Honeywell Graceshire 51859 User manual

Home
Model #51859, 51860
Graceshire Ceiling Fan
User Manual
Read and save these instructions before use

EN I2
PACKAGE CONTENTS
HARDWARE CONTENTS
Mounting Bracket Screw (x4)
Mounting Bracket
Blade (x5)
Motor Assembly
Fitter Plate
Light Pan
Fitter Plate
Screw (x3)
Light Pan
Screw (x3)
Light Kit
Bowl Assembly Remote Pack Blade Balancing Kit
Blade Screw (x15) Blade Washer (x15)Wire Connector (x3)
Note: Some extra hardware may be included. The quantity listed above is the number required for installation.
Secondary Spring
Washer
Support WasherSecondary Support Screw

EN I3
SAFETY INFORMATION
THANK YOU
Please read and understand this entire manual before attempting to assemble, operate or install the product.
• Before you begin installing the fan, disconnect the power by removing fuses or turning off the circuit breakers.
• Make sure all electrical connections comply with local codes, ordinances, the National Electrical Code and ANSI/NFPA 70-
199. Hire an electrician or consult a do-it-yourself handbook if you are unfamiliar with installing electrical wiring.
• Make sure the installation site you choose allows a minimum of 7 feet from the blades to the floor and at least 30 inches from
the tip of the blades to any obstruction.
• RATED FOR INDOOR LOCATIONS ONLY. The fan is not suitable for damp or outdoor locations.
• The weight of the fan is 13.93 pounds.
DANGER: When using an existing outlet box, make sure it is securely attached to the building structure and can support
the full weight of the fan. Failure to this can result in serious injury or death. The stability of the outlet box is essential in
minimizing wobble and noise in the fan after installation is complete.
WARNING: Using a full-range dimmer switch to control fan speed will cause a humming sound from the fan. To reduce the
risk of fire or electric shock, do NOT use a full-range dimmer switch to control fan speed.
WARNING: To reduce the risk of fire, electric shock or personal injury, mount the fan to an outlet box marked
“ACCEPTABLE FOR FAN SUPPORT” and use the mounting screws provided with the outlet box. Most outlet boxes commonly
used for the support of lighting fixtures are not acceptable for fan support and may need to be replaced. Consult a qualified
electrician if in doubt. Secure the outlet box directly to the building structure. The outlet box and its support must be able to
support the moving weight of the fan (at least 35 lbs.).
WARNING: To reduce the risk of fire, electric shock or personal injury, wire connectors provided with this fan are designed to
accept only one 12-gauge house wire and two lead wires from the fan. If your house wire is larger than 12-gauge and/or there is
more than one house wire to connect to the two fan lead wires, consult an electrician for the proper size wire connectors to use.
WARNING: To reduce the risk of fire, electric shock or personal injury, do not bend the blade arms when installing them,
balancing the blades or cleaning the fan. Do not insert objects between the rotating fan blades.
WARNING: To reduce the risk of personal injury, use only parts provided with this fan. The use of parts other than those
provided with this fan will void the warranty.
CAUTION: Be sure the outlet box is properly grounded or a ground (green or bare) wire is present.
CAUTION: Carefully check all screws, bolts, and nuts on the fan assembly ensure they are secured.
Honeywell Ceiling Fans feature a collection of fans in various sizes and specifications to ensure your choice of indoor or outdoor
fan delivers optimum performance for your room’s size. You can trust the quality of Honeywell Ceiling Fans to deliver maximum
airflow and stylish lighting options. Honeywell Ceiling Fans use high-quality materials that are long lasting and durable to
deliver a great look and last for years to come.

EN I4
CARE AND MAINTENANCE
At least twice each year, check and tighten all screws on the fan. Clean the motor housing and blades with a soft brush or lint-
free cloth to avoid scratching the finish.
Total fixture wattage is 23 watts; do not attempt to replace.
Battery Replacement: Use CR2032 lithium batteries. Exhausted batteries should be removed from remote. Non-rechargeable
batteries should not be recharged. Do not dispose of batteries in fire, as they may explode.
Important: Shut off the main power supply before you begin any maintenance task. Do NOT use water or a damp cloth to clean
the fan.
CAUTION: This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following
two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device (if applicable).
CAN ICES-003 (B) / NMB-003 (B)
CAN ICES-005 (B) / NMB-005 (B)
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more
of the following measures:
--Reorient or relocate the receiving antenna.
--Increase the separation between the equipment and receiver
--Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
--Consult the dealer or an experienced radio/TV technician for help.
Please note changes or modifications not expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
HKC-US
3350 Players Club Parkway #225
Memphis, TN 38125
1-877-361-3883
SAFETY INFORMATION

EN I5
INITIAL INSTALLATION
PREPARATION
Before beginning the assembly of this product, ensure all parts are present. Compare all parts with the package contents list
and hardware contents list. If any part is missing or damaged, do not attempt to assemble the product.
Estimated assembly time: 2 hours
Tools required (not included): Phillips and Flat-head Screwdrivers, Safety Glasses, Step Ladder, Wire Cutter, and Wire Stripper.
1. Turn off power to the fan at the breaker box and the wall switch (Figure 1.1). DANGER: Failure to disconnect the power supply
prior to installation may result in serious injury or death.
2. This fan is intended for Flushmount Installation. Standard Mounting, Angle Mounting, and Closemount installations are not
available (Figure 1.2).
3. When selecting a location for installation, ensure the blades will be at least 30 inches from any wall or obstruction and at
least 7 feet above the floor (Figure 1.3).
1. Loosen all four mounting bracket screws, then completely remove two mounting bracket screws from opposite sides of the
mounting bracket (Figure 2.1).
2. Install the mounting bracket to the outlet box (sold separately) using the screws and washers provided with the outlet box.
WARNING: To reduce the risk of fire, electric shock, or personal injury, mount to the outlet box marked “acceptable for fan
support” (Figure 2.2).
3. Raise the fan and place top of the motor assembly on the hook on the mounting bracket, temporarily leaving hands free for
the wiring process (Figure 2.3).
Standard Mounting
Flushmount Closemount
Angle Mounting
Figure 1.1
Figure 2.1
Figure 1.2
Mounting Bracket
Outlet Box
Figure 2.2
Figure 1.3
Figure 2.3
Mounting Bracket Screw
Mounting Bracket
Mounting Bracket
Hook
7 feet
minimum
30 in.
minimum

EN I6
Figure 3.2Figure 3.1 Figure 3.3
Braided Cable
Brace
Open Loop Secondary Support Screw
Support
Washer
Spring
Washer
Secondary
Support Screw
SECONDARY HANGING SYSTEM INSTRUCTIONS
1. WARNING: Secondary support is required for this product. Failure to follow the steps below could result in property damage
and/or personal injury. Feed the loop of the braided cable, preassembled to the motor assembly, up through the outlet box
mounted in the ceiling (Figure 3.1).
2. Install secondary support screw, spring washer and support washer partly into the side of the brace installed in the ceiling.
Then loop the braided cable up and over the ceiling brace and place the open loop of the braided cable around the secondary
support screw. Note: The ceiling support brace may not be accessible from below. If not, it must be accessed from above.
Important: The braided cable must make a complete circle around the support brace to secure the fan (Figure 3.2).
3. Tighten the secondary support screw, securing the braided cable (Figure 3.3).
FINAL INSTALLATION
1.Use wire connectors to connect the fan wires to the power supply wires according to the wiring diagram and the following
instructions (Figure 4.1):
• Connect the green wire from the mounting bracket to the bare/green (ground) supply wire.
• Connect the white wire from the fan to the white (neutral) supply wire.
• Connect the black wire from the fan to the black (hot) supply wire.
WARNING: After the connections have been made, the connected wires should be turned upward and pushed carefully up
into the outlet box. Place the Black and White wire connections on opposite sides of the outlet box.
2. Slide the top of the motor assembly over the mounting bracket, aligning the slotted holes in the top of the motor assembly
with the pre-loosened mounting bracket screws in the mounting bracket. Twist the motor assembly clockwise to lock. Then,
re-insert the mounting bracket screws and securely tighten all screws (Figure 4.2).
3. Insert blade through slot in the side of the motor assembly. Align the holes of one blade with three blade screw holes in
underside of the motor assembly. Secure with the three blade screws and blade washers. Repeat this step for the remaining
blades (Figure 4.3).
Figure 4.2Figure 4.1 Figure 4.3
Blade Screw
Blade Washer
Slot
Mounting
Bracket Screw
Wire Connector
Black (Hot)
White (Neutral)
Bare/Green (Ground)
Green
Black White
For installation in the United States: Building codes in the U.S.A. do not require installation of a Secondary Hanging System.
If desired, the braided cable can be cut and removed using wire cutters (sold separately). Skip to FINAL INSTALLATION. For
installation in Canada: In compliance with building codes in Canada, installation of the Secondary Hanging System is required.
Slotted Hole
WARNING: Do NOT wire a
fan to a wall control.

EN I7
FINAL INSTALLATION
4. Remove one of the three fitter plate screws preassembled to the fitter plate and loosen the other two but do not remove. Feed the
single-pin connector through the center hole in the light pan. Align the keyhole slots in the light pan with the loosened screws in
the fitter plate. Turn light pan clockwise and replace the previously removed fitter plate screw. Tighten all screws (Figure 4.4).
5. Remove one of the three light pan screws from the light pan and loosen the other two but do not remove. Connect the single-
pin connector from the light pan to the single-pin connector from the light kit -- blue to black and white to white. Lift the two
keyhole slots in the light kit over the two loosened light pan screws and turn in a clockwise direction. Then, use the previously
removed light pan screw to secure the light kit to the light pan. Tighten all screws (Figure 4.5).
6. Attach the bowl assembly to the light kit by twisting the bowl assembly firmly in a clockwise direction until it is secure.
CAUTION: Avoid cross-threading the bowl assmbly during installation. Improper installation could cause the bowl assembly
to be difficult to remove or fall, which could cause serious injury (Figure 4.6).
7. Remote control comes equipped with a wall bracket. If you wish to install the wall bracket, remove the small plate to expose
the screw holes. Insert wall brackets screws through holes and into wall, then cover with the previously removed small plate.
The remote can be stored in the wall bracket for easy access (Figure 4.7).
Turn on power to fan at breaker box and the wall switch. Assembly is complete.
Figure 4.5Figure 4.4 Figure 4.6
Figure 4.7
Light Kit
Light Kit
Single-Pin
Connector
Keyhole
Slot Keyhole
Slot Light Pan Screw
Bowl Assembly
Wall Bracket
Small Plate
Wall Bracket
Screw
Fitter Plate Screw
Light Pan
Fitter Plate
Single-Pin
Connector

EN I8
OPERATING INSTRUCTIONSOPERATING INSTRUCTIONS
1. Remove the battery door from the back of the remote using a flat-head screwdriver (not included). Insert the two CR2032
batteries into the remote; ensure the positive pole of the batteries face up (as pictured) and then replace the battery door.
Press the FAN POWER button to ensure the LED indicator illuminates and the fan turns on (Figure 5.1).
2. To operate the fan using the remote, press and release the following buttons (Figure 5.2):
LED Indicator - Indicates the three speeds of the fan. It should illuminate when any remote button is pressed. If not,
replace the DC3V, CR2032 batteries.
Fan Power button has three options:
Turns the fan off or turns fan on at previously selected speed.
Increase fan speed
Lower fan speed
Sleep Timer - Turn off fan after 2 hours (2hr). Light dims to confirm function is active. Press Fan Power button to
deactivate.
Sleep Timer - Turn off fan after 4 hours (4hr). Light dims to confirm function is active. Press Fan Power button to
deactivate.
Sleep Timer - Turn off fan after 8 hours (8hr). Light dims to confirm function is active. Press Fan Power button to
deactivate.
Reverse Switch - In warmer weather, push the reverse switch left, which will result in downward airflow creating a wind
chill effect. In cooler weather, push the reverse switch right and the fan to low, which will result in upward airflow that can
help move stagnant, hot air off the ceiling area. Important: Wait for the fan to stop before moving the reverse switch. The
reverse switch must be set either completely left or right in order for the fan to function correctly. If the reverse switch is set
in the middle position, the fan will not operate.
Light Delay - Delays turning off light for one minute which allows safe exit from room. Light blinks to confirm function is
active. Press Light Control button to deactivate and turn the light off.
Home Shield™ - Simulates occupancy while away from home. Fan remains off and the light randomly turns on for a
minimum of five minutes and a maximum of 20 minutes. The light remains off for 60 minutes between events. Press and
hold button to activate. Light will blink twice to confirm Home Shield is active. Press any button to cancel.
Variable Breeze - Simulates a breeze in nature. Press and hold button to activate. Press any fan speed button to cancel.
Light Control - Tap button to turn the light off and on. Press and hold button to dim or brighten the lights.
Light Color - Press and hold button to cycle through the color temperatures from 2200K (warm white) to 6500K (daylight).
Figure 5.2Figure 5.1
Battery

EN I9
TROUBLESHOOTING
The fan does not
move.
The fan is noisy.
The fan wobbles
excessively.
The fan operates
correctly but the lights
are not working.
Remote does not
work.
1. Firmly push the reverse switch completely left or right.
2. Make sure the wall switch is turned on.
3. Turn the power on or check the fuse (breaker).
4. Turn the power off and check all connections at the ceiling outlet box.
1. Check and tighten all screws that hold the fan blades to the blade arms and the motor.
2. Replace the cracked blade.
3. Do not use a full range dimmer switch to control the fan speed.
4. Ensure the outlet box is secured to the building structure.
5. Ensure the mounting bracket is secured to the outlet box and that the screws are tight.
1. Ensure the single-pin connectors are properly secured.
2. Turn the power off and check all connections at the ceiling outlet box.
1. Check and tighten all screws that hold the fan blades to the blade arms and the blade arms to the
motor.
2. Switch one blade with a blade from the opposite side, or balance the fan using the blade
balancing kit.
3. Turn off the power. Loosen the canopy and verify that the mounting bracket is secure to the
electrical outlet box. The bracket must be flush without movement against the outlet box. Verify
the outlet box is secure.
PROBLEM CORRECTIVE ACTION
If you experience any faults, please check the Troubleshooting section below. If a problem cannot be remedied or you are
experiencing difficulty in installation, please contact Customer Service: 1-877-361-3883, Monday-Friday, 8am - 5pm, Central Time.
WARNING: Shut off the power supply before you begin any maintenance task.
1. Power surge may have cleared the memory and remote needs to be resynced to the receiver.
Syncing instructions: Turn off the power at the breaker box for at least 10 seconds and then turn
the power back on. Within 30 seconds, press and hold the “LEARN” button (Figure 5.1) on the back
of the remote for 3 seconds. The fan will turn on at high speed and light will blink twice and stay on,
signaling a successful synchronization.
2. Insert new CR2032 batteries in battery compartment of the wall control.
3. If there are several remote fans in proximity, turn the power off to those fans and re-sync the fan.

EN I10
LIMITED LIFETIME WARRANTY
Set forth below, the manufacturer, Hong Kong China Electric Appliance Company (HKC) warrants the fan motor for this ceiling
fan to be free from defects in workmanship and material for the life of the product. Also, subject to the limitations below, HKC
warrants all ceiling fan parts (“ceiling fan parts” excludes the motor and parts made in whole or in part with glass) to be free
from defects in workmanship and material for a period of one year after the date of purchase by the original purchaser at retail.
All claims must be made by the original purchaser, whether such purchaser purchased the product through a store or
contractor. Ceiling fan part defects must be reported within the first year from the date of purchase. Parts made in whole or in
part with glass and the finishes of metal and other surfaces are not warranted.
Purchasers are responsible for all costs of removing and reinstalling the product. Any damage to any part caused by ordinary
wear and tear, accident, misuse, or improper installation, is not covered by this warranty. HKC assumes no responsibility
whatsoever for fan installation. Any service performed by a non-licensed electrician will render the warranty invalid.
HKC’s sole responsibility shall be to repair or replace the motor, parts, or product within the terms stated above. HKC shall not
be liable for any loss or damage of any kind, including any incidental or consequential damages resulting directly or indirectly,
from any breach of warranty, express or implied, or any other failure of this product. Some states do not allow the exclusion or
limitation of incidental or consequential damages so this limitation may not apply to you.
If the original purchaser ceases to own the fan, this warranty is voided.
Should the purchaser encounter a problem with your fan related to defects in workmanship or materials within the warranty
period associated with the defective part, HKC agrees to replace the defective part without charge, or at its option, to replace the
ceiling fan with a comparable or superior model.
HKC’s warranties are limited to the written warranties set out in this HKC ceiling fan limited lifetime warranty. All other express
and implied warranties, including, without limitation, the implied warranty of fitness for a particular purpose and the implied
warranty of merchantability are disclaimed. Some states do not allow the disclaimer of implied warranties, so this disclaimer
may not apply to you.
REPLACEMENT PARTS LIST
For replacement parts, call our customer service department 1-877-361-3883, Monday-Friday, 8am - 5pm, Central Time.
A B C HW
The Honeywell Trademark is used under license
from Honeywell International Inc.
Honeywell International Inc. makes no
representations or warranties with respect to
this product.
This product is manufactured for
Hong Kong China Electric Appliance, LTD.
3350 Players Club Parkway, Suite 225
Memphis, TN 38125
1 [phone]
9860 • 020223
A Bowl Assembly 4A000013900 4A000010140
B Blade (x5) 4A086410001 4A086410002
C Remote Pack 4L000016870 4L000016870
HW Hardware Bag 4A000023600 4A000023600
51859 51860
Home