Honeywell NOTIFIER FW-MM User manual

FIGURE 2. FACEPLATE INTERIOR
MAGNET LOCA
TION
(DO NOT REMOVE)
C1098-00
BATTERY REPLACEMENT
Low battery levels on the wireless devices are displayed as a trouble in the
FACP. Therefore when the message “TROUBLE BATTERY LOW” is displayed,
replace the battery in the device. This message is an indication that approxi-
mately one week of battery life remains.
COMPATIBILITY REQUIREMENTS
To ensure proper operation, this module shall be connected to a compatible
Notifier system control panel (list available from Notifier).
To replace the batteries in a wireless device use the following steps:
1. Have 4 CR123A (or DL123A) batteries available
2. Remove the faceplate from the module.
3. Open the battery compartment. (See Figure 3.)
4. Remove the used batteries and replace with new batteries. The battery com-
partment is designed such that the batteries can only align in the appropri-
ate direction. Do not force the batteries into the openings.
5. Replace the battery compartment cover.
6. Replace the faceplace.
SPECIFICATIONS
Maximum Operating Voltage: 3.3 VDC
Maximum Current Draw: 5.0 mA (LED on)
Average Operating Current: 210 µA, 3.9k EOL
EOL Resistance: 3.9K Ohms
Maximum IDC Wiring Resistance: 10 Ohms
Maximum IDC Voltage: 3.2 Volts
Maximum Average IDC Current: 5.5 µA
Maximum Transmit RF Power: 17 dBm
Radio Frequency Range: 902-928 MHz
Temperature Range: 32°F to 120°F (0°C to 49°C)
Humidity: 10% to 93% Non-condensing
Battery Type: 4 Panasonic CR123A or 4 Duracell DL123A
Battery Life: 2 year minimum
Battery Replacement: Upon TROUBLE BATTERY LOW display and/or during annual maintenance
Dimensions: 4¼ in. H x 4¼ in. W x 1½ in. D
Accessories: SMB500(-WH) electrical box (preferred mounting option)
BEFORE INSTALLING
This information is included as a quick reference installation guide. Refer to
the control panel installation manual and the SWIFT® Wireless Manual for
detailed system information. If the modules will be installed in an existing op-
erational system, inform the operator and local authority that the system will
be temporarily out of service. Disconnect power to the control panel before
installing the modules.
NOTICE: This manual should be left with the owner/user of this equipment.
GENERAL DESCRIPTION
The FW-MM(A) Monitor Module is intended for use with a wireless gateway
or wireless fire alarm control panel (FACP) to interface with a device having
contacts used to signal status conditions. The input to the monitor module is
non-latching and does not require a reset. The device communicates through
a robust, bi-directional mesh network to the gateway and/or FACP. Rotary
dial switches are provided for setting the module’s address. The module has a
panel controlled LED indicator. (See Figure 1.)
FIGURE 1. CONTROLS AND INDICATORS
C1095C-00
FACEPLATE
The faceplate includes a magnet for activation and tamper resistance. (See
Figure 2.) The faceplate magnet activates communication to the panel, there-
fore, the faceplate must be installed for the module to work properly. The
magnet also activates a supervisory tamper fault at the panel if the nameplate
is removed. Do NOT remove this magnet. The faceplate for a wireless module
CANNOT be replaced with the faceplate of a standard wired module.
1 I56-4067-005
7/27/2021
FW-MM(A) Wireless Monitor Module
I56-4067-005
INSTALLATION AND MAINTENANCE INSTRUCTIONS
12 Clintonville Road
Northford, CT 06472-1653
Phone: [phone]

2 I56-4067-005
©2021 Notifier. 7/27/2021
MOUNTING
The FW-MM(A) mounts directly to an SMB500(-WH) electrical box. (See
Figure 4.) To avoid interference with the wireless network metal elec-
trical boxes are NOT recommended. Non-metal surface mounted elec-
trical boxes (SMB500/SMB500-WH) are available from Notifier. If not
using an SMB500(-WH), the minimum mounting opening dimensions for the
FW-MM(A) are 4 in. X 3¾ in. x 1½ in. deep.
NOTE: Do not attach the module to temporary structures such that the place-
ment could be altered.
WIRING
NOTE: All wiring must conform to applicable local codes, ordinances, and reg-
ulations. This module is intended for power limited wiring only. FW-MM(A)
must be within 3 feet of monitored device when using field wiring or 20 feet
in non-metallic conduit. In Canada, wiring methods shall be in accordance
with CSA C22.1 Safety Standard for Electrical Installations, Canadian Electri-
cal Code, Part 1, Section 32.
1. Install module wiring in accor-
dance with the job drawings
and appropriate wiring dia-
grams.
2. Set the address on the module
per job drawings.
3. Secure module to electrical
box (supplied by installer), as
shown in Figure 3.
C1096-00
C1097-00
FIGURE 4. MODULE MOUNTINGFIGURE 3. BATTERY COMPARTMENT
BATTERY
COMPARTMENT
DOOR
BATTERY
COMPARTMENT
C2002-00
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.
WARNING: Do not make changes to the equipment. Changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment.
FCC STATEMENT
IC STATEMENT
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired operation of the device.
RAPPORT D’IC
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes: (1) l’appareil ne doit pas produire de
brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
INSTITUTO FEDERAL DE TELECOMUNICACIONES
This device utilizes the Honeywell915 rev A radio module and complies with IFETEL standard(s). IFT: RCPHOSW14-1983
Use of these products in combination with non-Honeywell products in a wireless mesh
network, or to access, monitor or control devices in a wireless mesh nework via the inter-
net or another external wide area network, may require a separate license from Sipco, LLC.
For more information, contact Sipco, LLC or Ipco, LLC at 8215 Roswell Rd., Building 900,
Suite 950, Atlanta, GA 30350, or at www.sipocollc.com or www.intusiq.com.
LICENSING STATEMENT
FIGURE 5. TYPICAL MONITORING CONFIGURATION
WIRELESS
MONITOR MODULE
ONLY ONE UL/ULC LISTED CONTACT
CLOSURE MAY BE USED
POWER LIMITED
3.1 VDC MAX
3.9K EOL
RESISTOR
A2143-10
INSTALL CONTACT CLOSURE DEVICES PER MANUFACTURER’S
INSTALLATION INSTRUCTIONS. WIRELESS MONITOR MODULE MUST BE
WITHIN 3 FEET (1M) OF MONITORED DEVICE WHEN USING FIELD WIRING
OR 20 FEET (6.1M) IN NON-METALLIC CONDUIT. C1099GC-00
Notifier®and SWIFT ® are registered trademarks of Honeywell International, Inc.