Honeywell HD-DVR-1004 User manual

© 2011 Honeywell International Inc. All rights reserved.
Honeywell
HD-DVR-1004
HD-DVR-1008
HD-DVR-1016
Digital Video Recorder
User Manual
http://www.tronikaonline.com

Web Client Operation
102
6 Web Client Operation
Note
•All the operations here are based on HD-DVR-1016.
•There might be slight differences in the interface due
to the updated series.
Network Connection
Before the web client operation, please check the following items:
•Network connection is right
•DVR and PC network setup is right. Please refer to network setup (main
menusettingnetwork)
•Use order ping ***.***.***.***(* DVR IP address) to verify that there is a
good connection. Usually, the return TTL value should be less than 255.
•Open the IE and then input DVR IP address.
•System can automatically download latest web controls and the new
version can overwrite the previous one.
•If you want to un-install the web control, please run uninstall
webrec2.0.bat. Or you can go to C:\Program Files\webrec to remove
single folder. Please note, before you un-install, please close all web
pages, otherwise the un-installation might result in error.
Login
Open IE and input DVR address in the address column. For example, if
your DVR IP is 10.10.3.16, then please input http:// 10.10.3.16 in IE
address column. See Figure 6-1

Honeywell
103
Figure 6-1 Sample of IE Login
A system pop up with warning information will ask you if you want to install
webrec.cab control. Please click yes button.
If you can’t download the ActiveX file, please modify your settings as
follows, enable or prompt all disabled Active X items. See Figure 6-2 and
Figure 6-3.
Input your IP
address here.

Web Client Operation
104
Figure 6-2 The Internet Options Window

Honeywell
105
Figure 6-3 The Settings for ActiveX
After installation, the interface is shown as below. See Figure 6-4 Please
input your user name and password.
Default factory name is admin and password is admin.
Note For security reasons, please modify your password after
you first login.

Web Client Operation
106
Figure 6-4 The Web Login Window
After you logged in, you can see the main window. See Figure 6-7
This main window can be divided into the following sections.
Section 1: There are five function buttons: configuration, search, alarm,
about, and log out .
•Section 2: There are channel number buttons and four function buttons:
open all, start dialog, local play, and refresh.
•Section3: There are PTZ controls (see PTZ), color (see Color)buttons,
and you can also select the picture path and the record path.
•Section 4: Real-time monitor window. Please note current preview
window is circled by a green rectangle zone.
•Section 5: Here you can view window switch button. You can also select
video priority between fluency (smooth playback quality) or real-time
(low latency).
oSystem monitor window switch supports full screen/1-window/4-
window/6-window/8-window/9-window/13-window/16-window/20-
window/25-window/36-window. See Figure 6-5.
Figure 6-5 The Window Switch Menu
oPreview window switch. System support 1/4/8/9/16-window real-
time preview. Please you need to have the proper rights to
implement preview operation. You cannot preview if you have no
right to preview the either channel. See Figure 6-6.

Honeywell
107
Figure 6-6 The Preview Window Switch Menu
Figure 6-7 The Main Menu of Web Client
Real-Time Monitor
In section 2, left click the channel name you want to view, you can see the
corresponding video in the current window.
On the top left corner, you can view device IP, channel number, and
network monitor bit stream.
Figure 6-8 Status Information
There are six function buttons in the top right corner. See Figure 6-9.
Figure 6-9 Control Setup
1 2 3 4 5 6
1 2 3
Section1
Section 2 Section 3
Section 5 Section 4

Web Client Operation
108
•1: Digital zoom: Click this button and then left drag the mouse in the
zone to zoom in. Right clicking mouse system restores original status.
•2: Change show mode: resize or switch to full screen mode.
•3: Local record. When you click the local record button, the system
begins recording and this button becomes highlighted. You can go to the
system folder RecordDownload to view the recorded file. Clicking the
highlighted button will stop local recording, and the button will resume
original status.
•4: Capture picture. You can snapshoot important video. All images are
memorized in system client folder \download\picture (default).
•5: Audio: Turn on or off audio (this has no relationship with system audio
setup).
•6: Close video.
Please refer to Figure 6-10for the main stream and extra stream switch
information.
Figure 6-10 Switch between the Main Stream and Extra Stream
Note If a DVR user changes channel names locally, manual
refresh (F5) of the web page is required to update the
channel names in the web client.
Open All
You can click it to open all channels.
Refresh
You can use button to refresh camera list.
Start Dialogue
You can click this button to enable audio talk.
Local Play
Click Local Play, and the system pops up the following interface for you to
select local play file. See Figure 6-11