Honeywell Evohome User manual

evohome
Installation
Guide

evohome Controller
Digital Room Thermostat
(DTS92)
Wireless Relay Box (BDR91)Wireless Cylinder Thermostat
Transceiver (CS92)
Wireless Cylinder Thermostat
Strap-on Sensor (CS92)
Wireless Cylinder Thermostat
Insertion Sensor (CS92)
Radiator Controller (HR92)
Remote Access Gateway
(RFG100)
Radiator Controller (HR80)
Wireless OpenTherm Bridge
(R8810)
Mixing Valve Controller
(HM80)
Underfloor Heating Controller
(HCE80 or HCC80)
evohome Controller Wall
Bracket (ATF300 )
evohome Controller Table Stand
(ATF100 or ATF200)
Room Temperature Sensor
(HCW82)
Room Temperature Sensor
(HCF82)
Icon key

Thanks for choosing evohome
evohome means more comfort, and more control
of the heating system. It’s simple to install and easy
to use.
Follow these instructions to set up the evohome
system. Devices that need to be connected to the
mains electricity supply should be installed by a
competent person.
Before you start
Make sure you have all the devices you need for
your system. If you used our ‘Design your evohome
system’ guide, match each device to the room or
zones in your plan. It’s a good idea to carry out all
the mains electrical and other wiring work first.
In this guide
Step 1: Wire up the heating system 3
Step 2: Set up your evohome Controller 9
Step 3: Power up and bind devices 13
Step 4: System test 29
Configuration and modification 37
Appendix 41
1evohome Installation Guide

Step 2: Set up your evohome Controller
Power up the evohome Controller and follow the on-screen instructions for your system
Go to Installer Menu Go to Guided Configuration Go to Home screen
You have…
a Base Pack or a
Connected Pack
+
Un-bound devices
You have…
an un-bound evohome
Controller
+
Un-bound devices
You have…
a Base Pack or a
Connected Pack
+
No additional devices
Step 3: Power up and bind devices
Power up all devices, including the battery powered ones,
and bind them to the evohome Controller
Step 1: Wire up your heating system
Connect all mains powered devices to the heating system
Step 4: Test the system
Check that all the devices are working properly
2Step 1: Wire up the heating system

In this section
Wireless Relay Box (BDR91) 4
Wireless Cylinder Thermostat (CS92) 5
Remote Access Gateway (RFG100) 7
Mixing Valve Controller (HM80), Underfloor Heating Controller (HCE80/HCC80),
Opentherm Bridge (R8810) 8
Step 1: Wire up the
heating system
evohome communicates using wireless on a robust 868Mhz
signal that is unaffected by common remote controls or Wifi.
Some devices need mains power or to be connected to external
equipment and it's best to wire up these items first to simplify the
binding process later in the setup. The evohome controller will give
on screen instructions when these should be powered up.
Before you power up your evohome Controller and install
the radiator controllers, it's best to install any devices which
are mains powered or need specific installation.
3evohome Installation Guide

Turn off at mains and isolate
the supply before starting
!If you’re fitting a Wireless Relay Box
(BDR91) to your boiler, zone valve or
Sundial valve
1Mount the Wireless Relay Box on a non-metal surface at least
30cm from your boiler, other wireless device or metal objects
2Release the clip on the bottom to open the front cover
3Follow the wiring diagram (see Appendix: Figures
5-10) to connect the Wireless Relay Box to your
boiler’s thermostat terminals, zone valve or sundial
valve, and to the mains electricity supply
4Replace the cover
BOILER
1
4
Refer to boiler instruction to locate the room thermostat terminals,
determine if the boiler required a permanent live supply.
MINIMUM
30CM
REPLACE
FRONT
COVER
Wireless Relay Box (BDR91)
4Step 1: Wire up the heating system

If you’re fitting a Wireless Cylinder
Thermostat (CS92)
You will need to install the CS92 Transceiver
and only one of the two sensors (CS92 Strap-
on Sensor or CS92 Insertion Sensor).
To fit the CS92 Strap-on Sensor
1Cut away a section of cylinder insulation
slightly larger than the sensor unit
2Clean the exposed cylinder surface
3Place the sensor on the cylinder surface
and secure it using the fixing strap – cut
the strap to size if it’s too long
4Install the CS92 Transceiver in a suitable location
close enough for the cable from the sensor to reach
5Connect the cable from the sensor
to the CS92 Transceiver
Position the sensor from one quarter to a
third of the way up the cylinder.
13
1/4 – 1/3
TOTAL
HEIGHT
45MM
80MM
MINIMUM
30CM
A x B Cy
A x B Cy
Wire to CS92 Transceiver
5
Wireless Cylinder Thermostat (CS92)
5evohome Installation Guide

To fit the CS92 Insertion Sensor
1Fit in the cylinder immersion well with suitable fittings to
provide strain relief and prevent accidental removal
2If the sensor doesn’t fit tightly in the immersion
well fill the space with heat-conductive compound
to ensure maximum heat transfer
3Install the CS92 Transceiver in a suitable location close
enough for the cable from the sensor to reach
4Connect the cable from the sensor to the CS92 Transceiver
4
A x B Cy
A x B Cy
Wire to CS92 Transceiver
Wireless Cylinder Thermostat (CS92) continued
6Step 1: Wire up the heating system

If you’re fitting a Remote Access
Gateway (RFG100)
1Connect the Remote Access Gateway to the home’s
internet router using the ethernet cable supplied
Remote Access Gateway (RFG100)
7evohome Installation Guide

If you’re fitting a Mixing Valve
Controller (HM80), Underfloor
Heating Controller (HCE80/HCC80),
OpenTherm Bridge (R8810)
Refer to the installation instructions
supplied with each device
Mixing Valve Controller (HM80), Underfloor Heating
Controller (HCE80/HCC80), OpenTherm Bridge (R8810)
8Step 1: Wire up the heating system