Honeywell SILENT KNIGHT IDP-Control User manual

LABEL
J1 UNDER LABEL
BACK OF
MODULE
K200-09-00 1 I56-2725-003
IDP-Control Supervised
Control Module
INSTALLATION AND
MAINTENANCE INSTRUCTIONS
Before Installing
This information is included as a quick reference installa-
tion guide. Refer to the control panel installation manual
for detailed system information. If the modules will be
installed in an existing operational system, inform the
operator and local authority that the system will be tem-
porarily out of service. Disconnect power to the control
panel before installing the modules.
NOTICE: This manual should be left with the owner/
user of this equipment.
General Description
IDP-Control Supervised Control Modules are intended
for use in intelligent, two-wire systems, where the in-
dividual address of each module is selected using the
built-in rotary switches. This module is used to switch an
external power supply to notification appliances. It also
supervises the wiring to the connected loads and reports
their status to the panel as NORMAL, OPEN, or SHORT
CIRCUIT. The IDP-Control has two pairs of output ter-
mination points available for fault-tolerant wiring and a
panel-controlled LED indicator.
Figure 1A. Controls
and indicators:
Figure 2A. Module mounting with barrier:
C0219-01
C0217-01
Specifications
Normal Operating Voltage: 15 to 32 VDC
Maximum Current Draw: 6.5 mA (LED on)
Average Operating Current: 390µA (LED flashing)
Regulated External
Supply Voltage: (between Terminals T3 and T4)
Maximum: 80 Volts (RMS or DC)
Drain on External Supply: 2 mA Maximum (using
internal EOL relay)
Temperature Range: 32°F to 120°F (0°C to 49°C)
Humidity: 10% to 93% non-condensing
Dimensions: 41/2˝ H x 4” W x 11/4˝ D
(Mounts to a 4˝ square by
21/8˝ deep box.)
Accessories: SMB500 Electrical Box
Compatibility Requirements
To ensure proper operation, this module shall be con-
nected to a compatible Silent Knight system control pan-
els only (list available from Silent Knight).
Mounting
The IDP-Control mounts directly to 4 square electri-
cal boxes (see Figure 2A). The box must have a mini-
mum depth of 21/8˝. Surface mounted electrical boxes
(SMB500) are available.
Wiring
NOTE: All wiring must conform to applicable local
codes, ordinances, and regulations. When using control
modules in nonpower limited applications, UL require-
ments for the separation of power-limited and nonpower-
limited terminals and wiring must be met. The barrier
must be inserted into a 4˝ × 4˝ × 21/8˝ junction box, and
the control module must be placed into the barrier and
attached to the junction box (Figure 2A). The power-lim-
ited wiring must be placed into the isolated quadrant of
the module barrier (Figure 2B).
9
8
7
6
54
3
2
1
0
0
1
2
3
4
56789
TENS
ONES
ADDRESS
LOOP
10
78
6
5
4
3
2
9
ISOLATED
QUADRANT
0
1
2
3
4
9
8
7
6
5
0
TENS
ONES ADDRESS
LOOP
9
8
7
6
5
4
3
21
0
9
8
7
6
5
4
3
21
0
1
2
3
4
9
8
7
6
5
0
TENS
ONESADDRESS
LOOP
9
8
7
6
5
4
3
21
0
9
8
7
6
5
4
3
21
Figure 1B. Jumper location:
C0458-00
Figure 2B:
C0218-01

MODULE
FROM PANEL OR
(+)
(-)
TO NEXT
(+)
(-)
DEVICE
(+)
(-)
CONTROL
(-)
(+)
47K EOL
RESISTOR
ELR-47K
UL LISTED EOL RELAY
SHOWN ENERGIZED
24 VDC COIL
EOLR-1 TO NEXT CONTROL MODULE OR END-OF-LINE-RELAY.
ONE RELAY REQUIRED FOR EACH CIRCUIT.
MODULE POLARITIES ARE
SHOWN IN ALARM
CONNECT MODULES TO LISTED COMPATIBLE
32 VDC MAX.
IS RECOMMENDED
24 VDC CIRCUIT
3 & 4. BREAK WIRE RUN TO PROVIDE
SUPERVISION OF CONNECTIONS.
DO NOT LOOP WIRE ON TERMINALS
ALL WIRING SHOWN IS SUPERVISED AND POWER LIMITED
(-)
(+)
TWISTED PAIR
SILENT KNIGHT CONTROL PANELS ONLY
PREVIOUS DEVICE
(-)
(+)
24 VDC POWER SUPPLY
ISOLATED, REGULATED, POWER
LIMITED PER NFPA 70.
LISTED FOR FIRE PROTECTION WITH
BATTERY BACKUP.
9
8
7
6
5 4
3
2
1
0
0
1
2
3
4
5 6 7 8 9
TENS
ONES
ADDRESS
LOOP
0
7 8
6
5
4
3
2
1
9
SIGNAL LINE CIRCUIT (SLC)
MODULE
FROM PANEL OR
(+)
(–)
TO NEXT
(+)
(–)
DEVICE
(+)
(–)
CONTROL
(–)
(+)
(–)
(+)
UL LISTED EOL RELAY
SHOWN ENERGIZED
24VDC COIL
EOLR-1
MODULE POLARITIES ARE
SHOWN IN ALARM
CONNECT MODULES TO LISTED COMPATIBLE
24 VDC CIRCUIT
3 & 4. BREAK WIRE RUN TO PROVIDE
SUPERVISION OF CONNECTIONS.
DO NOT LOOP WIRE ON TERMINALS
ALL WIRING SHOWN IS SUPERVISED
AND POWER LIMITED
(+)
SILENT KNIGHT CONTROL PANELS ONLY
PREVIOUS DEVICE
EOL RESISTOR IS
INTERNAL AT
TERMINALS 8 & 9
32 VDC MAX.
TWISTED PAIR
IS RECOMMENDED
(–)
24 VDC POWER SUPPLY
ISOLATED, REGULATED, POWER
LIMITED PER NFPA 70.
LISTED FOR FIRE PROTECTION WITH
BATTERY BACKUP.
TO NEXT CONTROL MODULE OR END-OF-LINE-RELAY.
ONE RELAY REQUIRED FOR EACH CIRCUIT.
9
8
7
6
5 4
3
2
1
0
0
1
2
3
4
5 6 7 8 9
TENS
ONES
ADDRESS
LOOP
0
7 8
6
5
4
3
2
1
9
SIGNAL LINE CIRCUIT (SLC)
K200-09-00 2 I56-2725-003
Figure 3. Typical notification appliance circuit configuration, NFPA Style Y:
Figure 4. Typical fault tolerant notification appliance circuit configuration, NFPA Style Z:
C0808-03
C0807-03
WARNING
All relay switch contacts are shipped in the standby state (open) state, but may have transferred to the activated (closed)
state during shipping. To ensure that the switch contacts are in their correct state, modules must be made to communi-
cate with the panel before connecting circuits controlled by the module.
1. Install module wiring in accordance with the job draw-
ings and appropriate wiring diagrams.
2. Set the address on the module per job drawings.
3. Secure module to electrical box (supplied by installer),
as shown in Figure 2A.
IMPORTANT: When using the IDP-Control for fire
fighter telephone applications, remove Jumper (J1) and
discard. The Jumper is located on the back under the
product label as shown in Figure 1B. 7550 Meridian Circle
Maple Grove, MN 55369-4927
763-493-6455; 800-328-0103
Fax: [phone]
http://www.silentknight.com
© 2006 Silent Knight 8/05