Honeywell HRTL-One DVR User manual

HRTL-One DVR Quick Start Guide
For Front Panel Operation, see over.
Step 1: Unpack everything
Your HRTL-One comes with the following items:
• One single channel HRTL-One Digital Video Recorder
• One hard drive cartridge (hard drive not included) and a
key for the cartridge (located inside drive carrier)
• One power converter and power cord
• One rack mounting kit
• HRTL-One Digital Video Recorder User Guide
• External I/O connector
• 80 GB Hard Drive (included with HRTL-One-80 DVR,
not included with HRTL-One DVR)
Step 2: Remove the hard drive cartridge
Ensure HRTL-One is powered off.
HDD HDD Full ALARM TIMER PLAY REC
MENU ENTER SEARCH SLOW POWER
REC
PAUSE / Up
REW
Left
STOP / Down
FF
Right
Hard drive
1. Pull handle towards you.
2. Insert key and
turn to B
position.
A
B
cartridge frame
New HD Carrier Original HD Carrier
Key
Active handle
3. Remove carrier body from cartridge frame. Set aside.
Cartridge frame
Carrier body
Original HD Carrier
New HD Carrier
4. Remove top cover.
Release Latch
Release Latch
Original HD Carrier
New HD Carrier
Step 3: Install hard drive
5. Ensure hard drive is configured as Master. Refer to the
documentation that came with the hard drive for the
jumper settings.
Step 4: Connect equipment
Figure 1 Single camera installation
PC power cable
IDE ribbon cable
6. Insert cables on hard drive.
PC power cable
IDE ribbon cable
Original HD CarrierNew HD Carrier
7. Secure the hard drive into the hard drive cartridge using
the four #6-32 screws supplied.
New HD Carrier Original HD Carrier
8. Replace top cover and insert the carrier
body into the HRTL-One cartridge frame.
New HD Carrier
Original HD Carrier
Cartridge frame
Carrier body
Carrier body
Top Cover
9. Turn the key lock to the Aposition before
powering on. This will ensure that the hard drive
functions normally.
A = ON (Locked, hard drive cannot be removed)
B = OFF (Unlocked, hard drive can be removed)
A
B
DVR

HRTL-One DVR Quick Start Guide
www.honeywellvideo.com
+1.800.796.CCTV
Specifications subject to change without notice.
Imperial conversions are approximate.
© 2004 Honeywell International Inc.
Document 900.0260 Rev 1.00 10/04
Figure 2 Multiple cameras via multiplexer
Step 5: Program the HRTL-One
1. After powering up, press MENU on the HRTL-One and
enter your password (default 0000).
2. Program the HRTL-One:
Step 6: Operate the HRTL-One
HRTL-One Recorder Functions
Switch out
Setting Path to menu screen
Internal alarm buzzer Main Menu
➤ System
On-screen display (Date display) Main Menu
➤ System
Date and Time Main Menu
➤ System
HDD Overwrite (select Yes or No)
Yes = Continue to record newest image
over oldest when hard drive is full (optional)
Main Menu
➤ System
Change your password (optional) Main Menu
➤ System
Timed daily recording and holiday schedules
(Timer Enable; select Yes to use timed
recording)
Main Menu
➤ Timer
Images per second ratio, record quality,
recording mode (select Frame or Field)
Main Menu
➤ Record
How system responds to an alarm event Main Menu
➤ Alarm
Control HRTL-One from a remote device Main Menu
➤ Remote
HDD HDD Full ALARM TIMER PLAY REC
MENU ENTER SEARCH SLOW POWER
REC
PAUSE / Up
REW
Left
STOP / Down
FF
Right
LEDs
Controls
Control Press to …
MENU Enter the Main menu setup, enter the password (default: 0000).
ENTER Accept changes that you make in menu setup.
SEARCH Search for previously recorded video.
SLOW Slow down the speed of Play mode.
(X1/2, X1/4, X1/8, X1/16, X1/32)
STOP Stop recording or playing.
REC Start recording in manual recording mode. Manual recording overrides
timed recording configured in the menu setup.
POWER Power up the HRTL-One. Press again to power off the HRTL-One.
REW (Left) Play video backward at high speed. Continue pressing to adjust the speed
(1X, 2X, 4X, 8X, 16X, 32X).
FF (Right) Play video forward at high speed. Continue pressing to adjust the speed
(1X, 2X, 4X, 8X, 16X, 32X).
PAU SE Pause the video at the currently displayed image.
PLAY Play recorded video.
LEDs
The red light is ON, when:
Record Video
• When an alarm triggers recording
• When an external trigger starts recording
• As scheduled on the Timer screen
• Manually, when you press REC on the front panel
Play Back Video
1. Press PLAY to display the last recorded video clip.
2. Press SLOW for slow play back, REW to play video in
reverse at high speed, or FF to play video forward at
high speed.
Play Back Single Images
1. Press PLAY, then press PAUSE to lock the current
image on the screen.
2. Press  to select single image play. Continue to press
 to move forward, image by image.
To view single images in reverse, press .
Search for Video Clips
1. Press SEARCH.
2. Select from:
3. Press Enter to play the desired video.
HDD The hard drive is activated.
HDD FULL The hard drive is full.
ALARM When alarm enable is set to Yes and an alarm is
triggered, the LED flashes red.
TIMER When timer enable is Yes.
PLAY The HRTL-One is in play mode.
REC The HRTL-One is in record mode.
Last Record
Full List
Alarm List
Time Search

Field Displays
Last Record The last recorded video
Full List Complete list of recorded video,
sorted by time.
Alarm List Recorded alarms, sorted by time.
Time Search Enter time parameters to search
for video.