Honeywell Silent Knight IDP-Monitor User manual

C0218-01
C0156-00
C0157-00
Figure 1. Controls and Indicators:
Specifications
Normal Operating Voltage: 15 to 32 VDC
Maximum Current Draw: 5.0 mA (LED on)
Average Operating Current: 375µA (LED flashing)
EOL Resistance: 47K Ohms
Maximum IDC
wiring resistance: 1,500 Ohms
Temperature Range: 32°F to 120°F (0°C to 49°C)
Humidity: 10% to 93% Non-condensing
Dimensions: 41⁄2˝ H x 4˝ W x 11⁄4˝ D
(Mounts to a 4˝ square by
21⁄8˝ deep box.)
Accessories: SMB500 Electrical Box
Figure 2B:
Figure 2A. Module mounting:
NOTE: For UL Listed security installations, the IDP-Monitor
must be mounted within the control panel enclosure.
Before Installing
This information is included as a quick reference installa-
tion guide. Refer to the control panel installation manual
for detailed system information. If the modules will be
installed in an existing operational system, inform the
operator and local authority that the system will be tem-
porarily out of service. Disconnect power to the control
panel before installing the modules.
NOTICE: This manual should be left with the owner/
user of this equipment.
General Description
The IDP-Monitor Module is intended for use in intel-
ligent, two-wire systems, where the individual address of
each module is selected using the built-in rotary switches.
It provides either a Class A or Class B fault tolerant initi-
ating device circuit (IDC) for normally open contact fire
alarm and supervisory devices, or either normally open or
normally closed security devices. The module has a panel
controlled LED indicator.
Compatibility Requirements
To ensure proper operation, this module shall be con-
nected to a compatible Silent Knight system control panel
(list available from Silent Knight).
INSTALLATION AND MAINTENANCE
INSTRUCTIONS
K200-08-00 1 I56-2724-002
0
1
2
3
4
9
8
7
6
5
0
TENS
ONES ADDRESS
LOOP
9
8
7
6
5
4
3
21
0
9
8
7
6
5
4
3
21
0
1
2
3
4
8
7
6
5
9
ONES
ADDRESS
TENS
10
2
3
4
5
6
789
10
2
3
4
5
6
789
9
8
7
6
54
3
2
1
0
0
1
2
3
4
56789
TENS
ONES
ADDRESS
LOOP
10
78
6
5
4
3
2
9
IDP-Monitor Module
Mounting
The IDP-Monitor mounts directly to 4˝ square electri-
cal boxes (see Figure 2A). The box must have a mini-
mum depth of 21⁄8˝. Surface mounted electrical boxes
(SMB500) are available from Silent Knight.
Wiring
NOTE: All wiring must conform to applicable local
codes, ordinances, and regulations. This module is in-
tended for power limited wiring only.
1. Install module wiring in accordance with the job draw-
ings and appropriate wiring diagrams.
2. Set the address on the module per job drawings.
3. Secure module to electrical box (supplied by installer),
as shown in Figure 2A.

9
8
7
6
54
3
2
1
0
0
1
2
3
4
5
678
9
TENS
ONES
ADDRESS
LOOP
0
7
8
6
5
4
3
2
1
9
FROM PANEL OR
(+)
(–)
TO NEXT
(+)
(–)
DEVICE
(+)
(–)
MONITOR
CONNECT MODULES TO LISTED COMPATIBLE
32 VDC MAX.
SHIELDED-TWISTED PAIR
IS RECOMMENDED
SILENT KNIGHT CONTROL PANELS ONLY
PREVIOUS DEVICE
ALL WIRING SHOWN IS SUPERVISED AND POWER LIMITED
COMMUNICATION LOSS (OPTIONAL CONNECTION FOR
PANELS WHICH SUPPORTTHIS FEATURE)
47 K EOL
RESISTOR
ELR-47K
ANY NUMBER OF UL LISTED CONTACT CLOSURE
DEVICES MAYBE USED. DO NOT MIX FIRE
ALARM INITIATING, SUPERVISORY
, OR
SECURITY DEVICES ON THE SAME MODULE.
INITIATING DEVICE CIRCUIT (IDC) - NFPASTYLE B
POWER LIMITED: 230A MAX @ 12 VDC MAX
INSTALL CONTACT CLOSURE DEVICES PER
MANUFACTURER'S INSTALLATION INSTRUCTIONS.
MODULE
14K SERIES RESISTOR
SIGNAL LINE CIRCUIT (SLC)
9
8
7
6
54
3
2
1
0
0
1
2
3
4
5
6
7
8
9
TENS
ONES
ADDRESS
LOOP
0
7
8
6
5
4
3
2
1
9
MODULE
FROM PANEL OR
(+)
(-)
TO NEXT
(+)
(–)
DEVICE
(+)
(–)
MONITOR
CONNECT MODULES TO LISTED COMPATIBLE
SILENT KNIGHT CONTROL PANELS ONLY
PREVIOUS DEVICE
ALL WIRING SHOWN IS SUPERVISED AND POWER LIMITED
EOL RESISTOR
IS INTERNAL AT
TERMINALS 8 & 9.
ANY NUMBER OF UL LISTED CONTACT CLOSURE
DEVICES MAY BE USED. DO NOT MIX FIRE
ALARM INITIATING, SUPERVISORY, OR
SECURITY DEVICES ON THE SAME MODULE.
INSTALL CONTACT CLOSURE DEVICES PER
MANUFACTURER'S INSTALLATION INSTRUCTIONS.
32 VDC MAX
SHIELDED-TWISTED PAIR
IS RECOMMENDED
COMMUNICATION LOSS (OPTIONAL CONNECTION
FOR PANELS WHICH SUPPORT THIS FEATURE)
SIGNAL LINE CIRCUIT (SLC)
9
8
7
6
54
3
2
1
0
0
1
2
3
456789
TENS
ONES ADDRESS
LOOP
0
78
6
5
4
3
21
9
(+)
(–)
(+)
(–)
(+)
(–)
MONITOR
ALL WIRING SHOWN IS SUPERVISED AND POWER LIMITED
COMMUNICATION LOSS (OPTIONAL CONNECTION FOR
PANELS WHICH SUPPORTTHIS FEATURE)
47 K EOL
RESISTOR
ELR-47K
ANY NUMBER OF UL LISTED CONTACT CLOSURE
DEVICES MAYBE USED. DO NOT MIX FIRE
ALARM INITIATING, SUPERVISORY
, OR
SECURITY DEVICES ON THE SAME MODULE.
INITIATING DEVICE CIRCUIT (IDC) - NFPASTYLE B
POWER LIMITED: 230A MAX @ 12 VDC MAX
INSTALL CONTACT CLOSURE DEVICES PER
MANUFACTURER'S INSTALLATION INSTRUCTIONS.
MODULE
SIGNAL LINE CIRCUIT (SLC)
32 VDC MAX.
TWISTED PAIR
IS RECOMMENDED
FROM PANEL OR
PREVIOUS DEVICE
CONNECT MODULES TO LISTED COMPATIBLE
SILENT KNIGHT CONTROL PANELS ONLY
TO NEXT
DEVICE
C0805-01
C0804-01
C0806-01
Figure 5. Typical 2-wire initiating circuit configuration for security systems (with alarm versus short capability):
NOTE: For UL Listed security installations, the IDP-Monitor must be mounted within the control panel enclosure.
Figure 4. Typical 4-wire fault tolerant initiating circuit configuration, NFPA Style D:
Figure 3. Typical 2-wire initiating circuit configuration, NFPA Style B:
K200-08-00 2 I56-2724-002
7550 Meridian Circle
Maple Grove, MN 55369-4927
763-493-6455; 800-328-0103
Fax: [phone]
http://www.silentknight.com
© 2006 Silent Knight 8/05