Honeywell FS24X User manual

DTM User Manual
FS24X/FS20X Flame Detector

FS24X/FS20X DTM Manual, Issue 1
1 Content
2Introduction......................................................................................................................................1
3Software installation ........................................................................................................................2
3.1 Required software / software components..............................................................................2
3.2 DTM Toolkit downloads...........................................................................................................2
3.3 System requirements...............................................................................................................2
3.3.1 System resources............................................................................................................2
3.3.2 Operating systems...........................................................................................................2
3.3.3 Hard disk space...............................................................................................................3
3.4 Installing DTM setup................................................................................................................3
4Operation.........................................................................................................................................7
4.1 Establish connection with the device.......................................................................................7
4.1.1 Possible problems while connecting to device..............................................................12
4.1.2 Setting HART polling address .......................................................................................13
4.1.3 Device manuals.............................................................................................................15
4.2 Topology scan .......................................................................................................................15
4.3 PACTware menu structure and items ...................................................................................18
4.3.1 DTM specific menu items ..............................................................................................18
4.3.2 Frame specific menu items............................................................................................18
4.4 Operation...............................................................................................................................19
4.4.1 DTM graphical user interface ........................................................................................19
4.5 Create a project.....................................................................................................................21
5Online function of the device type .................................................................................................21
5.1 Measured value function .......................................................................................................21
5.2 Diagnosis function .................................................................................................................23
5.3 Online parameterization function...........................................................................................23
5.3.1 First “Tab”: Process Variables .......................................................................................24
5.3.2 Second “Tab”: Basic Setup............................................................................................25
5.3.3 Third “Tab”: Detailed Setup ...........................................................................................26
5.3.4 Fourth “Tab”: Review.....................................................................................................27
6Offline parameterization function...................................................................................................27
6.1 Load from device...................................................................................................................30
6.2 Store to device.......................................................................................................................31
7Print ...............................................................................................................................................31

FS24X/FS20X DTM Manual, Issue 1
1
2 Introduction
The purpose of this document is to support the plant operators with commissioning, operation,
configuration and diagnosis of the FS24X/FS20X Rev 1. The FS24X is the latest generation
high technology Multi-Spectrum Triple IR (IR/IR/IR/Visible) Fire and Flame detector and the
FS20X is the latest generation high technology Multi-Spectrum (UV/Dual IR/VIS) Fire and
Flame detector.
The FS24X/FS20X device can be configured and operated by a device type, managed by a
DTM (Device Type Manager) that provides an easy to use user interface for accessing device
variables, configuration parameters and diagnosis information.
The FS24X/FS20X device should have one optional HART module installed to use HART
communication. Please contact Honeywell representatives for the part numbers and availabil-
ity.
The FS24X/FS20X device type offers the combination of FDT and EDDL technologies and a
uniform user interface according to the FDT style guide. It is a full-featured device DTM that
carries the standard EDD-Interpreter components to execute the EDD during runtime. Be-
cause it is using existing device descriptions, plant operators will experience a familiar oper-
ating concept in the DTM.
Every effort has been made to ensure the accuracy of this document, however, Honeywell
Analytics can assume no responsibility for any errors or omissions in this document or their
consequences.
Honeywell Analytics would greatly appreciate being informed of any errors or omissions that
may be found in the content of this document.
For information not covered in this document, or if there is a requirement to send com-
ments/corrections about this document, please contact Honeywell Analytics using the contact
details given on the back page.
Honeywell Analytics reserve the right to change or revise the information supplied in
this document without notice and without obligation to notify any person or organiza-
tion of such revision or change. If information is required that does not appear in this
document, contact the local distributor/agent or Honeywell Analytics.
WARNING
For safety reasons this equipment must be operated by qualified personnel only. Read
and understand the instruction manual completely before operating or servicing the
equipment. For information regarding the FS24X/FS20X device, please check the Tech-
nical Manual (see § )

FS24X/FS20X DTM Manual, Issue 1
2
3 Software installation
3.1 Required software / software components
In order to be able to use the FS24X/FS20X HART DTM and to go online with the device you
need the following components:
•FDT Frame application (PACTware or some other FDT application supporting FDT
1.2.x)
•HART Communication DTM (it represents the communication hardware needed for
connecting the field devices to the automation software): There is a free version of
HART Communication DTM available for download from CodeWrights website
(www.codewrights.de)
•Honeywell Analytics HART DTM Library
•Microsoft .NET Framework 3.5 (incl. Service Packs)/CRL2
•HART modem (RS232 or USB interfaces of the companies Endress+Hauser, Microflex
or MACTek)
3.2 DTM Toolkit downloads
Go to one of FS24X/FS20X website:
•https://www.honeywellanalytics.com/en/products/FS20X-Flame-Detector
•https://www.honeywellanalytics.com/en/products/FS24X-Flame-Detector
Select "Software"
Select "Drivers & Downloads"
Download the toolkit. It will contain the following items:
•PACTware FDT Frame
•HART Communication DTM FDT 1.2
•Most recent version of the Honeywell Analytics DTM Library
3.3 System requirements
3.3.1 System resources
Proper execution of the DTMs requires a standardPC with at leastfollowing system resources:
•1 gigahertz (GHz) or faster 32-bit (x86) or 64-bit (x64) processor with at least 2 cores
•1 gigabyte (GB) RAM (32-bit) or 2 GB RAM (64-bit)
•Screen Resolution at least 1024x768 pixels
•Free Hard disk space: approx. 2 GB
•Microsoft .NET Framework 3.5 (incl. Service Packs)/CRL2
3.3.2 Operating systems
The DTM will run under the following operating systems:

FS24X/FS20X DTM Manual, Issue 1
3
•Windows 7
•Windows 10
•Windows Server 2012
3.3.3 Hard disk space
The Honeywell Analytics DTM Library HART requires approx. 50 MB hard disk space.
3.4 Installing DTM setup
Please install the Frame Application PACTware (see § Error! Reference source not found.)
first, followed by the HART Communication DTM (see § Error! Reference source not
found.).
Install Honeywell Analytics HART DTM Library (see § Error! Reference source not found.)
as follows:
1. Execute the setup by double-clicking on “Setup.exe” Application
On the right-hand side: Extract the installation package to your local disk. Structure
and files similar to the following example shall appear:
2. On the Welcome Screen, click “Next“:

FS24X/FS20X DTM Manual, Issue 1
4
3. On the next screen, accept the License Agreement and click “Next”:
4. Adjust the installation path to your needs (choose the components to install and the
destination directory) by pressing "Browse" or just confirm the default installation path
with "Install":

FS24X/FS20X DTM Manual, Issue 1
5
5. A window indicating the installation progress is displayed:
6. Confirm with “Finish” to close the setup wizard:

FS24X/FS20X DTM Manual, Issue 1
6
7. Open your FDT-Frame Application (PACTware) and update the device catalog:
8. Create an updated PACTware DTM catalog by clicking “yes”:

FS24X/FS20X DTM Manual, Issue 1
7
9. After the update you will find the device types listed in your catalog:
4 Operation
4.1 Establish connection with the device
After completion of § 2, please follow the steps described below for establishing the connec-
tion with your device using a serialHART modem and the CodeWrights HART Communication
DTM (setting up a project in another frame or using another communication DTM might differ):
1. Open the PACTware frame application and make sure you have updated the “Device
catalog” (if not already done yet) as mentioned in § 3.4 Position 7
2. Connect the device and the serial HART modem as described in the FS24X/FS20X
device manuals (see § for technical details)
3. Connect the modem connector to the PC COM port (serial modem) or USB port (USB
Modem).
4. Right-click on “HOST PC” in the project view on the left-hand side and select “Add
device” to add the HART Communication DTM. On the next screen, select the DTM
and click “ok”:

FS24X/FS20X DTM Manual, Issue 1
8
5. Right-click on “HOST PC” in the project view on the left-hand side and select “Param-
eter”:
6. Double-click on the HART Communication DTM and adjust the settings according to
your hardware connection (you can find this information in Computer/Properties/De-
vice Manager/Ports/Communications Port) then click “ok”:
7. Now “Connect” the HART Communication DTM:

FS24X/FS20X DTM Manual, Issue 1
9

FS24X/FS20X DTM Manual, Issue 1
10
8. Now right-click on the communication DTM and select “Add device”:
9. Select the right part number of the HART module installed with your device and click
"ok".

FS24X/FS20X DTM Manual, Issue 1
11
10. Go online by right-clicking on the device DTM and select “Connect” to connect the
FS24X/FS20X device:
11. Now your device should be online, and the symbol “Connected” appears:
12. With a click right on the FS24X/FS20X device type in your project a detailed context
menu with appear. Browse to Parameter/Online Parameterization and click left on it:

FS24X/FS20X DTM Manual, Issue 1
12
13. Connection to the device is now used to read data from the device and visualize them:
4.1.1 Possible problems while connecting to device
The following ERROR MESSAGE: “Connection to device could not be established” can be
caused by the following:
•Transmitter is not powered
•HART serial interface is not connected
•HART modem and HART Communication DTM are using different serial ports (COM1,
COM2, …). To determine which COM port is the right one:
Click on Windows Start button, then type “Device Manager” and confirm with Enter.
In opened “Device Manager”, the section “Ports (COM & LPT)” shows a list of the
available COM-Ports. The number after “COM” needs to match with the setting that
was made in the HART Communication DTM. If a certain USB-Modem is unplugged
from the USB-port, its COM-port will disappear from this list.

FS24X/FS20X DTM Manual, Issue 1
13
It may be necessary to DISCONNECT the Communication DTM and then CONNECT again
to successful establish communications.
•The HART polling address set in the device is not the same as set in the device DTM.
For details, see §4.1.2
•The device is connectedto a HART Multiplexer and the Multiplexer configuration is not
prepared for this device. In most cases, the HART Multiplexer has to be triggered to
recognize the device at one of its loops. It does not scan loops the time. Many HART-
Multiplexer require the polling address of the device to the 0. Forchanging the address
of your device to 0, see §4.1.2
•The FSX-014
4.1.2 Setting HART polling address
The HART Technology is capable to connect more than one HART device to a single 4-20mA
loop. This is called multidrop-mode.
The identification of a HART device is done via its polling address. The valid range is 0-63,
while 0 is a special case:
Only for address 0, the loop current will be influenced by measuring and alarm of the
device, for any other address it stays at 4mA, independent of measuring or alarm. In-
fluencing the current also requires the device to be the only HART device in the loop.
Device and DTM must be set to the same polling address, and no other device attached to
this loop shall use this address. Using an address twice will lead to a broken HART commu-
nication for one or more devices.
In many casesmultidrop-mode is not in use, and the address is “0”. This is the default address
of the DTMs.
Note:
The FSX-A014 (FS24X/FS20X) device does only support polling addresses between 0
and 15. Setting any higher address will lead to a broken communication that can’t be
set back via the DTM anymore.
4.1.2.1 Setting the polling address of a HART device
•Add the HART Commication DTM to your environment, if not already done.
•Set „End address“ to a higher value, e.g. „5“
•Adjust the COM-Port settings to get access to your HART-Modem (see §4.1.1)
•Establish a connection to the COM-Port: right click on the HART Communication DTM
and choose “Connect”. The “two plug”-Icon will change and now the plugs are con-
nected and green.
•Again, right click on the HART Communication DTM an choose “Additional func-
tions/Change device address”
•While opening the view, the HART bus is scannedfor devices within the addressrange
between “start address” and “end address”: The result may look like this
•Here, a device is found at address “0”

FS24X/FS20X DTM Manual, Issue 1
14
•To change the device address, click on change and choose the new address.
Note: For FSX-A014 (FS24X/FS20X) device, use addresses between 0 and 15
only. See §4.1.2
•Confirm with “OK”
•Click on “Refresh” to repeat the scan again and verify your changes.
Note: For FSX-A014 (FS24X/FS20X) device, any polling address between 1 and
15 (See §4.1.2) will only be discovered if the scan for a device at address 0 is
skipped. To do this, disconnect the HART communication DTM (right click at the
icon in the topology, Disconnect) and open the Parameterization (double click).
Change the values of “Start address” and “End address” to get a range that fits
to your needs. E.g. if you want to check if your device has accepted a set to
polling address 3, the closest useful address range is from 3 to 3. The widest
useful range to scan for an FSX-A014 (FS24X/FS20X) device with a polling ad-
dress other than 0 is from 1 to 15, as this specific device will not workwith higher
addresses. Setting the bounds for the scan is described in the following step.
•If you do notfind your device anymore, the newaddress is probably outsidethe bounds
of “Start address” and “End address”. These bounds can be changed if the HART
Communication DTM is disconnected: Right click on the DTM, choose “Disconnect”.
Then, open the “Parameterization” of the HART Communication DTM to find “Start
address” and “End address”. Choose “Apply” to take over your changes.
•To scan again it is necessary to connect the DTM.
4.1.2.2 Setting the polling address of a HART DTM
•If not already done, add HART Communication DTM and your device DTM to the pro-
ject.
•To set the device DTM address, the HART Communication DTM needs to be discon-
nected: Right click on the DTM, choose “Disconnect”.

FS24X/FS20X DTM Manual, Issue 1
15
•Again, right click on the Communication DTM and choose “Additional func-
tions/Change DTM address”. The List of DTMs attached to this Communication DTM
will appear.
•Via “Change” the address of the DTM can be adjusted
•Confirm with „OK“
•Via “Refresh” the address of each attached DTM can be read out again.
•To establish a connection to your device, continue with the instructions from §4.1 Po-
sition 10.
4.1.3 Device manuals
For more details regarding error messages, please download the technical manuals:
1. FS20X Flame Detector
https://www.honeywellanalytics.com/en/products/FS20X-Flame-Detector
2. FS24X Flame Detector
https://www.honeywellanalytics.com/en/products/FS24X-Flame-Detector
4.2 Topology scan
Note:
The feature described here does not work for the FSX-A014 (FS24X/FS20X) device. The
scan result will not lead to an automatic match. A manual assignment is required.
Please follow the steps described in §4.1 to manually add the matching device type. If
the polling address of the device is not 0, please follow the steps described in §4.1.2.1
to set the address.
Another way to connect the device is to use the function “Topology scan”. This function is
searching automatically the device and adds it to the project if the match is perfect.
Just follow the instructions as mentioned in § 4.1 from Position 1-6, then continue with the
following instructions:
1. Right-click on the communication DTM and select “Topology scan” with a click:

FS24X/FS20X DTM Manual, Issue 1
16
2. The Topology scan window appears. Click on the “Play”-Button in the lower left corner
to start the scan. During scan the scanning progress is displayed:

FS24X/FS20X DTM Manual, Issue 1
17
3. Select the device type that matches best and confirm with “Apply”:
4. The device is added to the project and the Topology Scan can be closed:
5. Now continue with the instructions from §4.1 Position 10.

FS24X/FS20X DTM Manual, Issue 1
18
4.3 PACTware menu structure and items
By right-clicking on the device DTM you will find a menu list. Some menu items are character-
istic for DTM and some for frame (in the shown example PACTware):
4.3.1 DTM specific menu items
•Measured value (offers real time information about the HART loop current (mA and
%), the fire detection status and the device condition.
•Parameter (offers information regarding the complete device parameters which can be
set according to your measurement application)
oOnline parameterization
oParameterization (which refers to offline parameterization)
•Diagnosis (offers real time information about the device status)
•Additional functions (offers information regarding the DTM, like version number, man-
ufacturer, registration status, etc)
oAbout DTM
•Load from device (is used for uploading data set from the device to the offline param-
eterization). Perform this operation in order to store the device configuration in the
Frame Application’s project file or database.
•Store to device (is used for downloading the offline parameterization data to the de-
vice). Perform this operation in order to download and restore a device configuration
from a saved project to the device.
4.3.2 Frame specific menu items
The other items shown in the figure above are frame characteristic items. In the following
pages we will describe the DTM characteristic items. For more information regarding the
Frame items, please check www.pactware.com or the respective operating manual of your
Frame Application.