test Yellow The system is in test mode. The LCD
shows which zones are being tested.
Cancel / Stop test when finished.
Disablement Yellow Part of the system, either input or
output, has been disabled manually
by the user.
Re-enable the device or devices. Refer
to Disablement Function.
Delayed Mode Yellow This indicates that the system is operating
with delays to the sounder outputs and the
delays are active (in force).
The delays may be enabled or disabled.
Refer to Disablement Function.
Alarms Silenced Yellow The sounder outputs have been
silenced.
Correct the alarm condition and then
perform a panel reset. NOTE: Press
SILENCE / RESOUND again to
reactivate the sounders.
NOTE: the sounders will automatically
resound if a new alarm occurs in any
zone, unless this function has been
disabled during panel commissioning.
Buzzer Muted Yellow A fault or alarm has been
acknowledged and the internal
buzzer silenced.
Correct the condition causing alarm or
fault and then perform a manual reset.
NOTE: If an new alarm occurs in any
zone or a fault occurs, the internal
buzzer automatically resounds.
Sounders Disabled Yellow The sounder outputs have been
disabled.
Refer to Disablement Function.
Relays Disabled Yellow The relay outputs have been
disabled.
Refer to Disablement Function.
Fire Routing
Equipment
Red Indicates the output to fire routing
equipment (i.e. Fire Brigade) is
activated. NOT CURRENTLY USED.
Power Green STEADY: Indicates presence of power
(either AC Mains and / or batteries).
Block 2
Function 1 Yellow Function programmed when
commissioned – refer to site notes.
Supply Fault Yellow There is a problem with the power
supply, battery or supply input.
Correct the fault condition and then
perform a panel reset.
System / CPU Fault Yellow The CPU has reset or a system fault
has occurred.
Correct the problem, if appropriate, and
then perform a panel reset.
Sounder Fault Yellow This indicates a wiring fault with one
of the sounder output circuits.
Correct the fault condition and then
perform a panel reset.
Earth Fault Yellow An earth connection fault has
occurred on a cable.
Correct the fault condition and then
perform a panel reset.
Function 2 Yellow Function programmed when
commissioned – refer to site notes.
Block 3
Zone FIRE Red STEADY: The zone is in a fire alarm
condition.
Correct the alarm condition and then
perform a panel reset.
Table 3 - LED Functions

Dimension Series MORLEY-IAS
User Manual Document No.996-148-000-5, Revision: 5 Page 9
•The Level 1 LED Indicators are divided into three blocks as described in Table 3 opposite. The LED
Indicators illuminate as red, yellow or green.
•Block 1 contains LED Indicators showing the state of the fire alarm control panel.
•Block 2 contains LED Indicators showing specific fault conditions. In addition, there are two
programmable indicators.
•Block 3 contains the Zone Fire LED Indicators. There are either 20 or 40 LED Indicators depending on
the model.
3.3 Alphanumeric Display Indications
•The alphanumeric liquid crystal display (LCD) gives 80 characters of information on a 2-line display.
The display is illuminated to assist viewing under dim ambient light conditions.
3.3.1 Normal Condition
•If the panel is in the quiescent condition the display shows the day of the week, date and time (24hour
format) as follows:
Wed 07/05/2003 11.38:59
All devices are inside working limits
3.3.2 Other Conditions
3.3.2.1 Loop Device Faults/ Fires
•The alphanumeric display will automatically update to show zonal information about the latest device
to enter a fault or fire condition.
•
IN FAULT ZONE 1 1/1 X:Summary
< ZONE TEXT >→: Device Details
•Use the right arrow key to view the individual device/point details within the affected zone.
•Use the up/down arrow keys to view different zones in the same condition.
•Use the ‘X’ key to exit the summary display.
3.3.2.2 F1 Short-cut Navigation Key
•Where the F1 function key is not programmed to provide a specific function e.g. Bomb alert, Class
change etc, it will operate as a navigation shortcut key.
•Press the ‘F1’ function key once and the alphanumeric display will show the first active event from the
highest priority category available (fires, faults, disablements).
•Use the up/down arrow keys to navigate through all active events in that category. The events are
listed in a purely chronological order i.e. no zonal or other grouping is applied.

MORLEY-IAS Dimension Series
Page 10 Document No. 996-148-000-5, Revision: 5 User Manual
•Press the ‘F1’ key again to toggle to the next highest priority event category available. Where no
category is available, the display will revert to the original summary/zone display.
•Press ’X’ or any numeric key when viewing the active events and the display will revert to the
summary display.
3.3.2.3 Panel Status Summary
•If the panel is in a fire and/or a fault and/or a test and/or a disablement condition the display shows the
status of the panel as follows:
<FIRES> :1 FAULTS :1 ←R→:Select
DISABLED :0 IN TEST :0 9:Details
•The display shows the number of fire alarms, faults, disablements and zones in test. The above
example shows that there is one fire alarm and one fault condition present.
EN54
9
EN54-2 5.1
Viewing
Suppressed
Information.
•All of the mandatory indications that may not be suppressed during a
fire alarm condition are shown using Light Emitting (LED) Indicators.
Fire Alarms are shown using LED Indicators for each zone.
•It is possible to view all other conditions such as points in fire, faults,
zones in test and disablement conditions using the arrow keys at
Level 1.
•To view the information for a particular condition, use the ÍÏÐÎ keys to select the required
condition (the ‘<’ and ‘>’ brackets move to the selected option and flash) and then press the 9key to
select and view further detail.
3.3.3 Level 2 Menu Displays
•When the Level 2 Menu Displays are selected, the display shows a number of listed options. The
example below shows the main Level 2 Menu options. All other menus are similar.
[U0] 1:Commission 2:Test 3:Clock
4:Disable/Enable 5:View Mode

Dimension Series MORLEY-IAS
User Manual Document No.996-148-000-5, Revision: 5 Page 11
4 Level 1 Display Functions
EN54
9
EN54-2 5.1.1
Display of
functional
conditions.
•At Level 1, the panel operates in a display only mode with the control
keys disabled.
•If fire alarm, fault, test or disablement conditions exist, the LED
Indicators will show these. Detailed information can be viewed on the
alphanumeric display using the navigation keys.
The way the panel displays information at level 1 is configurable for one of two options, ‘zonal’ (EN54-2
compliant) or ‘by event’ (not EN54-2 compliant).
Default level 1 display option – zonal
•In this mode the display shows a summary of the panel status
including the number of zones in fire, fault, test and disablement.
•Manual intervention is required for more detailed point information.
EN54
!
EN54-2 7.3.1
& EN54-2
8.2.1
Indication of
zones in alarm &
faults.
Alternative level 1 display option – by event
•In this mode the display scrolls through detailed point information,
one point at-a-time with no manual intervention required.
•It is important to note that operating the panel in this mode means
that the panel does not comply with the EN54-2 clauses highlighted
opposite.
EN54
9
•In a fire alarm condition, the buzzer will sound continuously. It will
automatically resound (if previously muted) for any new fire alarms.
•In a fault condition, the buzzer will sound intermittently (1-second on /
1-second off). It will automatically resound (if previously muted) for
any new fault condition registered.
EN54-2 7.4 &
EN54-2 8.6
Audible
Indication.
•The internal buzzer can be silenced at Level 1 – press
the MUTE BUZZER key.
4.1 Normal Conditions
•When the system is in a normal condition, the green AC Power LED will be illuminated. The
alphanumeric display will show the time and date and an ‘All systems normal’ status message.
Wed 07/05/2003 11.38:59
All devices are inside working limits
4.2 Other Conditions – zonal (default) display option
•The display shows the status of the panel if any fire, fault, test or disablement conditions occur.
<FIRES> :1 FAULTS :1 ←R→:Select
DISABLED :0 IN TEST :0 9:Details
•Press ‘X’ in any of the following sub menus to return immediately to this display.

MORLEY-IAS Dimension Series
Page 12 Document No. 996-148-000-5, Revision: 5 User Manual
4.2.1 Fire Alarm Conditions
•If the control panel initiates an alarm condition, the FIRE LED Indicators will be illuminated and, if
appropriate, the relevant ZONE FIRE LED Indicators will illuminate. The internal buzzer will sound and
the alphanumeric display will indicate the number of fires.
•To view more detailed information regarding the fire alarm location use the navigation keys as follows.
•Press the ÍÏÐÎ keys to select the FIRES option, then press the 9key and the display shows the
following for example:
TOTAL PANEL FIRES :1 →:Panel Events
TOTAL ZONES IN FIRE :2 ↓:Zone Details
•This display indicates that there are two zones in fire and that a fire alarm has been raised at the
panel. To view these, press the Îkey to view the fire alarm initiated at the panel and press the Ðkey
to view the zones in fire.
4.2.1.1 Panel Fire Alarms
FIRE 01/01 11:22
EVACUATE ←:back R:more
•The above example shows there are one of one fire alarm raised at the panel. This was an “Evacuate”
raised at 11:22AM when the “Sound Alarms” key was pressed.
•If there is more than one fire alarm indicated, use the Ïand Ðkeys to view these (Note: The ‘R:
more’ option is not shown if there is only one event, the ‘↓’ and ‘↑’ keys are shown for the first and last
entries in the list). Press the Íkey to return to the previous display.
4.2.1.2 Zone Fire Alarms
•When selected, the display shows the first zone with a fire alarm condition. For example:
IN FIRE ZONE 3 1/ 2 R:More Zones
<Zone-Location-Text> →:Device Details
•The display shows the Zone number and Zone Location Text (20 character description).
•To view other zones in fire (or to return to the previous display), press the Ïand Ðkeys.
•To view the devices (points) in a fire alarm condition, press the Îkey. The display then shows the
first point in alarm in the selected zone. For example:
FIRE 01/02 Z04 L1 A011 MCP 11:45
<Point-Location-Txt> ←:back R:more
•The display shows the alarm number and the total number of devices (points) in a fire alarm condition in
this zone (01/02), the Zone number (Z04), the loop number to which this device is connected (L1), the
address of this device on the loop (A011), the type of device (MCP), the time at which the device entered
the alarm condition (11:45) and the Point Location Text (20 character description) for this device.

Dimension Series MORLEY-IAS
User Manual Document No.996-148-000-5, Revision: 5 Page 13
•To view other points in fire in this zone, press the Ïand Ðkeys (Note: The ‘R: more’ option is not
shown if there is only one event, the ‘↓’ and ‘↑’ keys are shown for the first and last entries in the list).
•To return to the list of zones in fire, press the Íkey.
4.2.1.3 Override Delays
EN54
9
EN54-2 7.11d
Override delays at
Level 1
•The DX1e, DX2e and DX4e control panels can be
configured to operate with delays to outputs. In this
case, a manual call point (MCP) will be located next
to the panel.
•To override any delays and immediately activate the
bells and other fire alarm output devices, break the
glass in the call point.
BREAK GLASS
Press Here
FIRE
4.2.2 Fault Conditions
•If the panel detects a fault, the FAULT LED is illuminated along with other appropriate system
condition LED Indicators. The internal buzzer will sound and the alphanumeric display will indicate the
number of faults.
•To view more detailed information regarding the fault locations use the navigation keys as follows.
•Press the ÍÏÐÎ keys to select the FAULT option and then press the 9key. The display shows
further information on the faults. For example:
TOTAL PANEL FAULTS :3 →:Panel Events
TOTAL ZONES IN FAULT :1 ↓:Zone Details
•This display indicates that there is one zone in fault and that three panel related faults have been
registered. To view these, press the Îkey to view the panel related faults and press the Ðkey to
view the zones in fault.
4.2.2.1 Panel Faults
FAULT 02/03 MON INPUT 1 12:15
INPUT OPEN CIRCUIT ←:back R:more
•The above example shows there are three panel related faults and fault number two is shown. This
was an input open circuit on “Monitored Input 1” registered at 12:15PM.
•If there is more than one fault indicated, use the Ïand Ðkeys to view these (Note: The ‘R: more’
option is not shown if there is only one event, the ‘↓’ and ‘↑’ keys are shown for the first and last entries
in the list). Press the Íkey to return to the main display.
4.2.2.2 Zone Faults
•When selected, the display shows the first zone with a fault condition. For example:
IN FAULT ZONE 1 01/01 R: More Zones
<Zone-Location-Text> →:Device Details
•The display shows the Zone number and Zone Location Text (20 character description).

MORLEY-IAS Dimension Series
Page 14 Document No. 996-148-000-5, Revision: 5 User Manual
•To view other zones in a fault condition (or to return to the main display), press the ÏÐkeys.
EN54
9
EN54-2 8.3
Fault Signals from
points.
•To view the devices (points) in a fault condition, press the Îkey. The
display then shows the first point in a fault condition in the selected
zone. For example:
FAULT 01/02 Z01 L1 A010 OPT 12:19
NO REPLY FROM DEVICE←:back R:more →:text
•The display shows the fault number and the total number of devices (points) in a fault condition in this
zone (01/02), the Zone number (Z01), the loop number to which this device is connected (L1), the
address of this device on the loop (A010), the type of device (OPT), the time at which the device
entered the alarm condition (12:19) and a description of the fault.
•To view other points in fault in this zone, press the ÏÐkeys (Note: The ‘R: more’ option is not shown
if there is only one event, the ‘↓’ and ‘↑’ keys are shown for the first and last entries in the list).
•To return to the list of zones in fault, press the Íkey.
•To view the location texts for this device press the Îkey. The display then shows the Zone Location
Text and the Point Location Text (20 character description each) for this device. For example:
FAULT 01/02 Z01 L1 S010 OPT 12:19
<Zone-Location-Text><Point-Location-Txt>
•To return to the previous display, press the Íkey.
4.2.3 Test Conditions
EN54
9
EN54-2 10
Test Condition.
•If zones have been configured to be in a test condition (i.e. weekly
walk test), the TEST LED is illuminated.
•To view the zones in a test conditions use the navigation keys as follows.
•Press the ÍÏÐÎ keys to select the TEST option and then press the 9key and the display shows
further information on the faults. For example:
IN TEST ZONE 1 01/02 WITH SOUNDERS
<Zone-Location-Text> ←:back R:More Zones
IN TEST ZONE 2 02/02 NO SOUNDERS
<Zone-Location-Text> ←:back R:More Zones
•The display shows the Zone number and Zone Location Text (20 character description) of the first
zone in a test condition. It also indicates whether the sounders / bells will ring briefly when a device in
the zone is tested.
•To view other zones in a test condition press the Ïand Ðkeys.
•To return to the previous display, press the Íkey.

Dimension Series MORLEY-IAS
User Manual Document No.996-148-000-5, Revision: 5 Page 15
4.2.4 Disablement Conditions
•If zones, input devices, output devices or other disablement conditions have been programmed, the
DISABLEMENT LED is illuminated along with other appropriate system condition LED Indicators.
•To view more detailed information regarding the disablement conditions use the navigation keys as
follows.
•Press the ÍÏÐÎ keys to select the DISABLED option, then press the 9key and the display shows
further information on the faults. For example:
TOTAL PANEL DISABLED :3 →:Panel Events
TOTAL ZONES DISABLED :3 ↓:Zone Details
•This display indicates that there are three zones in either a full or partial disablement condition and
that three panel related disablements have been configured. To view these, press the Îkey to view
the panel related disablement and press the Ðkey to view the zones in disablement.
4.2.4.1 Panel Disablements
DISABLED 01/03 12:15
DISABLE ALL SOUNDERS ←:back R:more
•The above example shows there are three panel related disablements and the first disablement is
shown. This was a disablement of all sounders / bells configured at 12:15PM.
•If there is more than one disablement indicated, use the Ïand Ðkeys to view these (Note: The ‘R:
more’ option is not shown if there is only one event, the ‘↓’ and ‘↑’ keys are shown for the first and last
entries in the list). Press the Íkey to return to the main display.
4.2.4.2 Zone Disablements
•When selected, the display shows the first zone with a disablement condition. For example:
DISABLED ZONE 1 01/03 R: More Zones
<Zone-Location-Text> ZONE FULLY DISABLED
•The display shows the Zone number and Zone Location Text (20 character description), the
disablement number and total number of zones in a disablement condition (01/03) and whether the
zone is fully disabled. If the zone is only partially disabled, the display is as follows:
DISABLED ZONE 1 02/03 R: More Zones
<Zone-Location-Text> →:Device Details
•To view other zones in a disablement condition (or to return to the main display), press the Ïand Ð
keys.
EN54
9
EN54-2 9.5
Disablement of
each addressable
point.
•To view the devices (points) in a zone with only partial disablement
condition, press the Îkey. The display then shows the first point in
disablement in the selected zone. For example: